scholarly journals Effect of Wetting-Drying Cycle on the Deformation and Seepage Behaviors of Rock Masses around a Tunnel

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Qingzhen Guo ◽  
Haijian Su ◽  
Hongwen Jing ◽  
Wenxin Zhu
Keyword(s):  
Rock Mass ◽  
Principal Stress ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Inrush ◽  
Surrounding Rock ◽  
Tunnel Excavation ◽  
Cycle Number ◽  
Simulation Results

Water inrush caused by the wetting-drying cycle is a difficult problem in tunnel excavation. To investigate the effect of the wetting-drying cycle on the stability of the tunnel surrounding rock, physical experiments and numerical simulations regarding the process of tunnel excavation with different wetting-drying cycle numbers were performed in this study. The evolutions of stress, displacement, and pore water pressure were analyzed. With the increase in cycle number, the pore water pressure, vertical stress, and top-bottom approach of the tunnel surrounding rock increase gradually. And the increasing process could be divided into three stages: slightly increasing stage, slowly increasing stage, and sharply increasing stage, respectively. The failure process of the surrounding rock under the wetting-drying cycle gradually occurs from the roof to side wall, while the baseplate changes slightly. The simulation results showed that the maximum principal stress in the surrounding rock mass of the tunnel increases, while the minimum principal stress decreases. Furthermore, the displacement of the rock mass decreases gradually with the increasing distance from the tunnel surface. By comparing the simulation results with the experimental results, well consistency is shown. The results in this study can provide helpful references for the safe excavation and scientific design of a tunnel under the wetting-drying cycle.

scholarly journals Mechanism of Fracturing in Shaft Lining Caused by High-Pressure Pore Water in Stable Rock Strata

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Jihuan Han ◽  
Jiuqun Zou ◽  
Weihao Yang ◽  
Chenchen Hu
Keyword(s):  
High Pressure ◽  
Rock Mass ◽  
Pore Water ◽  
Expansion Coefficient ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Surrounding Rock ◽  
Shaft Lining ◽  
Rock Strata ◽  
Expansion Effect

With the increase in shaft depth, the problem of cracks and leakage in single-layer concrete lining in porous water-rich stable rock strata has become increasingly clear, in which case the mechanism of fracturing in shaft lining remains unclear. Considering that the increase in pore water pressure can cause rock mass expansion, this paper presents the concept of hydraulic expansion coefficient. First, a cubic model containing spherical pores is established for studying hydraulic expansion, and the ANSYS numerical simulation, a finite element numerical method, was used for calculating the volume change of the model under the pore water pressure. By means of the multivariate nonlinear regression method, the regression equation of the hydraulic expansion coefficient is obtained. Second, based on the hydraulic expansion effect on the rock mass, an interaction model of pore water pressure–porous rock–shaft lining is established and further solved. Consequently, the mechanism of fracturing in shaft lining caused by high-pressure pore water is revealed. The results show that the hydraulic expansion effect on the surrounding rock increases with its porosity and decreases with its elastic modulus and Poisson’s ratio; the surrounding rock expansion caused by the change in pore water pressure can result in the outer edge of the lining peeling off from the surrounding rock and tensile fracturing at the inner edge. Therefore, the results have a considerable guiding significance for designing shaft lining through porous water-rich rock strata.

scholarly journals Elastic-Plastic Numerical Analysis of Tunnel Stability Based on the Closest Point Projection Method Considering the Effect of Water Pressure

2016 ◽  
Vol 2016 ◽  
pp. 1-12 ◽  
Author(s):  
Zhan-ping Song ◽  
Ten-tian Yang ◽  
An-nan Jiang
Keyword(s):  
Rock Mass ◽  
Numerical Analysis ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Surrounding Rock ◽  
Tunnel Stability ◽  
Elastic Plastic ◽  
Closest Point Projection ◽  
Point Projection

To study the tunnel stability at various static water pressures and determine the mechanical properties and deformation behavior of surrounding rock, a modified effective stress formula was introduced into a numerical integration algorithm of elastic-plastic constitutive equation, that is, closest point projection method (CPPM). Taking the effects of water pressure and seepage into account, a CPPM-based formula was derived and a CPPM algorithm based on Drucker-Prager yield criterion considering the effect of pore water pressure was provided. On this basis, a CPPM-based elastic-plastic numerical analysis program considering pore water pressure was developed, which can be applied in the engineering of tunnels and other underground structures. The algorithm can accurately take the effects of groundwater on stability of surrounding rock mass into account and it can show the more pronounced effect of pore water pressure on stress, deformation, and the plastic zone in a tunnel. The stability of water flooding in Fusong tunnel was systematically analyzed using the developed program. The analysis results showed that the existence of groundwater seepage under tunnel construction will give rise to stress redistribution in the surrounding rock mass. Pore water pressure has a significant effect on the surrounding rock mass.

