scholarly journals Studies on Optimal Strategy to Adopt Nuclear Power Plants into Saudi Arabian Energy System Using MESSAGE Tool

2021 ◽  
Vol 2021 ◽  
pp. 1-26
Author(s):  
Shadwan M. M. Esmail ◽  
Jae Hak Cheong
Keyword(s):  
Saudi Arabia ◽  
Optimal Strategy ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Energy System ◽  
Strategic Options ◽  
Electricity Shortage

An optimal long-term electric power strategy for Saudi Arabia to adopt nuclear power was evaluated using the MESSAGE tool. Saudi Arabia is predicted to experience an electricity shortage by 2025 with the present energy system. This electricity shortage could be postponed until 2035 by rehabilitating the existing power plants. The MESSAGE model predicts that adopting a combination of renewable (i.e., solar and wind), advanced traditional power (i.e., gas turbine, steam, and combined cycle), and nuclear technologies is the most competitive future strategy to supply 43.7%, 41.6%, and 3.8%, respectively, of Saudi Arabia’s electricity needs by 2050. This paper proposes an optimal strategy for adopting nuclear power. The nuclear capacity of three scenarios was evaluated: a single APR-1400 nuclear reactor, a single SMART-100 nuclear reactor, and a combination of these two reactors. The results of this study indicate that the highest nuclear capacity was achieved by the combination of the APR-1400 and SMART-100 reactors followed by the single APR-1400 reactor and then the single SMART-100 reactor. However, the single G4ECONS nuclear reactor shows a higher capacity than the single APR-1400 reactor in other evaluated scenarios. The combined reactor strategy may be the most feasible option if the capital cost of a first-of-a-kind SMART-100 reactor is reduced by 62.3%. The cost reductions result from including factors like the time required to build the nuclear power plants in the MESSAGE tool calculation. Also, CO2 taxation will increase nuclear power’s feasibility in the Saudi Arabian energy system. However, the share of renewable energy is predicted to be more affected by the taxation of CO2. In this study, the proposed approach can provide more flexible strategic options for countries embarking on nuclear energy. These flexible strategic options can optimize their national energy mix for long-term planning.

scholarly journals Influence of irradiation on the dynamics of changes in the mechanical properties of the nuclear reactor vessel

2018 ◽  
Vol 226 ◽  
pp. 01024
Author(s):  
Yulia S. Bakhracheva
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Automatic Monitoring ◽  
Energy System ◽  
Reactor Vessel ◽  
Reactor Steels ◽  
Irradiation Level ◽  
Emergency Systems

Nuclear power plants are important generating units of the energy system worldwide. In the normal mode, nuclear power plants are absolutely safe, but emergency systems with radiation emissions have a devastating impact on the environment and public health. Despite the introduction of technologies and automatic monitoring systems, the threat of a potentially dangerous situation remains. The reactor vessel is the main object of activities to ensure the safety of nuclear power plants. One of the problems of ensuring the safety of nuclear power plant reactor vessels is the prediction of the level of crack resistance of reactor steels. The paper shows the possibility of estimating the neutron irradiation level on the nature of the temperature dependence of KIC. The prediction of the influence of radiation damage on the fracture toughness of the reactor steel can be obtained on the basis of the results of tests of small cylindrical samples with annular notches.

Nuclear Power Plant Fires and Explosions: Part IV — Water Hammer Explosion Mechanisms

2017 ◽  
Author(s):  
Robert A. Leishear
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Water Hammer ◽  
Compression Process ◽  
Flammable Gas ◽  
Piping Systems ◽  
Fukushima Daiichi ◽  
Accident Conditions

Water hammers, or fluid transients, compress flammable gasses to their autognition temperatures in piping systems to cause fires or explosions. While this statement may be true for many industrial systems, the focus of this research are reactor coolant water systems (RCW) in nuclear power plants, which generate flammable gasses during normal operations and during accident conditions, such as loss of coolant accidents (LOCA’s) or reactor meltdowns. When combustion occurs, the gas will either burn (deflagrate) or explode, depending on the system geometry and the quantity of the flammable gas and oxygen. If there is sufficient oxygen inside the pipe during the compression process, an explosion can ignite immediately. If there is insufficient oxygen to initiate combustion inside the pipe, the flammable gas can only ignite if released to air, an oxygen rich environment. This presentation considers the fundamentals of gas compression and causes of ignition in nuclear reactor systems. In addition to these ignition mechanisms, specific applications are briefly considered. Those applications include a hydrogen fire following the Three Mile Island meltdown, hydrogen explosions following Fukushima Daiichi explosions, and on-going fires and explosions in U.S nuclear power plants. Novel conclusions are presented here as follows. 1. A hydrogen fire was ignited by water hammer at Three Mile Island. 2. Hydrogen explosions were ignited by water hammer at Fukushima Daiichi. 3. Piping damages in U.S. commercial nuclear reactor systems have occurred since reactors were first built. These damages were not caused by water hammer alone, but were caused by water hammer compression of flammable hydrogen and resultant deflagration or detonation inside of the piping.

