Comparative analysis of forming limit diagram of Al 5052-H32 and Al 6063 T5

2021 ◽  
pp. 2150013
Author(s):  
B. R. Mahesh ◽  
J. Satheesh
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Aluminium Alloys ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Specific Load ◽  
Analysis Software ◽  
Minor Strain ◽  
Good Agreement

Formability of a material is found to be one of the important characteristic of a sheet metal to know the variation of the major and minor strain of a sheet metal, using this value one can predict the forming limit diagram of sheet metal, forming limit diagram gives the behavior of sheet metals under various loads and also helps in the prediction of breakage or necking of the material under specific load and velocity of the punch. Current study is mainly focused on obtaining the forming limit diagram of two different aluminium alloys like Al-5052 H32 and Al-6063 T5 using numerical analysis software PAMSTAMP and the results obtained are validated by conducting experiments, there is a good agreement of results between the experimental and numerical values. The forming limit diagram of the mentioned alloys helps in manufacturing of automobile and electric vehicle parts.

A New Approach to the Evaluation of Forming Limits in Sheet Metal Forming

2015 ◽  
Vol 639 ◽  
pp. 333-338 ◽  
Author(s):  
Marion Merklein ◽  
Andreas Maier ◽  
Daniel Kinnstätter ◽  
Christian Jaremenko ◽  
Emanuela Affronti
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Strain History ◽  
Failure Behavior ◽  
Forming Limits ◽  
Optical Strain Measurement ◽  
Optical Strain

The forming limit diagram (FLD) is at the moment the most important method for the prediction of failure within sheet metal forming operations. Key idea is the detection of the onset of necking in dependency of different sample geometry. Whereas the standardized evaluation methods provides very robust and reliable results for conventional materials like deep drawing steels, the determined forming limits for modern light materials are often too conservative due to the different failure behavior. Therefore, within this contribution a new and innovative approach for the identification of the onset of necking will be presented. By using a pattern recognition-based approach in combination with an optical strain measurement system the complete strain history during the test can be evaluated. The principal procedure as well as the first promising results are presented and discussed.

An Aid to Practical Sheet Metal Forming

1970 ◽  
Vol 12 (6) ◽  
pp. 443-445
Author(s):  
R. Pearce ◽  
J. Woodthorpe
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Forming Limit Diagram ◽  
Forming Limit ◽  
Analytical Technique

Until recently, no analytical technique was available for the study of failure in complex sheet metal pressing. However, if the maximum ( e1) and minimum ( e2) principal surface strains at failure on sheet metal pressing are measured, a plot of e1 against e2 results in a so-called forming limit diagram. FLD can be constructed in the laboratory and used as an aid to die try-out, production failures and metal specification.

Modelling of Instability and Fracture Effects in the Sheet Metal Forming Based on an Extended X-FLC Concept

2016 ◽  
Vol 725 ◽  
pp. 15-32
Author(s):  
Pavel Hora ◽  
Bekim Berisha ◽  
Maysam Gorji ◽  
Holger Hippke
Keyword(s):  
Sheet Metal ◽  
Cross Section ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Forming Limit Diagram ◽  
Al Alloys ◽  
Forming Limit ◽  
Section Method ◽  
The Real ◽  
Cross Section Method

The industrial necking prediction in sheet metal forming is still based on the Forming Limit Diagram (FLD) as initially proposed by Keeler. The FLD is commonly specified by the Nakajima tests and evaluated with the so called cross section method. Although widely used, the FLC concept has numerous serious limitations. In the paper the influences of bending on the FLC as well as postponed crack limits will be discussed. Both criteria will be combined to an extended FLC concept (X-FLC). The new concept demonstrates that the Nakajima tests are not only appropriate for the evaluation of the necking instability, but also for the detection of the real crack strains. For the evaluation of the crack strains, a new local thinning method is proposed and tested for special 6xxx Al-alloys.

Determination of FLD for Ti-6Al-4V Titanium Alloy Sheet

2016 ◽  
Vol 687 ◽  
pp. 171-178
Author(s):  
Piotr Lacki
Keyword(s):  
Titanium Alloy ◽  
Numerical Simulations ◽  
Real Time ◽  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Forming Limit Diagram ◽  
Alloy Sheet ◽  
Forming Limit

Ti-6Al-4V is the most widely applied titanium alloy in technology and medicine due its good mechanical properties combined with low density and good corrosion resistance. However, poor technological and tribological properties make it very difficult to process, including the problems with sheet-metal forming. The best way to evaluate sheet drawability is to use Forming Limit Diagram (FLD), which represents a line at which failure occurs. FLD allows for determination of critical forming areas.The FLDs can be determined both theoretically and experimentally. Recently, special optical strain measurement systems have been used to determine FLDs.In this study, material deformation was measured with the Aramis system that allows for real-time observation of displacements of the stochastic points applied to the surface using a colour spray. The FLD was determined for Ti-6Al-4V titanium alloy sheet with thickness of 0.8 mm. In order to obtain a complete FLD, a set of 6 samples with different geometries underwent plastic deformation in stretch forming i.e. in the Erichsen cupping test until the appearance of fracture.The real-time results obtained from the ARAMIS software for multiple measurement positions from the test specimen surface were compared with numerical simulations of the cupping tests. The numerical simulations were performed using the PamStamp 2G v2012 software dedicated for analysis of sheet-metal forming processes. PamStamp 2G is based on the Finite Element method (FEM). The major and minor strains were analysed. The effect of friction conditions on strain distribution was also taken into consideration

scholarly journals Laser Welding of High-strength Aluminium Alloys for the Sheet Metal Forming Process