scholarly journals Mechanisms of Crack Initiation and Propagation in Dense Linear Multihole Directional Hydraulic Fracturing

2019 ◽  
Vol 2019 ◽  
pp. 1-15
Author(s):  
Jiangwei Liu ◽  
Changyou Liu ◽  
Qiangling Yao
Keyword(s):  
Rock Mass ◽  
Crack Initiation ◽  
Hydraulic Fracturing ◽  
Principal Stress ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Crack Initiation And Propagation ◽  
Initiation And Propagation ◽  
Coal Rock

Artificially fracturing coal-rock mass serves to form break lines therein, which is related to the distribution of cracked boreholes. For this reason, we use physical experiments and numerical simulations to study the crack initiation and propagation characteristics of dense linear multihole drilling of fractured coal-rock mass. The results indicate that only in the area between the first and last boreholes can hydraulic fracturing be controlled by dense linear multihole expansion along the direction of the borehole line; in addition, no directional fracturing occurs outside the drilling section. Upon increasing parameters such as the included angle θ between the drilling arrangement line and the maximum principal stress σ1 direction, the drilling spacing D, the difference Δσ in principal stress, etc., the effect of directional fracture is gradually weakened, and the hydraulic fractures reveal three typical cracking modes: cracking along the borehole line, bidirectional cracking (along the borehole line and perpendicular to the minimum principal stress σ3), and cracking perpendicular to σ3. Five propagation modes also appear in sequence: propagating along borehole line, step-like propagation, S-shaped propagation, bidirectional propagation (along the borehole line and perpendicular to σ3), and propagation perpendicular to σ3. Based on these results, we report the typical characteristics of three-dimensional crack propagation and discuss the influence of the gradient of pore water pressure. The results show clearly that crack initiation and propagation are affected by both the geostress field and the pore water pressure. The pore water pressure will exhibit a circular-local contact-to-integral process during crack initiation and expansion. When multiple cracks approach, the superposition of pore water pressure at the tip of the two cracks increases the damage to the coal rock, which causes crack reorientation and intersection.

scholarly journals Analysis on Water Inrush Process of Tunnel with Large Buried Depth and High Water Pressure

Processes ◽  
2019 ◽  
Vol 7 (3) ◽  
pp. 134 ◽  
Author(s):  
Weimin Yang ◽  
Zhongdong Fang ◽  
Hao Wang ◽  
Liping Li ◽  
Shaoshuai Shi ◽  
...  
Keyword(s):  
High Pressure ◽  
Model Test ◽  
Water Pressure ◽  
Water Inrush ◽  
High Water ◽  
Surrounding Rock ◽  
Karst Cave ◽  
Tunnel Excavation ◽  
Pressure Water ◽  
High Water Pressure

In order to explore the catastrophic evolution process for karst cave water inrush in large buried depth and high water pressure tunnels, a model test system was developed, and a similar fluid–solid coupled material was found. A model of the catastrophic evolution of water inrush was developed based on the Xiema Tunnel, and the experimental section was simulated using the finite element method. By analyzing the interaction between groundwater and the surrounding rocks during tunnel excavation, the law of occurrence of water inrush disaster was summarized. The water inrush process of a karst cave containing high-pressure water was divided into three stages: the production of a water flowing fracture, the expansion of the water flowing fracture, and the connection of the water flowing fracture. The main cause of water inrush in karst caves is the penetration and weakening of high-pressure water on the surrounding rock. This effect is becoming more and more obvious as tunnel excavation progresses. The numerical simulation results showed that the outburst prevention thickness of the surrounding rock is 4.5 m, and that of the model test result is 5 m. Thus, the results of the two methods are relatively close to each other. This work is important for studying the impact of groundwater on underground engineering, and it is of great significance to avoid water inrush in tunnels.

