scholarly journals Numerical Investigation on the Influence of Hot Streak Temperature Ratio in a High-Pressure Stage of Vaneless Counter-Rotating Turbine

2007 ◽  
Vol 2007 ◽  
pp. 1-14 ◽  
Author(s):  
Zhao Qingjun ◽  
Wang Huishe ◽  
Zhao Xiaolu ◽  
Xu Jianzhong
Keyword(s):  
High Pressure ◽  
Secondary Flow ◽  
Heat Load ◽  
Rotor Blades ◽  
Inlet Temperature ◽  
Combined Effects ◽  
Temperature Ratio ◽  
Flow Angle ◽  
Hot Streak ◽  
Relative Flow

The results of recent studies have shown that combustor exit temperature distortion can cause excessive heat load of high-pressure turbine (HPT) rotor blades. The heating of HPT rotor blades can lead to thermal fatigue and degrade turbine performance. In order to explore the influence of hot streak temperature ratio on the temperature distributions of HPT airfoil surface, three-dimensional multiblade row unsteady Navier-Stokes simulations have been performed in a vaneless counter-rotating turbine (VCRT). The hot streak temperature ratios from 1.0 (without hot streak) to 2.4 were used in these numerical simulations, including 1.0, 1.2, 1.6, 2.0, and 2.4 temperature ratios. The hot streak is circular in shape with a diameter equal to 25%of the span. The center of the hot streak is located at 50%of span and 0%of pitch (the leading edge of the HPT stator vane). The predicted results show that the hot streak is relatively unaffected as it migrates through the HPT stator. The hot streak mixes with the vane wake and convects towards the pressure surface (PS) of the HPT rotor when it moves over the vane surface of the HPT stator. The heat load of the HPT rotor increases with the increase of the hot streak temperature ratio. The existence of the inlet temperature distortion induces a thin layer of cooler air in the HPT rotor, which separates the PS of the HPT rotor from the hotter fluid. The numerical results also indicating the migration characteristics of the hot streak in the HPT rotor are predominated by the combined effects of secondary flow and buoyancy. The combined effects that induce the high-temperature fluid migrate towards the hub on the HPT rotor. The effect of the secondary flow on the hotter fluid increases as the hot streak temperature ratio is increased. The influence of buoyancy is directly proportional to the hot streak temperature ratio. The predicted results show that the increase of the hot streak temperature ratio trends to increase the relative Mach number at the HPT rotor outlet, and decrease the relative flow angle from 25%to 75%span at the HPT rotor outlet. In the other region of the HPT outlet, the relative flow angle increases when the hot streak temperature ratio is increased. The predicted results also indicate that the isentropic efficiency of the VCRT decreases with the increase of the hot streak temperature ratio.

Influence of Hot Streak/Airfoil Count Ratios on High Pressure Stage of a Vaneless Counter-Rotating Turbine

2008 ◽  
Author(s):  
Qingjun Zhao ◽  
Huishe Wang ◽  
Fei Tang ◽  
Xiaolu Zhao ◽  
Jianzhong Xu
Keyword(s):  
High Pressure ◽  
Three Dimensional ◽  
Turbine Rotor ◽  
Rotor Blades ◽  
Peak Temperature ◽  
Combined Effects ◽  
High Pressure Turbine ◽  
Flow Angle ◽  
Count Ratio ◽  
Hot Streak

In order to reveal the effects of the hot streak/airfoil count ratio on the heating patterns of high pressure turbine rotor blades in a Vaneless Counter-Rotating Turbine, three-dimensional unsteady Navier-Stokes simulations have been performed. In these simulations, the ratio of the number of hot streaks to the number of the high pressure turbine vanes and rotors is 1:3:3, 1:2:2, 2:3:3 and 1:1:1, respectively. The numerical results show that the migration characteristics of the hot streak in the high pressure turbine rotor are predominated by the combined effects of secondary flow and buoyancy. The combined effects induce the high temperature fluid migrate towards the hub in the high pressure turbine rotor. And the combined effects become more intensified when the hot streak/airfoil count ratio increases. The results also indicate that the peak temperature of the hot streak is dissipated as the hot streak goes through the high pressure turbine vane or the rotor. The dissipated extent of the peak temperature in the high pressure turbine stator and the rotor is increased as the hot streak-to-airfoil ratio increases. And the increase of the hot streak/airfoil count ratio trends to increase the relative Mach number at the high pressure turbine outlet. The relative flow angle from 23% to 73% span at the high pressure turbine outlet decreases as the hot streak-to-airfoil ratio increases. The results also indicate that the isentropic efficiency of the Vaneless Counter-Rotating Turbine is decreased as the hot streak/airfoil count ratio increases.

