scholarly journals A zonal approach for estimating pressure ratio at compressor extreme off-design conditions

2018 ◽  
Vol 20 (4) ◽  
pp. 393-404 ◽  
Author(s):  
José Galindo ◽  
Roberto Navarro ◽  
Luis Miguel García-Cuevas ◽  
Daniel Tarí ◽  
Hadi Tartoussi ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Speed ◽  
Internal Combustion Engines ◽  
Pressure Ratio ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Combustion Engines ◽  
One Dimensional ◽  
Performance Map

Zero-dimensional/one-dimensional computational fluid dynamics codes are used to simulate the performance of complete internal combustion engines. In such codes, the operation of a turbocharger compressor is usually addressed employing its performance map. However, simulation of engine transients may drive the compressor to work at operating conditions outside the region provided by the manufacturer map. Therefore, a method is required to extrapolate the performance map to extended off-design conditions. This work examines several extrapolating methods at the different off-design regions, namely, low-pressure ratio zone, low-speed zone and high-speed zone. The accuracy of the methods is assessed with the aid of compressor extreme off-design measurements. In this way, the best method is selected for each region and the manufacturer map is used in design conditions, resulting in a zonal extrapolating approach aiming to preserve accuracy. The transitions between extrapolated zones are corrected, avoiding discontinuities and instabilities.

Reactive computational fluid dynamics modelling of methane–hydrogen admixtures in internal combustion engines: Part I – RANS

2020 ◽  
pp. 146808742091638
Author(s):  
Jann Koch ◽  
Christian Schürch ◽  
Yuri M Wright ◽  
Konstantinos Boulouchos
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Internal Combustion Engines ◽  
Turbulent Flame ◽  
Internal Combustion ◽  
Flame Speed ◽  
Combustion Engines ◽  
Hydrogen Addition ◽  
Dynamics Modelling ◽  
Modelling Approach

The effects of hydrogen addition to internal combustion engines operated by natural gas/methane has been widely demonstrated experimentally in the literature. Already small hydrogen contents in the fuel show promising benefits with respect to increased engine efficiency, lower CO2 emissions, extended lean operating limits and a higher exhaust gas recirculation tolerance while maintaining the knock resistance of methane. In this article, the influence of hydrogen addition to methane on a spark ignited single cylinder engine is investigated. This article proposes a modelling approach to consider hydrogen addition within three-dimensional reactive computational fluid dynamics in order to establish a framework to gain further insights into the involved processes. Experiments have been performed on a single-cylinder spark-ignition engine situated at a test bed and cater as reference data for validating the proposed reactive computational fluid dynamics modelling approach based around the G-Equation combustion model. Within the course of the first part, crucial aspects relevant to the modelling of the mean engine cycle are highlighted. In this article, a simplified early combustion phase model which considers the transition towards a fully developed turbulent flame following ignition is introduced, along with a second submodel considering combined effects of the walls. The sensitivity of the combustion process towards the modelling approach is presented. The submodels were calibrated for a reference operating point, and a sweep in hydrogen content in the fuel as well as stoichiometric and lean operation has been considered. It is shown that the flame speed coefficient A appearing in the used turbulent flame speed closure, weighting the influence of the turbulent fluctuating speed [Formula: see text], has to be adjusted for different hydrogen contents. The introduced submodels allowed for significant improvement of the in-cylinder pressure and heat release rate evolution throughout all considered operating conditions.

Exhaust Pressure Estimation and Its Application to Detection and Isolation of Turbocharger System Faults for Internal Combustion Engines

2011 ◽  
Vol 134 (2) ◽  
Author(s):  
Yue-Yun Wang ◽  
Ibrahim Haskara
Keyword(s):  
High Speed ◽  
Internal Combustion Engines ◽  
Failure Modes ◽  
Combustion Engine ◽  
Pressure Sensors ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Recirculation Flow ◽  
Model Based

Engine exhaust backpressure is a critical parameter in the calculation of the volumetric efficiency and exhaust gas recirculation flow of an internal combustion engine. The backpressure also needs to be controlled to a presetting limit under high speed and load engine operating conditions to avoid damaging a turbocharger. In this paper, a method is developed to estimate exhaust pressure for internal combustion engines equipped with variable geometry turbochargers. The method uses a model-based approach that applies a coordinate transformation to generate a turbine map for the estimation of exhaust pressure. This estimation can substitute for an expensive pressure sensor, thus saving significant cost for production vehicles. On the other hand, for internal combustion engines that have already installed exhaust pressure sensors, this estimation can be used to generate residual signals for model-based diagnostics. Cumulative sum algorithms are applied to residuals based on multiple sensor fusion, and with the help of signal processing, the algorithms are able to detect and isolate critical failure modes of a turbocharger system.

scholarly journals STAND FOR RESEARCH PARAMETERS OF ELEMENTS OF LUBRICATION SYSTEMS OF HIGH-SPEED INTERNAL COMBUSTION ENGINES

2021 ◽  
pp. 73-79
Author(s):  
D.V. Kurnosenko ◽  
V.P. Savchuk ◽  
E.V. Belousov ◽  
А.К. Dzygar ◽  
A.I. Kotov
Keyword(s):  
High Speed ◽  
Internal Combustion Engines ◽  
Diagnostic System ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Engine Oil ◽  
Operating Parameters ◽  
Combustion Engines ◽  
Lubrication System ◽  
Oil Pump