Study of Variation of Soil Stress State Based on the Curve of Normalized Strain- Pore Water Pressure

2013 ◽  
Vol 275-277 ◽  
pp. 295-298
Author(s):  
Gang Yang ◽  
Qing Yang ◽  
Wen Hua Liu
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Cyclic Stress ◽  
Cyclic Stress Ratio ◽  
Cycle Number ◽  
Soil Stress ◽  
Critical Cyclic Stress Ratio ◽  
Versus Strain

The cyclic behavior of normally consolidated silty clays was investigated by conducting a series of cyclic simple shear tests on one-dimensionally and isotropically consolidated reconstituted samples. The critical cyclic stress ratio was obtained by the normalized axial strain. Based on hysteretic curve of pore water pressure versus strain, dynamic characteristics of silty clay were investigated. The results showed that with increasing of cyclic loading, soil stress state can be divided into steady state, critical state and failure state based on the critical cyclic stress ratio. The hysteresis curve of pore water pressure versus strain was divided into two parts by cross point A. Compared with two parts, the variation law was obtained. When the upper part area was bigger than the lower part area, pore water pressure and axial strain continuously increase with cycle number; when the upper part area was smaller than the lower part area, pore water pressure and axial strain tended to be steady with cycle number.

scholarly journals Theoretical Analysis of Safety Thickness of the Water-Resistant Rock Mass of Karst Tunnel Face Taking Into Account Seepage Effect

2021 ◽  
Author(s):  
Jiaqi GUO ◽  
Wenlong Wu ◽  
Xiliang Liu ◽  
Xin Huang ◽  
Zhengguo Zhu
Keyword(s):  
Rock Mass ◽  
Influencing Factors ◽  
Water Pressure ◽  
Water Inrush ◽  
Surrounding Rock ◽  
Karst Water ◽  
Seepage Force ◽  
Karst Tunnel ◽  
Tunnel Face ◽  
Safety Thickness

Abstract This paper took into account the adverse influence of the karst water seepage effect on the water-resistant rock mass. Based on the upper-bound theorem of limit analysis and the Hoek-Brown failure criterion, through a series of formula derivation, the expression of critical safety thickness of water-resistant rock mass of karst tunnel face was finally obtained. The paper carried out a feasibility analysis, an analysis of influencing factors and a comparative analysis with previous related research achievements of this method. The results showed that: (1) With the decrease of surrounding rock grade, the safety thickness of water-resistant rock mass gradually increased, and the safety thickness of surrounding rock at all grades remained within a reasonable range. (2) The safety thickness decreased as the compressive strength, the tensile strength and parameter A increased, and it increased as the karst water pressure, the tunnel excavation height, and parameter B increased. (3) The change trend of the safety thickness with the influencing factors was completely consistent under the two conditions of considering and without the seepage effect, and the safety thickness with considering the seepage force was greater than that without considering the seepage force. Taking the Yunwushan tunnel of Yiwan railway as an example, the critical safety thickness of the water-resistant rock mass was calculated and the calculated value was in good coincidence with the safety thickness adopted in the actual project. The research results are of great significance to prevent the occurrence of high pressure filling karst geological disasters such as water inrush in tunnels.

scholarly journals Experimental Study on the Failure Mechanism of Tunnel Surrounding Rock under Different Groundwater Seepage Paths

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
Yingchao Wang ◽  
Yang Liu ◽  
Yongliang Li ◽  
Wen Jiang ◽  
Yueming Wang
Keyword(s):  
Failure Mechanism ◽  
Water Flow ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Flow Rate ◽  
Surrounding Rock ◽  
Tunnel Engineering ◽  
Measuring Point ◽  
Groundwater Seepage

The influence of groundwater on tunnel engineering is very complicated. Due to the complexity of water flow water pressure transfer and uncertain defects in the stratum, all of which are key factors with regard to the design of tunnel engineering. Therefore, the variation of surrounding rock during excavation and the deformation and failure of soft surrounding rock under different seepage paths of underground water after excavation systematically. Experimental results showed that the stress change of surrounding rock caused by tunnel excavation can be divided into 3 stages: stress redistribution, stress adjustment, and stress rebalancing. In the process of water pressure loading, water flow rate is closely related to the experimental phenomenon. The between stable loading water pressure pore water pressure of the tunnel surrounding rock and the distance from the measuring point to the edge of the tunnel obey the exponential function of the decreasing growth gradient. With the increase of loading pressure, the pore water pressure and stress at the top of the tunnel increase, and the coupling of stress field and seepage field on both sides of surrounding rock more and more intense. The failure process of the tunnel can be divided into 6 stages according to the damage degree. The final failure pattern of the surrounding rock of the tunnel is mainly determined by the disturbed area of excavation. The arched failure area and the collapse-through failure area are composed of three regions. The surrounding rock is characterized by a dynamic pressure arch in the process of seepage failure, but it is more prone to collapse failure at low water pressure. The results of this study are the progressive failure mechanism of tunnel under different groundwater seepage paths and would be of great significance to the prevention of long-range disasters.