The analysis of emergency situations related to fires at nuclear power plants

2021 ◽  
Vol 30 (5) ◽  
pp. 66-75
Author(s):  
S. A. Titov ◽  
N. M. Barbin ◽  
A. M. Kobelev
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Reactor Core ◽  
Emergency Situations ◽  
The Usa ◽  
Large Fires ◽  
Short Circuits ◽  
Nuclear Reactor Core

Introduction. The article provides a system and statistical analysis of emergency situations associated with fires at nuclear power plants (NPPs) in various countries of the world for the period from 1955 to 2019. The countries, where fires occurred at nuclear power plants, were identified (the USA, Great Britain, Switzerland, the USSR, Germany, Spain, Japan, Russia, India and France). Facilities, exposed to fires, are identified; causes of fires are indicated. The types of reactors where accidents and incidents, accompanied by large fires, have been determined.The analysis of major emergency situations at nuclear power plants accompanied by large fires. During the period from 1955 to 2019, 27 large fires were registered at nuclear power plants in 10 countries. The largest number of major fires was registered in 1984 (three fires), all of them occurred in the USSR. Most frequently, emergency situations occurred at transformers and cable channels — 40 %, nuclear reactor core — 15 %, reactor turbine — 11 %, reactor vessel — 7 %, steam pipeline systems, cooling towers — 7 %. The main causes of fires were technical malfunctions — 33 %, fires caused by the personnel — 30 %, fires due to short circuits — 18 %, due to natural disasters (natural conditions) — 15 % and unknown reasons — 4 %. A greater number of fires were registered at RBMK — 6, VVER — 5, BWR — 3, and PWR — 3 reactors.Conclusions. Having analyzed accidents, involving large fires at nuclear power plants during the period from 1955 to 2019, we come to the conclusion that the largest number of large fires was registered in the USSR. Nonetheless, to ensure safety at all stages of the life cycle of a nuclear power plant, it is necessary to apply such measures that would prevent the occurrence of severe fires and ensure the protection of personnel and the general public from the effects of a radiation accident.

scholarly journals Structural Modeling and Dynamic Analysis of a Nuclear Reactor Building

2020 ◽  
Author(s):  
Evrim Oyguc ◽  
Abdul Hayır ◽  
Resat Oyguc
Keyword(s):  
Nonlinear Dynamic ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Energy Sources ◽  
Finite Element Program ◽  
Design Spectrum ◽  
Reactor Building ◽  
Set Up

Increasing energy demand urge the developing countries to consider different types of energy sources. Owing the fact that the energy production capacity of renewable energy sources is lower than a nuclear power plant, developed countries like US, France, Japan, Russia and China lead to construct nuclear power plants. These countries compensate 80% of their energy need from nuclear power plants. Further, they periodically conduct tests in order to assess the safety of the existing nuclear power plants by applying impact type loads to the structures. In this study, a sample third-generation nuclear reactor building has been selected to assess its seismic behavior and to observe the crack propagations of the prestressed outer containment. First, a 3D model has been set up using ABAQUS finite element program. Afterwards, modal analysis is conducted to determine the mode shapes. Nonlinear dynamic time history analyses are then followed using an artificial strong ground motion which is compatible with the mean design spectrum of the previously selected ground motions that are scaled to Eurocode 8 Soil type B design spectrum. Results of the conducted nonlinear dynamic analyses are considered in terms of stress distributions and crack propagations.

Steady-State Thermal-Hydraulic Analysis of a Particle-Bedded Boiling Water Reactor

2009 ◽  
Author(s):  
Xiaoyu Cai ◽  
Suizheng Qiu ◽  
Guanghui Su ◽  
Changyou Zhao
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Superheated Steam ◽  
Nuclear Reactor ◽  
Hydraulic Analysis ◽  
Light Water ◽  
Safety Systems ◽  
Fuel Elements ◽  
Thermal Hydraulic Analysis

