Effects of CeO2 on Microstructure and Corrosion Performance of the Coatings Prepared by Pulse Micro Arc Oxidation on AZ31B Mg Alloy

2020 ◽  
Vol 20 (8) ◽  
pp. 4778-4786
Author(s):  
Lilu Qin ◽  
Jiamu Huang ◽  
Longlong Hao ◽  
Jun Su ◽  
Niu Ma ◽  
...  
Keyword(s):  
Magnesium Alloy ◽  
Current Density ◽  
Corrosion Current Density ◽  
Corrosion Potential ◽  
Salt Spray ◽  
Electrochemical Measurement ◽  
Corrosion Current ◽  
Corrosion Performance ◽  
Micro Arc Oxidation ◽  
Micro Morphology

To improve corrosion performance of coatings on AZ31B magnesium alloy, the nano-CeO2 additives were included in Na2SiO3 based electrolyte during process of pulse micro arc oxidation (MAO). The MAO-CeO2 coating was successfully prepared to characterize its structure, micro morphology and composition. The XRD results indicated that MAO-CeO2 coatings were consisted of Mg2SiO4, MgSiO3, MgF2 and CeO2. The intensity of CeO2 peaks increases with increasing nano-CeO2 particles in electrolyte. The number of cracks on MAO-CeO2 coatings exhibited a V-shaped trend with increase in nano-CeO2 content. Meanwhile, the influence of nano-CeO2 on corrosion behavior of MAO-CeO2 coatings is investigated by salt spray test and electrochemical measurement. The corrosion current density of coatings presented same trend and corrosion potential is further studied. The MAO-CeO2 coatings formed in electrolyte with 10 g/L nano-CeO2 showed best corrosion performance which has the lowest corrosion current density of 0.58 nA/cm2 and the highest corrosion potential of - 1269 mVSCE.

Electrochemical Characteristics of Al-Based Coating on Magnesium Alloy Fabricated by Supersonic Particles Deposition

2013 ◽  
Vol 756-759 ◽  
pp. 85-88
Author(s):  
Xiao Ming Wang ◽  
Sheng Zhu ◽  
Qing Chang ◽  
Guo Feng Han
Keyword(s):  
Electrochemical Impedance Spectroscopy ◽  
Magnesium Alloy ◽  
Impedance Spectroscopy ◽  
Current Density ◽  
Corrosion Current Density ◽  
Corrosion Potential ◽  
Electrochemical Impedance ◽  
Corrosion Current ◽  
Electrochemical Characteristics ◽  
Order Of Magnitude

Al-based coating on ZM5 magnesium alloy was prepared by Supersonic Particles Deposition (SPD). Electrochemical working station was utilized to test polarization curve, corrosion potential and electrochemical impedance spectroscopy etc. The results indicted that corrosion potential of Al-Si coating was about-767.6mV, much higher than that of ZM5 Mg-substrate; And corrosion current density of the coating sample decreased three order of magnitude than that of the uncoated. Compared to Mg-substrate, the radius of capacitive impedance arc of the coating enlarged and impedance modulus improved two order of magnitude.

A Study on the Electroless Ni–P Deposition of AM60B Magnesium Alloy without HF in Bath

2014 ◽  
Vol 633-634 ◽  
pp. 879-882 ◽  
Author(s):  
Jing Dong Qiu ◽  
Su Qiu Jia
Keyword(s):  
Corrosion Resistance ◽  
Magnesium Alloy ◽  
Current Density ◽  
Corrosion Current Density ◽  
Corrosion Potential ◽  
Electroless Nickel ◽  
Corrosion Current ◽  
Dense Structure ◽  
Electroless Ni

Based on the traditional direct electroless nickel methods, chemical baths are improved by removing HF. Examinations have been carried out on the Ni-P deposited on the interlayer for morphology, composition and corrosion-resistance by SEM, EDS, XRD and other instruments. A Ni-P film with fine and dense structure was obtained on the AM60B magnesium alloy. It exhibits lower corrosion current density and more positive corrosion potential than the substrate.

scholarly journals An electrochemical method to investigate the effects of compound composition on gold dissolution in thiosulfate solution

