Effect of Chopped Basalt Fiber on the Fresh and Hardened Properties of Fly Ash High Strength Concrete

2014 ◽  
Vol 567 ◽  
pp. 381-386 ◽  
Author(s):  
Nasir Shafiq ◽  
Muhd Fadhil Nuruddin ◽  
Ali Elheber Ahmed Elshekh ◽  
Ahmed Fathi Mohamed Salih
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Basalt Fiber ◽  
High Strength ◽  
Progressive Increase ◽  
Test Results ◽  
Strength Concrete ◽  
Hardened Properties ◽  
Chopped Basalt Fiber

In order to improve the mechanical properties of high strength concrete, HSC, several studies have been conducted using fly ash, FA. Researchers have made it possible to achieve 100-150MPa high strength concrete. Despite the popularity of this FAHSC, there is a major shortcoming in that it becomes more brittle, resulting in less than 0.1% tensile strain. The main objective of this work was to evaluate the fresh and hardened properties of FAHSC utilizing chopped basalt fiber stands, CBFS, as an internal strengthening addition material. This was achieved through a series of experimental works using a 20% replacement of cement by FA together with various contents of CBFS. Test results of concrete mixes in the fresh state showed no segregation, homogeneousness during the mixing period and workability ranging from 60 to 110 mm. Early and long terms of compressive strength did not show any improvement by using CBFS; in fact, it decreased. This was partially substituted by the effect of FA. Whereas, the split and flexural strengths of FASHC were significantly improved with increasing the content of CBFS as well as the percentage of the split and flexural tensile strength to the compressive strength. Also, test results showed a progressive increase in the areas under the stress-strain curves of the FAHSC strains after the CBFS addition. Therefore, the brittleness and toughness of the FAHSC were enhanced and the pattern of failure moved from brittle failure to ductile collapse using CBFS. It can be considered that the CBFS is a suitable strengthening material to produce ductile FAHSC.

Effects of Nano-CaCO3 on the Compressive Strength and Microstructure of High Strength Concrete in Different Curing Temperature

2011 ◽  
Vol 121-126 ◽  
pp. 126-131 ◽  
Author(s):  
Qing Lei Xu ◽  
Tao Meng ◽  
Miao Zhou Huang
Keyword(s):  
Compressive Strength ◽  
Low Temperature ◽  
High Strength Concrete ◽  
High Strength ◽  
Curing Temperature ◽  
Test Results ◽  
Strength Concrete ◽  
Calcium Nitrite ◽  
Orientation Index ◽  
Early Strength

In this paper, effects of nano-CaCO3 on compressive strength and Microstructure of high strength concrete in standard curing temperature(21±1°C) and low curing temperature(6.5±1°C) was studied. In order to improve the early strength of the concrete in low temperature, the early strength agent calcium nitrite was added into. Test results indicated that 0.5% dosage of nano-CaCO3 could inhibit the effect of calcium nitrite as early strength agent, but 1% and 2% dosage of nano-CaCO3 could improve the strength of the concrete by 13% and 18% in standard curing temperature and by 17% and 14% in low curing temperature at the age of 3days. According to the XRD spectrum, with the dosage up to 1% to 2%, nano-CaCO3 can change the orientation index significantly, leading to the improvement of strength of concrete both in standard curing temperature and low curing temperature.

scholarly journals A Study on the Thermal Properties of High-Strength Concrete Containing CBA Fine Aggregates

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1493 ◽  
Author(s):  
In-Hwan Yang ◽  
Jihun Park
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Ultrasonic Velocity ◽  
High Strength Concrete ◽  
High Strength ◽  
Unit Weight ◽  
Test Results ◽  
Strength Concrete ◽  
Fine Aggregates