Influence of Hot Streak Temperature Ratio on Low Pressure Stage of a Vaneless Counter-Rotating Turbine

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Zhao Qingjun ◽  
Tang Fei ◽  
Wang Huishe ◽  
Du Jianyi ◽  
Zhao Xiaolu ◽  
...  
Keyword(s):  
High Pressure ◽  
Secondary Flow ◽  
Low Pressure ◽  
Turbine Rotor ◽  
Temperature Ratio ◽  
High Pressure Turbine ◽  
Flow Angle ◽  
Pressure Stage ◽  
Low Pressure Turbine ◽  
Hot Streak

In order to explore the influence of hot streak temperature ratio on the low pressure stage of a vaneless counter-rotating turbine, three-dimensional multiblade row unsteady Navier–Stokes simulations have been performed. The predicted results show that hot streaks are not mixed out by the time they reach the exit of the high pressure turbine rotor. The separation of colder and hotter fluids is observed at the inlet of the low pressure turbine rotor. After making interactions with the inner-extending and outer-extending shock waves in the high pressure turbine rotor, the hotter fluid migrates toward the pressure surface of the low pressure turbine rotor, and most of the colder fluid migrates to the suction surface of the low pressure turbine rotor. The migrating characteristics of the hot streaks are dominated by the secondary flow in the low pressure turbine rotor. The results also indicate that the secondary flow intensifies in the low pressure turbine rotor when the hot streak temperature ratio is increased. The effects of the hot streak temperature ratio on the relative flow angle at the inlet of the low pressure turbine rotor are very remarkable. The isentropic efficiency of the vaneless counter-rotating turbine decreases as the hot streak temperature ratio is increased.

Influence of Hot Streak Temperature Ratio on Low Pressure Stage of a Vaneless Counter-Rotating Turbine

2007 ◽  
Author(s):  
Qingjun Zhao ◽  
Fei Tang ◽  
Huishe Wang ◽  
Jianyi Du ◽  
Xiaolu Zhao ◽  
...  
Keyword(s):  
Shock Wave ◽  
High Pressure ◽  
Secondary Flow ◽  
Low Pressure ◽  
Turbine Rotor ◽  
Temperature Ratio ◽  
High Pressure Turbine ◽  
Pressure Stage ◽  
Low Pressure Turbine ◽  
Hot Streak

In order to explore the influence of hot streak temperature ratio on low pressure stage of a Vaneless Counter-Rotating Turbine, three-dimensional multiblade row unsteady Navier-Stokes simulations have been performed. The predicted results show that hot streaks are not mixed out by the time they reach the exit of the high pressure turbine rotor. The separation of colder and hotter fluids is observed at the inlet of the low pressure turbine rotor. After making interactions with the inner-extending shock wave and outer-extending shock wave in the high pressure turbine rotor, the hotter fluid migrates towards the pressure surface of the low pressure turbine rotor, and the most of colder fluid migrates to the suction surface of the low pressure turbine rotor. The migrating characteristics of the hot streaks are predominated by the secondary flow in the low pressure turbine rotor. The effect of buoyancy on the hotter fluid is very weak in the low pressure turbine rotor. The results also indicate that the secondary flow intensifies in the low pressure turbine rotor when the hot streak temperature ratio is increased. The effects of the hot streak temperature ratio on the relative Mach number and the relative flow angle at the inlet of the low pressure turbine rotor are very remarkable. The isentropic efficiency of the Vaneless Counter-Rotating Turbine decreases as the hot streak temperature ratio is increased.

scholarly journals Effect of Inlet Temperature Non-Uniformity on High-Pressure Turbine Performance