2020 ◽  
Vol 9 (1) ◽  
pp. 496-502 ◽  
Author(s):  
Zhaohui Zhang ◽  
Bailong Liu ◽  
Mei Wu ◽  
Longxin Sun
Keyword(s):  
Dissolution Rate ◽  
Current Density ◽  
Polarization Resistance ◽  
Electrochemical Method ◽  
Corrosion Current Density ◽  
Corrosion Potential ◽  
Corrosion Current ◽  
Gold Dissolution ◽  
Tafel Polarization ◽  
Edta Solution

AbstractThe electrochemical behavior of gold dissolution in the Cu2+–NH3–S2O32−–EDTA solution has been investigated in detail by deriving and analyzing the Tafel polarization curve, as this method is currently widely implemented for the electrode corrosion analysis. The dissolution rate of gold in Cu2+–NH3–S2O32−–EDTA solution was determined based on the Tafel polarization curves, and the effects of various compound compositions in a Cu2+–NH3–S2O32−–EDTA mixture on the corrosion potential and corrosion current density were analyzed. The results showed that the corrosion potential and polarization resistance decreased, whereas the corrosion current density increased for certain concentrations of S2O32−–NH3–Cu2+ and EDTA, indicating that the dissolution rate of gold had changed. The reason for promoting the dissolution of gold is also discussed.

Electrochemical Characteristics of Lanthanum Hexaboride in the Environments Containing S2-

2010 ◽  
Vol 663-665 ◽  
pp. 473-476
Author(s):  
Shu Qi Zheng ◽  
Chang Feng Chen ◽  
Rui Jing Jiang ◽  
Dan Ni Wang
Keyword(s):  
Partial Pressure ◽  
Corrosion Behavior ◽  
Current Density ◽  
Corrosion Current Density ◽  
Corrosion Potential ◽  
Corrosion Current ◽  
Lanthanum Hexaboride ◽  
Electrochemical Characteristics

In the environment with H2S/CO2 or Na2S, the corrosion behavior of Lanthanum hexaboride (LaB6) was investigated by electrochemistry methods. The results indicated that the corrosion potential (Ecorr) and Rf of LaB6 increased as the partial pressure of H2S increased, while the corrosion current density (Icorr) decreased. In the environment containing Na2S, as the content of Na2S increased, the corrosion potential (Ecorr) and Rf of LaB6 decreased, while the corrosion current density (Icorr) increased. Thus, the addition of H2S into the environment with H2S/CO2 would inhibit the corrosion of LaB6; while in the environment containing Na2S, the increasing of the content of Na2S would accelerate the corrosion of LaB6.

Study on the Effects of Realkalization Rehabilitation Method Auxiliary Alcamines Inhibitors in Simulative Experiment

2011 ◽  
Vol 243-249 ◽  
pp. 5562-5566
Author(s):  
Jin Liang Lu ◽  
Jun Xi Zhang ◽  
Jun Jiang ◽  
Kun Wang ◽  
Wen Jun Qu
Keyword(s):  
Relaxation Time ◽  
Impedance Spectroscopy ◽  
Current Density ◽  
Corrosion Current Density ◽  
Sodium Carbonate Solution ◽  
Corrosion Potential ◽  
Corrosion Current ◽  
Mixed Solution ◽  
Repair Technique ◽  
Electrochemical Parameters

In this paper, the feasibility of inhibitor auxiliary re-alkalization was investigated. The effect of realkalization auxiliary inhibitor repair technique was studied by simulative experiment. It studied the changes of electrochemical parameters of the natural carbonated reinforced concrete during the electrochemical realkalization in 1mol/L Na2CO3 solution and the mixed solution of 1mol/L Na2CO3 and 1 mol/L DMEA , as well as the impedance spectroscopy and polarization curves in the process of relaxation. The results showed that: there appears to be no effect of DMEA on the corrosion potential and the impedance of the steel in the process of realkalization. That was, the performance was the same as that in the sodium carbonate solution except corrosion current of rebar with DMEA which showed much lower. But of the samples which the DMEA existed in the electrolyte was significantly shorter at the same relaxation time after realkalization. At the same relaxation time the corrosion potential was more positive and the corrosion current density was smaller. It improved significantly the effect of realkalization.

scholarly journals Influence of Seawater Salinity on Corrosion of Austenitic Steel

