scholarly journals Numerical Simulation of Residual Oil Flooded by Polymer Solution in Microchannels

Geofluids ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Yang Liu ◽  
Jiawei Fan ◽  
Lili Liu ◽  
Shuren Yang
Keyword(s):  
Contact Angle ◽  
Polymer Solution ◽  
Oil Recovery ◽  
Wetting Angle ◽  
Polymer Flooding ◽  
Residual Oil ◽  
Receding Contact ◽  
Advancing Contact Angle ◽  
Receding Contact Angle ◽  
The Impact

This paper establishes a flow equation using non-Newtonian fluid mechanics and defines the deformation of residual oil using numerical computation in order to conduct a study on the flow law of residual oil in microchannels of rock during polymer flooding, the influence of flooding fluid elasticity on the deformation of residual oil, and flooding mechanism of viscoelastic displacing fluid. Computation shows that advancing contact angle increases and receding contact angle decreases as the viscosity ratio decreases. The higher elasticity of polymer solution with higher concentration or molecular weight leads to significantly more obvious deformation of residual oil and benefits migration and stripping of residual oil. The impact of the initial wetting angle of residual oil film on deformation is analyzed. A smaller initial wetting angle corresponds to a bigger change of advancing contact angle and smaller change of receding contact angle. A better understanding of the flooding process is gained via a study on residual oil deformation in polymer flooding. Consequently, oil flooding efficiency and oil recovery can be enhanced. This is the hydrodynamic mechanism of enhanced oil recovery (EOR) by polymer flooding.

scholarly journals Differences of microscopic seepage mechanisms of water flooding and polymer flooding and prediction models of final oil recovery for conglomerate reservoir

2019 ◽  
Vol 74 ◽  
pp. 13
Author(s):  
Fengqi Tan ◽  
Changfu Xu ◽  
Yuliang Zhang ◽  
Gang Luo ◽  
Yukun Chen ◽  
...  
Keyword(s):  
Pore Structure ◽  
Polymer Solution ◽  
Oil Recovery ◽  
Particle Surface ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Residual Oil ◽  
Displacement Efficiency ◽  
Oil Saturation ◽  
Oil Displacement Efficiency

The special sedimentary environments of conglomerate reservoir lead to pore structure characteristics of complex modal, and the reservoir seepage system is mainly in the “sparse reticular-non reticular” flow pattern. As a result, the study on microscopic seepage mechanism of water flooding and polymer flooding and their differences becomes the complex part and key to enhance oil recovery. In this paper, the actual core samples from conglomerate reservoir in Karamay oilfield are selected as research objects to explore microscopic seepage mechanisms of water flooding and polymer flooding for hydrophilic rock as well as lipophilic rock by applying the Computed Tomography (CT) scanning technology. After that, the final oil recovery models of conglomerate reservoir are established in two displacement methods based on the influence analysis of oil displacement efficiency. Experimental results show that the seepage mechanisms of water flooding and polymer flooding for hydrophilic rock are all mainly “crawling” displacement along the rock surface while the weak lipophilic rocks are all mainly “inrushing” displacement along pore central. Due to the different seepage mechanisms among the water flooding and the polymer flooding, the residual oil remains in hydrophilic rock after water flooding process is mainly distributed in fine throats and pore interchange. These residual oil are cut into small droplets under the influence of polymer solution with stronger shearing drag effect. Then, those small droplets pass well through narrow throats and move forward along with the polymer solution flow, which makes enhancing oil recovery to be possible. The residual oil in weak lipophilic rock after water flooding mainly distributed on the rock particle surface and formed oil film and fine pore-throat. The polymer solution with stronger shear stress makes these oil films to carry away from particle surface in two ways such as bridge connection and forming oil silk. Because of the essential attributes differences between polymer solution and injection water solution, the impact of Complex Modal Pore Structure (CMPS) on the polymer solution displacement and seepage is much smaller than on water flooding solution. Therefore, for the two types of conglomerate rocks with different wettability, the pore structure is the main controlling factor of water flooding efficiency, while reservoir properties oil saturation, and other factors have smaller influence on flooding efficiency although the polymer flooding efficiency has a good correlation with remaining oil saturation after water flooding. Based on the analysis on oil displacement efficiency factors, the parameters of water flooding index and remaining oil saturation after water flooding are used to establish respectively calculation models of oil recovery in water flooding stage and polymer flooding stage for conglomerate reservoir. These models are able to calculate the oil recovery values of this area controlled by single well control, and further to determine the oil recovery of whole reservoir in different displacement stages by leveraging interpolation simulation methods, thereby providing more accurate geological parameters for the fine design of displacement oil program.

