scholarly journals Influence of Intermediate Principal Stress on Undrained Behavior of Intact Clay under Pure Principal Stress Rotation

2013 ◽  
Vol 2013 ◽  
pp. 1-10 ◽  
Author(s):  
Jian Zhou ◽  
Jiajia Yan ◽  
Changjie Xu ◽  
Xiaonan Gong
Keyword(s):  
Pore Pressure ◽  
Principal Stress ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Clay ◽  
Shear Stiffness ◽  
Intermediate Principal Stress ◽  
Principal Stress Rotation ◽  
Stress Rotation

This study presents the accumulations of the excess pore water pressure and the deformation as well as the noncoaxial behavior of intact soft clay subjected to pure principal stress rotation. Series of tests were carried out by using a dynamic hollow cylinder apparatus to highlight the influence of intermediate principal stress parameterb. It was found that the rate of PWP evolution was greatly influenced byb, but the influence was not monotonous. Specimens under the conditionb= 0.75 had the highest accumulation of pore water pressure while under the conditionb= 0 had the strongest resistance to the pore pressure generation. PWP accumulated mainly in the first cycle. The failure of specimens under principal stress rotation was controlled by the strain other than the pore pressure. The shear stiffness decreased more quickly with higherbvalue. The direction of the principal strain increment was strongly dependent on the principal stress increment orientation and less influenced by thebvalue and the number of cycles.

scholarly journals A New Unified Solution for Deep Tunnels in Water-Rich Areas considering Pore Water Pressure

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Hao Fan ◽  
Lianguo Wang ◽  
Shuai Wang ◽  
Chongyang Jiang
Keyword(s):  
Principal Stress ◽  
Tangential Stress ◽  
Pore Water ◽  
Radial Stress ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Surface Displacement ◽  
Intermediate Principal Stress ◽  
Maximum Tangential Stress ◽  
Coulomb Criterion

Pore water pressure has an important influence on the stresses and deformation of the surrounding rock of deep tunnels in water-rich areas. In this study, a mechanical model for deep tunnels subjected to a nonuniform stress field in water-rich areas is developed. Considering the pore water pressure, a new unified solution for the stresses, postpeak zone radii, and surface displacement is derived based on a strain-softening model and the Mogi-Coulomb criterion. Through a case study, the effects of pore water pressure, intermediate principal stress, and residual cohesion on the stress distribution, postpeak zone radii, and surface displacement are also discussed. Results show that the tangential stresses are always larger than the radial stress. The radial stress presents a gradually increasing trend, while the tangential stress presents a trend of first increasing and then decreasing, and the maximum tangential stress appears at the interface between the elastic and plastic zones. As the pore water pressure increases, the postpeak zone radii and surface displacement increase. Because of the neglect of the intermediate principal stress in the Mohr-Coulomb criterion, the postpeak zone radii, surface displacement, and maximum tangential stress solved by the Mohr-Coulomb criterion are all larger than those solved by the Mogi-Coulomb criterion. Tunnels surrounded by rock masses with a higher residual cohesion experience lower postpeak zone radii and surface displacement. Data presented in this study provide an important theoretical basis for supporting the tunnels in water-rich areas.

scholarly journals Accumulation of Pore Pressure in a Soft Clay Seabed around a Suction Anchor Subjected to Cyclic Loads

2019 ◽  
Vol 7 (9) ◽  
pp. 308 ◽  
Author(s):  
Li ◽  
Chen ◽  
Hu ◽  
Wang ◽  
Liu
Keyword(s):  
Pore Pressure ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Kinematic Hardening ◽  
Water Pressure ◽  
Soft Clay ◽  
Cyclic Loads ◽  
Distribution Characteristics ◽  
Excess Pore Water Pressure ◽  
Excess Pore

A suction anchor is an appealing anchoring solution for floating production. However, the possible effects of residual pore pressure can be rarely found any report so far in term of the research and design. In this study, the residual pore pressure distribution characteristics around the suction anchor subjected to vertical cyclic loads are investigated in a soft clay seabed, and a three-dimensional damage-dependent bounding surface model is also proposed. This model adopts the combined isotropic-kinematic hardening rule to achieve isotropic hardening and kinematic hardening of the boundary surface. The proposed model is validated against triaxial tests on anisotropically consolidated saturated clays and normally consolidated saturated clays. The analytical results show that the excess pore water pressure accumulates primarily on the outside of the suction anchor, whereas negative pore water pressure mainly on the inside. The maximum values of both sides appear in the lower part of the seabed. According to the distribution characteristics of the residual pore pressure, a perforated anchor is proposed to reduce the accumulation of excess pore water pressure. A comparative study generally shows that the perforated anchor can effectively reduce the accumulation of excess pore water pressure.