2019 ◽  
Vol 26 (3) ◽  
pp. 219-225
Author(s):  
Robert Starosta
Keyword(s):  
Sodium Chloride ◽  
Corrosion Rate ◽  
Austenitic Steel ◽  
Current Density ◽  
Corrosion Current Density ◽  
Corrosion Potential ◽  
Saturated Calomel Electrode ◽  
Corrosion Current ◽  
Seawater Salinity ◽  
Corrosion Susceptibility

Abstract Due to the paramagnetic properties and the ability to passivation, for the production of hulls of some vessels (mainly warships), corrosion-resistant (stainless) steels with austenitic structure are used. This article describes the influence of seawater salinity on selected corrosion properties of high-alloy steel X5CrNi 18-10 (304). The average salinity of the seas is taken as 3.5% content of sodium chloride. Corrosion rate of the tested material was evaluated in an aqueous solution of sodium chloride was evaluated. The NaCl concentration in corrosive solutions was 0.7%, 1.4%, 2.1%, 2.8%, 3.5%, 4.2%. Corrosion tests were performed using the potentiodynamic method. The range of electrochemical potential changes was Ecorr ±150 mV. Corrosion rate was assessed on the basis of corrosion current density measurements. Corrosion potential values against the saturated calomel electrode were also determined. Based on the obtained measurement results and non-parametric significance tests carried out, a significant influence of seawater salinity on the value of corrosion current density and corrosion potential was found. The highest value of corrosion current density (jcorr), and thus the highest corrosion rate, was recorded for 3.5% NaCl solution. In the concentration range from 0.7 to 3.5% NaCl in solution, the corrosion rate of austenitic steel increases. A further increase in salinity of electrolyte results in the inhibition of corrosion rate of steel. There is almost a full negative, linear correlation between the proportion of sodium chloride in the corrosive solution and the value of corrosion potential. Along with the rise in the salinity of seawater, increase the electrochemical activity, and thus the corrosion susceptibility, thus the corrosion susceptibility, of the austenitic steel X5CrNi 18-10 was observed.

Corrosion Resistance of Mg-4Zn Alloy with Amorphous Micro-Arc Oxidation Coating in Simulated Body Fluid

2016 ◽  
Vol 852 ◽  
pp. 1325-1333
Author(s):  
Li Chen Zhao ◽  
Shuang Jin Liu ◽  
Yu Min Qi ◽  
Chun Xiang Cui
Keyword(s):  
Corrosion Resistance ◽  
Simulated Body Fluid ◽  
Current Density ◽  
Polarization Resistance ◽  
Body Fluid ◽  
Corrosion Current Density ◽  
Corrosion Current ◽  
Metal Substrate ◽  
Electrochemical Measurements ◽  
Micro Arc Oxidation

A binary Mg-4Zn alloy was fabricated as a potential degradable biomaterial. To improve the corrosion resistance of Mg-4Zn alloy, an amorphous micro-arc oxidation (MAO) coating was prepared on the Mg-4Zn substrate. Electrochemical measurements and immersion tests were employed to evaluate the corrosion resistance of the specimen in simulated body fluid (SBF). Electrochemical measurements show that the Mg-4Zn alloy covered with a MAO coating has a much lower corrosion current density and a much greater polarization resistance. Immersion tests suggest that the degradation of Mg-4Zn substrate is relatively serious during the initial 8 h of immersion although it has been protected by a MAO coating. When most micro-pores within the MAO coating have been filled with precipitates resulted from the corrosion of the metal substrate, the degradation of the Mg-4Zn substrate is significantly delayed.

Corrosion behavior of X80 steel under disbond coating interfered with AC

2019 ◽  
Vol 66 (6) ◽  
pp. 704-718
Author(s):  
Qingmiao Ding ◽  
Zili Li ◽  
Tao Shen ◽  
Gan Cui
Keyword(s):  
Corrosion Behavior ◽  
Current Density ◽  
Corrosion Current Density ◽  
Corrosion Potential ◽  
Corrosion Current ◽  
The Self ◽  
Stray Current ◽  
Content Type ◽  
X80 Steel ◽  
Protection Potential