2010 ◽  
Author(s):  
Craig I. Smith ◽  
Dongil Chang ◽  
Stavros Tavoularis
Keyword(s):  
High Pressure ◽  
Heat Load ◽  
Stokes Equations ◽  
Computation Time ◽  
Radial Pressure ◽  
Navier Stokes ◽  
Inlet Temperature ◽  
High Pressure Turbine ◽  
Navier Stokes Equations ◽  
Hot Streak

The temperature of the flow entering a high-pressure turbine stage is inherently non-uniform, as it is produced by several discrete, azimuthally-distributed combustors. In general, however, industrial simulations assume inlet temperature uniformity to simplify the preparation process and reduce computation time. The effects of a non-uniform inlet field on the performance of a commercial, transonic, single-stage, high-pressure, axial turbine with a curved inlet duct have been investigated numerically by performing URANS (Unsteady Reynolds-Averaged Navier-Stokes equations) simulations with the SST (Shear Stress Transport) turbulence model. By adjusting the alignment of the experimentally-based inlet temperature field with respect to the stator vanes, two clocking configurations were generated: an aligned case, in which each hot streak impinged on a vane and a misaligned case, in which each hot streak passed between two vanes. In the aligned configuration, the hot streaks produced higher time-averaged heat load on the vanes and lower heat load on the blades. As the aligned hot streaks impinged on the stator vanes, they also spread spanwise due to the actions of the casing passage vortices and the radial pressure gradient; this resulted in a stream entering the rotor with relatively low temperature variations. The misaligned hot streaks were convected undisturbed past the relatively cool vane section. Relatively high time-averaged enthalpy values were found to occur on the pressure side of the blades in the misaligned configuration. The non-uniformity of the time-averaged enthalpy on the blade surfaces was lower in the aligned configuration. The flow exiting the rotor section was much less non-uniform in the aligned case, but differences in calculated efficiency were not significant.

Rotor Blade Heat Transfer of High Pressure Turbine Stage Under Inlet Hot-Streak and Swirl

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
A. Rahim ◽  
L. He
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Heat Load ◽  
Design Space Exploration ◽  
Role Reversal ◽  
Dominant Factor ◽  
Inlet Temperature ◽  
Turbine Stage ◽  
Lean Burn ◽  
Hot Streak

A key consideration in high pressure (HP) turbine designs is the heat load experienced by rotor blades. Impact of turbine inlet nonuniformity of combined temperature and velocity traverses, typical for a lean-burn combustor exit, has rarely been studied. For general turbine aerothermal designs, it is also of interest to understand how the behavior of lean-burn combustor traverses (with both hot-streak and swirl) might contrast with those for a rich-burn combustor (largely hot-streak only). In the present work, a computational study has been carried out on the aerothermal performance of a HP turbine stage under nonuniform temperature and velocity inlet profiles. The analyses are primarily conducted for two combined hot-streak and swirl inlets, with opposite swirl directions. In addition, comparisons are made against a hot-streak only case and a uniform inlet. The effects of three nozzle guide vane (NGV) shape configurations are investigated: straight, compound lean (CL) and reverse CL (RCL). The present results reveal a qualitative change in the roles played by heat transfer coefficient (HTC) and fluid driving (“adiabatic wall”) temperature, Taw. It has been shown that the blade heat load for a uniform inlet is dominated by HTC, whilst a hot-streak only case is largely influenced by Taw. However, in contrast to the hot-streak only case, a combined hot-streak and swirl case shows a role reversal with the HTC being a dominant factor. Additionally, it is seen that the swirling flow redistributes radially the hot fluid within the NGV passage considerably, leading to a much ‘flatter’ rotor inlet temperature profile compared to its hot-streak only counterpart. Furthermore, the rotor heat transfer characteristics for the combined traverses are shown to be strongly dependent on the NGV shaping and the inlet swirl direction, indicating a potential for further design space exploration. The present findings underline the need to clearly define relevant combustor exit temperature and velocity profiles when designing and optimizing NGVs for HP turbine aerothermal performance.