The Surface Modification with Fluorocarbon Thin Films for the Prevention of Stiction in Mems

1998 ◽  
Vol 518 ◽  
Author(s):  
Sang-Ho Lee ◽  
Myong-Jong Kwon ◽  
Jin-Goo Park ◽  
Yong-Kweon Kim ◽  
Hyung-Jae Shin
Keyword(s):  
Contact Angle ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Fluorocarbon Films ◽  
Perfluorodecanoic Acid ◽  
Large Hysteresis ◽  
Static Contact ◽  
Receding Contact ◽  
Highly Hydrophobic ◽  
Receding Contact Angle

AbstractHighly hydrophobic fluorocarbon films were prepared by the vapor phase (VP) deposition method in a vacuum chamber using both liquid (3M's FC40, FC722) and solid sources (perfluorodecanoic acid (CF3(CF2)8COOH), perfluorododecane (C12F26)) on Al, Si and oxide coated wafers. The highest static contact angles of water were measured on films deposited on aluminum substrate. But relatively lower contact angles were obtained on the films on Si and oxide wafers. The advancing and receding contact angle analysis using a captive drop method showed a large contact angle hysteresis (ΔH) on the VP deposited fluorocarbon films. AFM study showed poor film coverage on the surface with large hysteresis. FTIR-ATR analysis positively revealed the stretching band of CF2 groups on the VP deposited substrates. The thermal stability of films was measured at 150°C in air and nitrogen atmospheres as a function of time. The rapid decrease of contact angles was observed on VP deposited FC and PFDA films in air. However, no decrease of contact angle on them was observed in N2.

Relationship between Residual Saturations and Wettability using Pore-Network Modeling

2021 ◽  
Author(s):  
Prakash Purswani ◽  
Russell T. Johns ◽  
Zuleima T. Karpyn
Keyword(s):  
Contact Angle ◽  
Oil Recovery ◽  
Network Modeling ◽  
Pore Network ◽  
Residual Oil ◽  
Residual Saturation ◽  
Oil Saturation ◽  
Pore Network Modeling ◽  
Residual Oil Saturation ◽  
Eor Processes

Abstract The relationship between residual saturation and wettability is critical for modeling enhanced oil recovery (EOR) processes. The wetting state of a core is often quantified through Amott indices, which are estimated from the ratio of the saturation fraction that flows spontaneously to the total saturation change that occurs due to spontaneous flow and forced injection. Coreflooding experiments have shown that residual oil saturation trends against wettability indices typically show a minimum around mixed-wet conditions. Amott indices, however, provides an average measure of wettability (contact angle), which are intrinsically dependent on a variety of factors such as the initial oil saturation, aging conditions, etc. Thus, the use of Amott indices could potentially cloud the observed trends of residual saturation with wettability. Using pore network modeling (PNM), we show that residual oil saturation varies monotonically with the contact angle, which is a direct measure of wettability. That is, for fixed initial oil saturation, the residual oil saturation decreases monotonically as the reservoir becomes more water-wet (decreasing contact angle). Further, calculation of Amott indices for the PNM data sets show that a plot of the residual oil saturation versus Amott indices also shows this monotonic trend, but only if the initial oil saturation is kept fixed. Thus, for the cases presented here, we show that there is no minimum residual saturation at mixed-wet conditions as wettability changes. This can have important implications for low salinity waterflooding or other EOR processes where wettability is altered.

scholarly journals Effect of Non-Newtonian Flow on Polymer Flooding in Heavy Oil Reservoirs