Purpose This paper aims to research the corrosion behavior of the metal under the disbonded coatings interfered with AC through electrochemical method. Design/methodology/approach The corrosion behavior of the metal under disbond coating interfered with alternate stray current (AC) was studied by electrochemical methods using the rectangular coating disbonded simulator. The obtained data from electrode potential test, electrochemical impedance spectroscopy (EIS) and polarization curves in simulated soil solution indicated that under the natural corrosion condition, the self-corrosion potential and the corrosion current density of the metal at different depths under disbond coating had obviously changed if there was AC interference. Findings The self-corrosion potential of the metal at the same depths under disbond coating shifted negatively with the rising of the AC voltage. Under the condition of cathode polarization, there was still obvious potential gradient with the extension of the deep peeling of the coating gap, and the corrosion current density of the test points was minimum, and the protection effect was best when the cathode protection potential was −1.0 V. When the metal was applied with over-protection, the corrosion rate of the metal increased as AC stray current flowing through it increased. Originality/value This paper used the rectangular aperture device to study the corrosion behavior of X80 steel under the disbonded coatings through electrochemical methods when the AC stray current interference voltage was 0V, 1V, 5V or 10V and the protection potential was 0V, −0.9V, −1.0V, −1.2V or −1.3V, respectively. There is great significance to the safe operation and long-term service of pipeline steel in soil environment.

scholarly journals Experimental Study on the Influence of Sulfate Reducing Bacteria on the Metallic Corrosion Behavior under Disbonded Coating

2017 ◽  
Vol 2017 ◽  
pp. 1-13 ◽  
Author(s):  
Qingmiao Ding ◽  
Liping Fang ◽  
Yanyu Cui ◽  
Yujun Wang
Keyword(s):  
Corrosion Behavior ◽  
Current Density ◽  
Corrosion Current Density ◽  
Corrosion Potential ◽  
Corrosion Current ◽  
Test Point ◽  
Sulfate Reducing ◽  
Metallic Corrosion ◽  
Reducing Bacteria ◽  
Disbonded Coating

A rectangle disbonded coating simulation device was used to research the effect of sulfate reducing bacteria (SRB) on the metallic corrosion behavior under disbonded coating by the electrochemical method. The results showed that the metal self-corrosion potential at the same test point had little change in the initial experiment stage, whether the solution was without or with SRB. The potential amplitude in the solution with SRB was larger than that without SRB in the later corrosion period. The corrosion current density of the metal at the same test point increased gradually over time in the solution with or without SRB, and SRB could accelerate the corrosion of the metal in the disbonded crevice. The metal self-corrosion potential in the crevice had little change in the SRB solution environment after adding the fungicide, but the corrosion current density decreased significantly. That meant the growth and reproduction of SRB were inhibited after adding the fungicide, so the metal corrosion rate slowed down. Among the three kinds of solution environment, increasing the coating disbonded thickness could accelerate the corrosion of the metal in the crevice, and it was the largest in the solution with SRB.

Corrosion Behavior of Tungsten Copper Alloy Produced by Infiltration Sintering

2015 ◽  
Vol 816 ◽  
pp. 699-704
Author(s):  
Bo Lv ◽  
Da Tong Zhang
Keyword(s):  
Corrosion Behavior ◽  
Corrosion Potential ◽  
Salt Spray ◽  
Electrochemical Measurement ◽  
Corrosion Current ◽  
Immersion Test ◽  
Cold Isostatic Pressing ◽  
Neutral Salt ◽  
Bonding Phase ◽  
Superior Corrosion Resistance

In this paper, W80CuNi0.3 alloy was prepared by cold isostatic pressing (CIP) and infiltration sintering, and its corrosion behavior was investigated by neutral salt spray accelerated test, immersion test and electrochemical measurement. It turned out that in the neutral salt spray and immersion test,the mass loss and corrosion rate of W80CuNi0.3 were far lower than those of 45 steel. The corrosion mainly occurs in the bonding phase of Cu, and the initial corrosion form of W80CuNi0.3 was pitting, the main reason of W80CuNi0.3 corrosion was Cl- erosion. The polarization curves analysis showed that compared with 45 steel, W80CuNi0.3 alloy had higher corrosion potential and lower corrosion current. Therefore, W80CuNi0.3 alloy are prone to stable passivation, so it has superior corrosion resistance.

Sign in / Sign up

Export Citation Format

Share Document