The thermal conductivity of concrete is a key factor for efficient energy consumption in concrete buildings because thermal conductivity plays a significant role in heat transfer through concrete walls. This study investigated the effects of replacing fine aggregates with coal bottom ash (CBA) and the influence of curing age on the thermal properties of high-strength concrete with a compressive strength exceeding 60 MPa. The different CBA aggregate contents included 25%, 50%, 75%, and 100%, and different curing ages included 28 and 56 days. For concrete containing CBA fine aggregate, the thermal and mechanical properties, including the unit weight, thermal conductivity, compressive strength, and ultrasonic velocity, were measured. The experimental results reveal that the unit weight and thermal conductivity of the CBA concrete were highly dependent on the CBA content. The unit weight, thermal conductivity, and compressive strength of the concrete decreased as the CBA content increased. Relationships between the thermal conductivity and the unit weight, thermal conductivity and compressive strength of the CBA concrete were proposed in the form of exponential functions. The equations proposed in this study provided predictions that were in good agreement with the test results. In addition, the test results show that there was an approximately linear relationship between the thermal conductivity and ultrasonic velocity of the CBA concrete.

scholarly journals Multigene Genetic Programming for Estimation of Elastic Modulus of Concrete

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Alireza Mohammadi Bayazidi ◽  
Gai-Ge Wang ◽  
Hamed Bolandi ◽  
Amir H. Alavi ◽  
Amir H. Gandomi
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Genetic Programming ◽  
High Strength Concrete ◽  
Elastic Moduli ◽  
High Strength ◽  
Test Results ◽  
Strength Concrete ◽  
Multigene Genetic Programming ◽  
Compressive Strength Test

This paper presents a new multigene genetic programming (MGGP) approach for estimation of elastic modulus of concrete. The MGGP technique models the elastic modulus behavior by integrating the capabilities of standard genetic programming and classical regression. The main aim is to derive precise relationships between the tangent elastic moduli of normal and high strength concrete and the corresponding compressive strength values. Another important contribution of this study is to develop a generalized prediction model for the elastic moduli of both normal and high strength concrete. Numerous concrete compressive strength test results are obtained from the literature to develop the models. A comprehensive comparative study is conducted to verify the performance of the models. The proposed models perform superior to the existing traditional models, as well as those derived using other powerful soft computing tools.

Test Research on Strength of Concrete Shaft Lining under Salt Disaster Corrosion

2014 ◽  
Vol 926-930 ◽  
pp. 645-648 ◽  
Author(s):  
Xu Rong Li ◽  
Hong Guang Ji ◽  
Jun Wang ◽  
Cheng Lin Song
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Solution Concentration ◽  
Test Results ◽  
Strength Concrete ◽  
Strength Change ◽  
Lining Structure ◽  
Shaft Lining

In order to study the strength change of high strength concrete shaft lining structure in underground complex environment resisting composite salt damage erosion, C70 high strength concrete test specimens were made and composite salt disaster solutions of different concentrations were compounded. The test results show that the coefficient of compressive strength and flexural strength of high strength concrete increase in early corrosion and then decline. The strength of specimen declines more quickly in higher corrosion solution concentration in latter time. The change law of the flexural strength is more complex than the compressive strength. Composite salt disaster solutions have little effect for no damage high strength concrete.

scholarly journals Effect of Steel Fiber Aspect Ratio on the Properties of High Strength Self Compacting Concrete

2019 ◽  
Vol 9 (2) ◽  
pp. 2938-2941
Keyword(s):  
Compressive Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Steel Fibers ◽  
Self Compacting Concrete ◽  
Split Tensile Strength ◽  
Strength Concrete ◽  
Fiber Aspect Ratio ◽  
Aspect Ratios ◽  
Hardened Properties

The High strength concrete defined as per IS 456 as the concrete having characteristic compressive strength more than 65 MPa. The self-compacting concrete has lot of advantages including concreting at congested reinforcement locations, better finish, good compaction etc. The inclusion of fibers in the concrete mix decreases the brittle nature of concrete thereby the ductility increases. Different types of fibers are available for inclusion in concrete like steel, glass, polypropylene, basalt, etc. In the present investigation, high strength concrete having characteristic strength of 90 MPa was developed and hooked ended steel fibers are used and the hardened properties are determined. Steel fibers having diameter of 1 mm and lengths of 25 and 50 mm were added to concrete in 0.125%, 0.25% and 0.5% by volume of concrete. Three hardened properties compressive strength, split tensile Strength and flexural strength were determined. Out of the two lengths of fiber i.e with two aspect ratios, the fiber with 50 mm length yielded better results.