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1225 ◽  
Author(s):  
Xiankang Xin ◽  
Gaoming Yu ◽  
Zhangxin Chen ◽  
Keliu Wu ◽  
Xiaohu Dong ◽  
...  
Keyword(s):  
Porous Media ◽  
Polymer Solution ◽  
Oil Recovery ◽  
Heavy Oil ◽  
Flow Behavior ◽  
Polymer Flooding ◽  
Oil Reservoirs ◽  
Flow In Porous Media ◽  
Newtonian Flow ◽  
Heavy Oil Reservoirs

The flow of polymer solution and heavy oil in porous media is critical for polymer flooding in heavy oil reservoirs because it significantly determines the polymer enhanced oil recovery (EOR) and polymer flooding efficiency in heavy oil reservoirs. In this paper, physical experiments and numerical simulations were both applied to investigate the flow of partially hydrolyzed polyacrylamide (HPAM) solution and heavy oil, and their effects on polymer flooding in heavy oil reservoirs. First, physical experiments determined the rheology of the polymer solution and heavy oil and their flow in porous media. Then, a new mathematical model was proposed, and an in-house three-dimensional (3D) two-phase polymer flooding simulator was designed considering the non-Newtonian flow. The designed simulator was validated by comparing its results with those obtained from commercial software and typical polymer flooding experiments. The developed simulator was further applied to investigate the non-Newtonian flow in polymer flooding. The experimental results demonstrated that the flow behavior index of the polymer solution is 0.3655, showing a shear thinning; and heavy oil is a type of Bingham fluid that overcomes a threshold pressure gradient (TPG) to flow in porous media. Furthermore, the validation of the designed simulator was confirmed to possess high accuracy and reliability. According to its simulation results, the decreases of 1.66% and 2.49% in oil recovery are caused by the difference between 0.18 and 1 in the polymer solution flow behavior indexes of the pure polymer flooding (PPF) and typical polymer flooding (TPF), respectively. Moreover, for heavy oil, considering a TPG of 20 times greater than its original value, the oil recoveries of PPF and TPF are reduced by 0.01% and 5.77%, respectively. Furthermore, the combined effect of shear thinning and a threshold pressure gradient results in a greater decrease in oil recovery, with 1.74% and 8.35% for PPF and TPF, respectively. Thus, the non-Newtonian flow has a hugely adverse impact on the performance of polymer flooding in heavy oil reservoirs.

scholarly journals SURFACTANT-POLYMER FLOODING PERFORMANCE IN HETEROGENEOUS TWO-LAYERED POROUS MEDIA

2011 ◽  
Vol 12 (1) ◽  
pp. 31-38 ◽  
Author(s):  
Muhammad Taufiq Fathaddin ◽  
Asri Nugrahanti ◽  
Putri Nurizatulshira Buang ◽  
Khaled Abdalla Elraies
Keyword(s):  
Porous Media ◽  
Oil Recovery ◽  
Polymer Flooding ◽  
Water Flooding ◽  
Residual Oil ◽  
Oil Saturation ◽  
Reservoir Heterogeneity ◽  
Residual Oil Saturation ◽  
Layered Porous Media ◽  
Multiple Porosity

In this paper, simulation study was conducted to investigate the effect of spatial heterogeneity of multiple porosity fields on oil recovery, residual oil and microemulsion saturation. The generated porosity fields were applied into UTCHEM for simulating surfactant-polymer flooding in heterogeneous two-layered porous media. From the analysis, surfactant-polymer flooding was more sensitive than water flooding to the spatial distribution of multiple porosity fields. Residual oil saturation in upper and lower layers after water and polymer flooding was about the same with the reservoir heterogeneity. On the other hand, residual oil saturation in the two layers after surfactant-polymer flooding became more unequal as surfactant concentration increased. Surfactant-polymer flooding had higher oil recovery than water and polymer flooding within the range studied. The variation of oil recovery due to the reservoir heterogeneity was under 9.2%.

Sign in / Sign up

Export Citation Format

Share Document