scholarly journals Numerical Simulation of Seepage and Deformation in Excavation of a Deep Foundation Pit under Water-Rich Fractured Intrusive Rock

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-10
Author(s):  
Changfeng Yuan ◽  
Zhenhui Hu ◽  
Zhen Zhu ◽  
Zijin Yuan ◽  
Yanxiang Fan ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Inrush ◽  
Risk Level ◽  
Silty Clay ◽  
Deep Foundation ◽  
Foundation Pit ◽  
Deep Foundation Pit

Water is one of the major risk sources in the excavation of deep-large foundation pits in a water-rich area. The presence of intrusive broken diorite porphyrite in the stratum aggravates the risk level of deep foundation pits. Based on a geological survey report and design documents of parameter information, MIDAS/GTS software was used to perform the numerical simulation of an engineering example of a deep foundation pit project of ultradeep and water-rich intrusion into the broken rock station of subway line 4 in a city. The simulation results show the characteristics of seepage path evolution, seepage aggregation areas and points, and the effect of seepage on the deformation of a deep foundation pit during the whole construction of this deep foundation pit. The results show that with the precipitation-excavation of the deep foundation pit, the pore water pressure at the bottom of the foundation pit follows a distribution of three “concave” shapes. High-permeability pressure zones are found around the foundation pit, intruding broken diorite porphyrite zones, and middle coarse sand zones. With further excavation of the foundation pit, the seepage pressure in the middle part of the foundation pit gradually decreases, and the two “concave” distributions in the middle gradually merge together. After excavation to the bottom of the pit, the pore water pressure at the bottom is distributed in two asymmetrical “concave” shapes, and the maximum peak of pore water pressure is found at the intrusion of fractured porphyrites prone to water inrush. The four corners of the foundation pit are prone to form seepage accumulation zones; therefore, suffosion and piping zones are formed. The surface settlement caused by excavation is found to be the largest along the longitudinal axis of the deep foundation pit, whereas the largest deformation is found near the foundation pit side in the horizontal axis direction of the foundation pit. With the excavation of the deep foundation pit, the diaphragm wall converges to the foundation pit with the maximum deformation reaching about 25 mm. After the first precipitation-excavation of the deep foundation pit to the silty clay and the bottom of the pit with the largest uplift, with further precipitation-excavation of the deep foundation pit, the uplift at the bottom of the deep foundation pit changes only slightly.

scholarly journals Study on the Variation Rule and Characteristics of Pore Water Pressure in the Failure Process of Saturated Rock

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Yuezheng Zhang
Keyword(s):  
Rock Mass ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Failure Process ◽  
Engineering Practice ◽  
Surrounding Area ◽  
Saturated Rock ◽  
In Situ Conditions ◽  
Variation Rule

With the development of tunnels and other engineering constructions into the deep strata, rock masses are more prone to dynamic damage such as rock bursts under in situ conditions and excavation disturbances. The pore water in the rock mass will produce pressure changes during this process. According to the relationship between the change of pore water pressure and the development of rock mass damage, the variation rule and precursor characteristics of pore water pressure in the process of rock mass failure can be found. In this paper, through mechanical analysis, the evolution law of pore water pressure during the failure process of saturated rock is obtained. The study found that, in the process of rock failure, the pore water pressure presents three stages of linear growth, transition, and decrease. The rise and fall of pore water pressure are closely related to rock damage and influence each other. Through the observation of pore water pressure during coal mining, it is found that the coseismic effect of pore water pressure is significant. It is proved that there is a close correlation between the evolution of the stress field in the surrounding area of the stope and the change of pore water pressure in the surrounding area under the effect of mining disturbance. During the engineering practice, dynamic monitoring can be carried out on the change of pore water pressure inside the rock mass according to the law, and the precursor information of rock mass instability and failure can be explored.

Sign in / Sign up

Export Citation Format

Share Document