scholarly journals Strength Determination of High Strength Concrete Blended with Copper Slag and Fly Ash

2021 ◽  
Vol 9 (VII) ◽  
pp. 1198-1203
Author(s):  
Jamshed Alam
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Free Water ◽  
High Strength ◽  
Copper Slag ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Strength Concrete ◽  
Free Water Content

An experimental analysis was conducted to study the effects of using copper slag as a fine aggregate (FA) and the effect of fly ash as partial replacement of cement on the properties high strength concrete. In this analysis total ten concrete mixtures were prepared, out of which five mixes containing different proportions of copper slag ranging from 0% (for the control mix) to 75% were prepared and remaining five mixes containing fly ash as partial replacement of cement ranging from 6% to 30% (all mixes contains 50% copper slag as sand replacements). Concrete matrix were tested for compressive strength, tensile strength and flexural strength tests. Addition of copper slag as sand replacement up to 50% yielded comparable strength with that of the control matrix. However, further additions of copper slag, caused reduction in strength due to an increment of the free water content in the mix. Concrete mix with 75% copper slag replacement gave the lowest compressive strength value of approximately 80 MPa at 28 days curing period, which is almost 4% more than the strength of the control mix. For this concrete containing 50% copper slag, fly ash is introduced in the concrete to achieve the better compressive, split and flexural strengths. It was also observed that, introduction of the fly ash gave better results than concrete containing 50% copper slag. When concrete prepared with 18 % of fly ash, the strength has increased approximately 4%, and strength decreased with further replacements of the cement with fly ash. Hence, it is suggested that 50% of copper slag can be used as replacement of sand and 18% fly ash can be used as replacement of cement in order to obtain high strength concrete.

scholarly journals The Use of Fly Ash as Additive Material to High Strength Concrete

2018 ◽  
Vol 20 (2) ◽  
pp. 65-70
Author(s):  
Endah Kanti Pangestuti ◽  
Sri Handayani ◽  
Mego Purnomo ◽  
Desi Christine Silitonga ◽  
M. Hilmy Fathoni
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Building Materials ◽  
High Strength ◽  
Coal Waste ◽  
Normal Concrete ◽  
Strength Concrete ◽  
Concrete Mixtures ◽  
Compressive Strength Of Concrete

Abstract. The use of coal waste (Fly Ash) is currently being developed in building materials technology, as a high-strength concrete mix material. This study aims to determine the strength of concrete by adding fly ash as a substitute for cement in high-strength concrete mixtures. This research was conducted with an experimental method to obtain results and data that would confirm the variables studied. The total number of specimens used in this study were 36 pieces with different sizes of cube tests which were 15 cm x 15 cm x 15 cm. A total of 36 concrete samples were used to test the compressive strength of concrete with a percentage of Fly Ash in  0% (normal concrete), 20%, 25% and 30% with a concrete treatment age of 7 days, 21 days and 28 days. A total of 12 more samples were used to test water absorption in concrete at 28 days of maintenance. Each percentage percentage of Fly Ash uses 3 concrete test samples. The increase in compressive strength occurs at 7, 21 and 28 days in concrete. However, the compressive strength of concrete produced by concrete using the percentage of Fly Ash is always lower than the value of normal concrete compressive strength. From testing the compressive strength of concrete at 28 days of treatment with content of 0%, 20%, 25% and 30% Fly Ash obtained results of 45.87 MPa, 42.67 MPa, 40.89 MPa, and 35.27 MPa respectively

Sign in / Sign up

Export Citation Format

Share Document