Procedia CIRP ◽  
2014 ◽  
Vol 18 ◽  
pp. 203-208 ◽  
Author(s):  
J. Enz ◽  
S. Riekehr ◽  
V. Ventzke ◽  
N. Sotirov ◽  
N. Kashaev
Keyword(s):  
Laser Welding ◽  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Aluminium Alloys ◽  
High Strength ◽  
Forming Process ◽  
Metal Forming Process

Preliminary Studies on the Determination of FLD for Single Point Incremental Sheet Metal Forming

2012 ◽  
Vol 504-506 ◽  
pp. 863-868 ◽  
Author(s):  
Miklos Tisza ◽  
Péter Zoltán Kovács ◽  
Zsolt Lukács
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
New Technologies ◽  
Single Point ◽  
Research Work ◽  
Dimensional Accuracy ◽  
Forming Limit ◽  
Incremental Sheet Metal Forming

Development of new technologies and processes for small batch and prototype production of sheet metal components has a very important role in the recent years. The reason is the quick and efficient response to the market demands. For this reasons new manufacturing concepts have to be developed in order to enable a fast and reliable production of complex components and parts without investing in special forming machines. The need for flexible forming processes has been accelerated during the last 15 years, and by these developments the technology reaches new extensions. Incremental sheet metal forming (ISMF) may be regarded as one of the promising developments for these purposes. A comprehensive research work is in progress at the University of Miskolc (Hungary) to study the effect of important process parameters with particular emphasis on the shape and dimensional accuracy of the products and particularly on the formability limitations of the process. In this paper, some results concerning the determination of forming limit diagrams for single point incremental sheet metal forming will be described.

Surrogate POD Models for Parametrized Sheet Metal Forming Applications

2013 ◽  
Vol 554-557 ◽  
pp. 919-927 ◽  
Author(s):  
Hamdaoui Mohamed ◽  
Guénhaël Le Quilliec ◽  
Piotr Breitkopf ◽  
Pierre Villon
Keyword(s):  
Finite Element ◽  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Optimization Problems ◽  
Strain Tensor ◽  
Forming Limit ◽  
Work Piece ◽  
Displacement Fields ◽  
Lagrange Strain

The aim of this work is to present a POD (Proper Orthogonal Decomposition) based surrogate approach for sheet metal forming parametrized applications. The final displacement field for the stamped work-piece computed using a finite element approach is approximated using the method of snapshots for POD mode determination and kriging for POD coefficients interpolation. An error analysis, performed using a validation set, shows that the accuracy of the surrogate POD model is excellent for the representation of finite element displacement fields. A possible use of the surrogate to assess the quality of the stamped sheet is considered. The Green-Lagrange strain tensor is derived and forming limit diagrams are computed on the fly for any point of the design space. Furthermore, the minimization of a cost function based on the surrogate POD model is performed showing its potential for solving optimization problems.

Stress-Based Forming Limits in Sheet-Metal Forming

2000 ◽  
Vol 123 (4) ◽  
pp. 417-422 ◽  
Author(s):  
Thomas B. Stoughton
Keyword(s):  
Sheet Metal ◽  
Sheet Metal Forming ◽  
Metal Forming ◽  
Strain Path ◽  
Forming Limit ◽  
Stress Strain ◽  
Strain Relation ◽  
Stress Strain Relation ◽  
The Stability ◽  
Definition Of

A strain-based forming limit criterion is widely used throughout the sheet-metal forming industry to gauge the stability of the deformed material with respect to the development of a localized neck prior to fracture. This criterion is strictly valid only when the strain path is linear throughout the deformation process. There is significant data that shows a strong and complex dependence of the limit criterion on the strain path. Unfortunately, the strain path is never linear in secondary forming and hydro-forming processes. Furthermore, the path is often found to be nonlinear in localized critical areas in the first draw die. Therefore, the conventional practice of using a path-independent strain-based forming limit criterion often leads to erroneous assessments of forming severity. Recently it has been reported that a stress-based forming limit criterion appears to exhibit no strain-path dependencies. Subsequently, it has been suggested that this effect is not real, but is due to the saturation of the stress-strain relation. This paper will review and compare the strain-based and stress-based forming limit criteria, looking at a number of factors that are involved in the definition of the stress-based forming limit, including the role of the stress-strain relation.

Sign in / Sign up

Export Citation Format

Share Document