Stress–strain pattern–based criterion to assess cyclic shear resistance of soil from laboratory element tests

2016 ◽  
Vol 53 (9) ◽  
pp. 1460-1473 ◽  
Author(s):  
Dharma Wijewickreme ◽  
Achala Soysa
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Shear Stiffness ◽  
Large Strains ◽  
Fundamental Parameter ◽  
Stress Strain ◽  
Cyclic Shear ◽  
Excess Pore Water Pressure ◽  
Excess Pore

The cyclic shear response of soils is commonly examined using undrained (or constant-volume) laboratory element tests conducted using triaxial and direct simple shear (DSS) devices. The cyclic resistance ratio (CRR) from these tests is expressed in terms of the number of cycles of loading to reach unacceptable performance that is defined in terms of the attainment of a certain excess pore-water pressure and (or) strain level. While strain accumulation is generally commensurate with excess pore-water pressure, the definition of unacceptable performance in laboratory tests based purely on cyclic strain criteria is not robust. The shear stiffness is a more fundamental parameter in describing engineering performance than the excess pore-water pressure alone or shear strain alone; so far, no criterion has considered shear stiffness to determine CRR. Data from cyclic DSS tests indicate consistent differences inherent in the patterns between the stress–strain loops at initial and later stages of cyclic loading; instead of relatively “smooth” stress–strain loops in the initial parts of loading, nonsmooth changes in incremental stiffness showing “kinks” are notable in the stress–strain loops at large strains. The point of pattern change in a stress–strain loop provides a meaningful basis to determine the CRR (based on unacceptable performance) in cyclic shear tests.

Study on Reinforce Saturated Soft Clay Foundation with Dynamic Consolidation by Drainage

2013 ◽  
Vol 438-439 ◽  
pp. 1171-1175
Author(s):  
Zhi Li Sui ◽  
Zhao Guang Li ◽  
Xu Peng Wang ◽  
Wen Li Li ◽  
Tie Jun Xu
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Clay ◽  
Soil Layer ◽  
Good Effect ◽  
Loading Test ◽  
Test Plate ◽  
Dynamic Consolidation ◽  
Saturated Soft Clay

Dynamic consolidation method has been widely used in improving soft land, but always inefficient to saturated soft clay land, which is hard to improve, and even leads to rubber soil. Dynamic and drain consolidation method will deal with it well, with drainage system, pore-water can be expelled instantly from saturated soft clay as impacting. The pore-water pressure and earth pressure test in construction, the standard penetration test, plate loading test, geotechnical test after construction, which are all effective methods for effect testing. There is a comprehensive detection through different depth of soil layer with different detecting means on construction site. The results show that improving saturated soft clay land with dynamic and drain consolidation method has obtained good effect, and the fruit can be guidance for such construction in the future.

scholarly journals Mechanical response and pore pressure generation in granular filters subjected to uniaxial cyclic loading

2018 ◽  
Vol 55 (12) ◽  
pp. 1756-1768
Author(s):  
Jahanzaib Israr ◽  
Buddhima Indraratna
Keyword(s):  
Cyclic Loading ◽  
Pore Pressure ◽  
Pore Water ◽  
Mechanical Response ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Internal Erosion ◽  
Excess Pore Water Pressure ◽  
Excess Pore