Rotor Blade Heat Transfer Characteristics for High Pressure Turbine Stage Under Inlet Temperature and Velocity Traverses

2014 ◽  
Author(s):  
A. Rahim ◽  
L. He ◽  
E. Romero
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Heat Load ◽  
Inlet Temperature ◽  
Turbine Stage ◽  
Heat Transfer Characteristics ◽  
Lean Burn ◽  
Transfer Characteristics ◽  
Hot Streak ◽  
The Impact

One of the key considerations in high pressure (HP) turbine design is the heat load experienced by rotor blades. The impact of turbine inlet non-uniformities on the blades in the form of combined temperature and velocity traverses, typical for a lean burn combustor exit, has rarely been studied. For general HP turbine aerothermal designs, it is also of interest to understand how the behavior of a lean burn combustor traverses (hot streak and swirl) might contrast with those for rich burn combustion (largely hot streak only). In the present work, a computational study has been carried out on the aerothermal performance of a HP turbine stage under non-uniform temperature and velocity inlet profiles. The analyses are primarily conducted for two combined hot streak and swirl inlets, with opposite swirl directions. In addition, comparisons are made against a hot streak only case and a uniform inlet. The effects of three NGV shape configurations are investigated; namely, straight, compound lean (CL) and reverse compound lean (RCL). The present results show that there is a qualitative change in the roles played by heat transfer coefficient (HTC) and fluid driving (‘adiabatic wall’) temperature, Taw. It has been shown that the blade heat load distribution for a uniform inlet is dominated by HTC, whilst for a hot streak only case it is wholly influenced by Taw. However, in contrast to the hot streak only case, the case with a combined hot streak and swirl shows a role reversal with the HTC being dominant in determining the heat load. Additionally, it is seen that the swirling flow radially redistributes the hot fluid within the NGV passage considerably, leading to a much ‘flatter’ rotor inlet temperature profile compared to its hot streak only counterpart. Further, the rotor heat transfer characteristics for the cases with the combined traverses are shown to be strongly dependent on the NGV shaping and the inlet swirl direction, indicating the potential for future design space exploration. The present findings underline the need to clearly define relevant combustor exit temperature and velocity profiles when designing and optimizing NGVs for HP turbine aerothermal performance.

A Numerical Study of Secondary Flow in Axial Turbines With Application to Radial Transport of Hot Streaks

2000 ◽  
Author(s):  
Dilip Prasad ◽  
Gavin J. Hendricks
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Numerical Study ◽  
Angle Distribution ◽  
Turbine Stage ◽  
Radial Transport ◽  
Numerical Work ◽  
Flow Angle ◽  
Axial Turbines ◽  
Hot Streak

The flow field in a low-speed turbine stage with a uniform inlet total pressure is studied numerically. A circular hot streak is superposed on the vane inlet flow. In agreement with previous experimental and numerical work, it is observed that while the streak passes through the vane unaltered, significant radial transport occurs in the rotor. Furthermore, despite the unsteady nature of the flow field, the steady theory of Hawthorne (1974) is found to predict the radial transport velocity well. Making use of this theory, it is shown that the secondary vorticity in the rotor may be attributed to the effects of density stratification, the spatial variation of the vane exit flow angle and the relative eddy. It then follows that the extent of radial transport in the rotor may be influenced by altering the vane exit flow angle distribution. The present study examines one means by which this may be effected, viz., varying the vane twist across the span. It is shown that a “reverse” twist, wherein the flow angle at the vane exit is larger near the tip than it is at mid-span reduces the secondary flow (and consequently, radial transport) in the blade passage. On the other hand, “positive” twist, in which the vane exit flow angle decreases with span is found to markedly worsen the radial transport in the blade. It is to be noted that varying the vane twist is but one method to obtain the desired exit flow angle; possibilities for altering other aspects of the vane geometry also exist.