The current Light Water Reactors both BWR and PWR have extensive nuclear reactor safety systems, which provide safe and economical operation of Nuclear Power Plants. During about forty years of operation history the safety systems of Nuclear Power Plants have been upgraded in an evolutionary manner. The cost of safety systems, including large containments, is really high due to a capital cost and a long construction period. These conditions together with a low efficiency of steam cycle for LWR create problems to build new power plants in the USA and in the Europe. An advanced Boiling Water Reactor concept with micro-fuel elements (MFE) and superheated steam promises a radical enhancement of safety and improvement of economy of Nuclear Power Plants. In this paper, a new type of nuclear reactor is presented that consists of a steel-walled tube filled with millions of TRISO-coated fuel particles (Micro-Fuel Elements, MFE) directly cooled by a light-water coolant-moderator. Water is used as coolant that flows from bottom to top through the tube, thereby fluidizing the particle bed, and the moderator water flows in the reverse direction out of the tube. The fuel consists of spheres of about 2.5 mm diameter of UO2 with several coatings of different carbonaceous materials. The external coating of steam cycle the particles is silicon carbide (SiC), manufactured with chemical vapor deposit (CVD) technology. Steady-State Thermal-Hydraulic Analysis aims at providing heat transport capability which can match with the heat generated by the core, so as to provide a set of thermal hydraulic parameters of the primary loop. So the temperature distribution and the pressure losses along the direction of flow are calculated for equilibrium core in this paper. The calculation not only includes the liquid region, but the two phase region and the superheated steam region. The temperature distribution includes both the temperature parameters of micro-fuel elements and the coolant. The results show that the maximum fuel temperature is much lower than the limitation and the flow distribution can meet the cooling requirement in the reactor core.

Guided Waves as an Online Monitoring Technology for Long-Term Operation in Nuclear Power Plants: Experimental Results on a Steam Discharge Pipe

2019 ◽  
Vol 5 (1) ◽  
Author(s):  
Mauro Cappelli ◽  
Francesco Cordella ◽  
Francesco Bertoncini ◽  
Marco Raugi
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Guided Waves ◽  
Complex Structure ◽  
Theoretical Background ◽  
Guided Wave ◽  
Experimental Results ◽  
Term Operation

Guided wave (GW) testing is regularly used for finding defect locations through long-range screening using low-frequency waves (from 5 to 250 kHz). By using magnetostrictive sensors, some issues, which usually limit the application to nuclear power plants (NPPs), can be fixed. The authors have already shown the basic theoretical background and simulation results concerning a real steel pipe, used for steam discharge, with a complex structure. On the basis of such theoretical framework, a new campaign has been designed and developed on the same pipe, and the obtained experimental results are now here presented as a useful benchmark for the application of GWs as nondestructive techniques. Experimental measures using a symmetrical probe and a local probe in different configurations (pulse-echo and pitch-catch) indicate that GW testing with magnetostrictive sensors can be reliably applied to long-term monitoring of NPPs components.

Life Beyond 60 Years: The Importance of Sustaining the Current Fleet of Light Water Reactors in the U.S. and the R&D Needs

2010 ◽  
Author(s):  
Ronaldo Szilard ◽  
Hongbin Zhang
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Superior Performance ◽  
Light Water Reactors ◽  
Economic Operation ◽  
Significant Interest ◽  
Water Reactors ◽  
The U.S

The current fleet of 104 nuclear power plants in the U.S. began their operation with 40 years operating licenses. About half of these plants have their licenses renewed to 60 years and most of the remaining plants are anticipated to pursue license extension to 60 years. With the superior performance of the current fleet and formidable costs of building new nuclear power plants, there has been significant interest to extend the lifetime of the current fleet even further from 60 years to 80 years. This paper addresses some of the key long term technical challenges and identifies R&D needs related to the long term safe and economic operation of the current fleet.

Research Activities in the European Union on Ageing Management for Long Term Operation of Nuclear Power Plants

2010 ◽  
Author(s):  
Oliver Martin ◽  
Antonio Ballesteros ◽  
Christiane Bruynooghe ◽  
Michel Bie`th
Keyword(s):  
Energy Supply ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Age Distribution ◽  
Term Operation ◽  
Research Activities ◽  
Ageing Management ◽  
The Eu

The energy supply of the future in the EU will be a mix of renewable, fossil and nuclear. There are 145 nuclear power reactors in operation in 15 out of the 27 EU countries, with installed power ∼132 GWe. The age distribution of current nuclear power plants in EU is such that in 2010 most of them will have passed 20-years and approximately 25% of them 30 years of age. The decrease of energy supply from nuclear generated electricity can not always be compensated in a reliable and economical way within a short time span. For this situation utilities may be keen to upgrade the reactor output and /or to ask their regulatory bodies for longer term operation. Under the research financed in the Euratom part of the Research Directorate (RTD) of the European Commission several projects explicitly address the safe long term operation of nuclear power plants (NULIFE, LONGLIFE) and the topics proposed in the 2010 call explicitly address issues concerning component ageing, in particular non metallic components, i.e. instrumentation and cables (I&C) and concrete ageing. This paper presents an overview of the plans for long term operation (LTO) of nuclear power plants in the EU. Special emphasis is given on research activities on component ageing management and long term operation issues related to safety.

Sign in / Sign up

Export Citation Format

Share Document