This paper presents results from a series of piping tests carried out on a selected range of granular filters under static and cyclic loading conditions. The mechanical response of filters subjected to cyclic loading could be characterized in three distinct phases; namely, (I) pre-shakedown, (II) post-shakedown, and (III) post-critical (i.e., the occurrence of internal erosion). All the permanent geomechanical changes such, as erosion, permeability variations, and axial strain developments, took place during phases I and III, while the specimen response remained purely elastic during phase II. The post-critical occurrence of erosion incurred significant settlement that may not be tolerable for high-speed railway substructures. The analysis revealed that a cyclic load would induce excess pore-water pressure, which, in corroboration with steady seepage forces and agitation due to dynamic loading, could then cause internal erosion of fines from the specimens. The resulting excess pore pressure is a direct function of the axial strain due to cyclic densification, as well as the loading frequency and reduction in permeability. A model based on strain energy is proposed to quantify the excess pore-water pressure, and subsequently validated using current and existing test results from published studies.

scholarly journals Effect of Wetting-Drying Cycle on the Deformation and Seepage Behaviors of Rock Masses around a Tunnel

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Qingzhen Guo ◽  
Haijian Su ◽  
Hongwen Jing ◽  
Wenxin Zhu
Keyword(s):  
Rock Mass ◽  
Principal Stress ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Inrush ◽  
Surrounding Rock ◽  
Tunnel Excavation ◽  
Cycle Number ◽  
Simulation Results

Water inrush caused by the wetting-drying cycle is a difficult problem in tunnel excavation. To investigate the effect of the wetting-drying cycle on the stability of the tunnel surrounding rock, physical experiments and numerical simulations regarding the process of tunnel excavation with different wetting-drying cycle numbers were performed in this study. The evolutions of stress, displacement, and pore water pressure were analyzed. With the increase in cycle number, the pore water pressure, vertical stress, and top-bottom approach of the tunnel surrounding rock increase gradually. And the increasing process could be divided into three stages: slightly increasing stage, slowly increasing stage, and sharply increasing stage, respectively. The failure process of the surrounding rock under the wetting-drying cycle gradually occurs from the roof to side wall, while the baseplate changes slightly. The simulation results showed that the maximum principal stress in the surrounding rock mass of the tunnel increases, while the minimum principal stress decreases. Furthermore, the displacement of the rock mass decreases gradually with the increasing distance from the tunnel surface. By comparing the simulation results with the experimental results, well consistency is shown. The results in this study can provide helpful references for the safe excavation and scientific design of a tunnel under the wetting-drying cycle.

Experimental verification of the theory of consolidation for unsaturated soils

1995 ◽  
Vol 32 (5) ◽  
pp. 749-766 ◽  
Author(s):  
Harianto Rahardjo ◽  
Delwyn G. Fredlund
Keyword(s):  
Water Content ◽  
Pore Pressure ◽  
Pore Water ◽  
Unsaturated Soils ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Matric Suction ◽  
Water Volume ◽  
Loading Tests ◽  
Undrained Loading

An experimental program was designed to study the behavior of unsaturated soils during undrained loading and consolidation. A Ko cylinder was designed and built for the testing program. Simultaneous measurements of pore-air and pore-water pressures could be made throughout a soil specimen using this Ko cylinder. Four types of tests were performed on a silty sand. These are (1) undrained loading tests where both the air and water are not allowed to drain, (2) constant water content tests where only the water phase is not allowed to drain, (3) consolidation tests where both the air and water phases are allowed to drain, and (4) increasing matric suction tests. Undrained loading tests or constant water content loading tests were conducted for measuring the pore pressure parameters for the unsaturated soil. Drained tests consisting of either consolidation tests or increasing matric suction tests were conducted to study the pore pressure distribution and volume change behavior throughout an unsaturated soil during a transient process. The experimental pore pressure parameters obtained from the undrained loadings and constant water content leadings agreed reasonably well with theory. The pore-air pressure was found to dissipate instantaneously when the air phase is continuous. The pore-water pressure dissipation during the consolidation test was found to be faster than the pore-water pressure decrease during the increasing matric suction test. The differing rates of dissipation were attributed to the different coefficients of water volume change for each of the tests. The water volume changes during the consolidation test were considerably smaller than the water volume changes during the increasing matric suction tests for the same increment of pressure change. Key words : consolidation, Ko loading, matric suction, pore-air pressures, pore-water pressures, unsaturated soils

Sign in / Sign up

Export Citation Format

Share Document