A Numerical Study of Secondary Flow in Axial Turbines With Application to Radial Transport of Hot Streaks

2000 ◽  
Vol 122 (4) ◽  
pp. 667-673 ◽  
Author(s):  
Dilip Prasad ◽  
Gavin J. Hendricks
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Numerical Study ◽  
Angle Distribution ◽  
Turbine Stage ◽  
Radial Transport ◽  
Numerical Work ◽  
Flow Angle ◽  
Axial Turbines ◽  
Hot Streak

The flow field in a low-speed turbine stage with a uniform inlet total pressure is studied numerically. A circular hot streak is superposed on the vane inlet flow. In agreement with previous experimental and numerical work, it is observed that while the streak passes through the vane unaltered, significant radial transport occurs in the rotor. Furthermore, despite the unsteady nature of the flow field, the steady theory of Hawthorne (1974) is found to predict the radial transport velocity well. Making use of this theory, it is shown that the secondary vorticity in the rotor may be attributed to the effects of density stratification, the spatial variation of the vane exit flow angle, and the relative eddy. It then follows that the extent of radial transport in the rotor may be influenced by altering the vane exit flow angle distribution. The present study examines one means by which this may be effected, viz., varying the vane twist across the span. It is shown that a “reverse” twist, wherein the flow angle at the vane exit is larger near the tip than it is at midspan, reduces the secondary flow (and consequently, radial transport) in the blade passage. On the other hand, “positive” twist, in which the vane exit flow angle decreases with span, is found to worsen the radial transport in the blade markedly. It is to be noted that varying the vane twist is but one method to obtain the desired exit flow angle; possibilities for altering other aspects of the vane geometry also exist. [S0889-504X(00)00104-5]

Influence of Hot Streak Circumferential Length-Scale in Transonic Turbine Stage

2004 ◽  
Author(s):  
L. He ◽  
V. Menshikova ◽  
B. R. Haller
Keyword(s):  
Heat Transfer ◽  
Computational Study ◽  
Guide Vane ◽  
Strong Dependence ◽  
Rotor Blades ◽  
Inlet Temperature ◽  
Turbine Stage ◽  
Blade Vibration ◽  
Nozzle Guide ◽  
Hot Streak

A computational study is carried out on the influence of turbine inlet temperature distortion (hot streak). The hot streak effects are examined from both aeromechanical (forced blade vibration) and aero-thermal (heat transfer) points of view. Computations are firstly carried out for a transonic HP turbine stage, and the steady and unsteady surface pressure results are compared with the corresponding experimental data. Subsequent analysis is carried out for hot-streaks with variable circumferential wavelength, corresponding to different numbers of combustion burners. The results show that the circumferential wavelength of the temperature distortion can significantly change unsteady forcing as well as the heat-transfer to rotor blades. In particular, when the hot-streak wavelength is the same as the nozzle guide vane (NGV) blade pitch, there is a strong dependence of the preferential heating characteristics on the relative clocking position between hot-streak and NGV blade. However, this clocking dependence is shown to be qualitatively weakened for the cases with fewer hot streaks with longer circumferential wavelengths.

Study of Hot Streak Effects in a Counter-Rotating Turbine

2001 ◽  
Author(s):  
L. C. Ji ◽  
J. Z. Xu ◽  
J. Chen
Keyword(s):  
High Pressure ◽  
Heat Load ◽  
Three Dimensional ◽  
High Pressure Turbine ◽  
Design And Optimization ◽  
Low Pressure Turbine ◽  
Second Stage ◽  
Euler Solver ◽  
Hot Streak ◽  
Turbine Design

Based on its convection nature, some influences of the hot streak on a 1+1 (with inter-blade vane) counter-rotating turbine are studied by using a three-dimensional (3D) unsteady Euler solver. Emphasis is laid on the hot streak effect to the blade heat load and the clocking effects between hot streak and blade rows. One temperature distortion magnitude, two spanwise and four tangential positions, four clocking locations between vanes of first and second stage are examined. Results show that the effect of the hot streak on a counter-rotating turbine is nearly the same as a conventional turbine. However, clocking between the hot streak and the vane of the high pressure turbine (HPT) exerts significant influences on the heat load of the whole HPT stage. Also, clocking between the HPT vane and the vane of the low pressure turbine (LPT) affects the heat load of the LPT greatly. These effects cannot be captured with the steady flow assumption. So time accurate simulation about the hot streak/blade interaction must be used as a basis for the turbine design and optimization.

Sign in / Sign up

Export Citation Format

Share Document