The issues of studying the operating parameters of the elements of lubrication systems for high-speed internal combustion engines preceded the creation of the stand. The engine lubrication system D-246.4 was chosen as a prototype. With the help of this stand it became possible to study the lubrication system for the following characteristics: change the performance of the engine oil pump D-246.4, change and control the engine oil temperature, control the pressure drop on the oil filter, control the engine oil flow, throttle oil at the inlet to the oil pump and on the conditional supply line to the friction units, measuring the vacuum of the system on the suction of the oil pump and recording the parameters of the pulsation of the oil pressure generated by the oil pump. To build mathematical models of the components in the lubrication systems of marine internal combustion engines there is a need to determine their operating parameters. In real operating conditions, such measurements cannot be obtained due to the lack of the necessary test equipment (TE) and the possibility of its installation. The authors describe in detail all the components of the stand for studying the parameters of the elements of lubrication systems of high-speed internal combustion engines, their technical characteristics, describes the diagnostic complex, which recorded the results of research, the results of measuring engine oil pressure pulsation. The stand is used to study the operating parameters of the oil pump and filter used for water. Signals are registered using the Autoscanner diagnostic system. The diagnostic complex is a 64-channel oscilloscope that is connected to a personal computer. This stand for studying the operating parameters of the elements of the lubrication system provides sufficient opportunities to simulate the operating conditions of the elements of the supply and purification of oil and register them both visually and with digital sensors and diagnostic system Autoscanner, digital oscilloscopes or other measuring instruments capable of recording and storing the received data.

scholarly journals THE COMBUSTION ENGINE INTAKE MANIFOLD CFD MODELING DEPENDING ON THE AIRBOX CONFIGURATION

2021 ◽  
Vol 2021 (6) ◽  
pp. 5421-5425
Author(s):  
MICHAL RICHTAR ◽  
◽  
PETRA MUCKOVA ◽  
JAN FAMFULIK ◽  
JAKUB SMIRAUS ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Stationary Flow ◽  
Cfd Modeling ◽  
Intake Manifold ◽  
Combustion Engines ◽  
Computational Fluid Dynamics Cfd

The aim of the article is to present the possibilities of application of computational fluid dynamics (CFD) to modelling of air flow in combustion engine intake manifold depending on airbox configuration. The non-stationary flow occurs in internal combustion engines. This is a specific type of flow characterized by the fact that the variables depend not only on the position but also on the time. The intake manifold dimension and geometry strongly effects intake air amount. The basic target goal is to investigate how the intake trumpet position in the airbox impacts the filling of the combustion chamber. Furthermore, the effect of different distances between the trumpet neck and the airbox wall in this paper will be compared.

scholarly journals The influence of centrial forces on crankshaft bearing lubrication is in emergency modes of the engine of the car

2021 ◽  
Vol 12 (2) ◽  
pp. 112-121
Author(s):  
Oleksandr Khrulev ◽  
◽  
Olexii Saraiev ◽  
Iryna Saraieva ◽  
◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Operating Mode ◽  
Internal Combustion ◽  
Technical Condition ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Connecting Rod ◽  
Oil Supply ◽  
Technical Expert ◽  
The Difference

The analysis of the crankshaft bearing condition of the automotive internal combustion engines in the case of insufficiency and breakage of oil supply to them is carried out. It is noted that this fault is one of the most common causes of damage to rubbing pairs in operation. At the same time, the different groups of bearings are often damaged, which cannot be explained within the framework of existing models of plain bearing lubrication. The objective of the work is to develop a mathematical model of oil supply to connecting rod bearings in emergency mode, taking into account the characteristic features of the bearing design. The model also, depending on the nature of the damage, should help to determine and explain the causes of bearing failures if they occur in different modes when operating conditions are broken. A computational model has been developed that makes it possible to assess the effect of design differences in the features of oil supply and the action of the centrifugal forces during crankshaft rotation on the oil column in the lubrication hole where oil is supplied to the conrod bearing. Calculations of the change in time of the oil supply pressure to the connecting rod bearings for the various designs of the crankshaft lubrication holes have been performed. It is shown that, depending on the operating mode of the engine and its design, the oil pressure in front of the connecting rod bearings does not disappear immediately after oil supply failure to crankshaft. Moreover, the lower the crankshaft speed is, the longer the lubrication of the conrod bearings will continue. The calculation results are confirmed by the data of the expert studies of the engine technical condition, in which the crankshaft was wedged in the damaged main bearings was found in the absence of serious damage to the connecting rod ones. It has been found that such features of the damage correspond to an rapid breakage of the oil supply to the crankshaft in the case of such operational damage as the oil pump and pressure reducing valve failure, the oil filter seal and oil pan destruction, etc. The developed model explains the difference in lubrication conditions and in the damage feature to the main and connecting rod bearings in the emergency cases of the oil supply breakage, which are observed during operation, and helps to clarify the failure causes. This makes it possible to use the model and the obtained data when providing auto technical expert studies of the failure causes of automobile internal combustion engines This makes it possible to use the model and the obtained data when providing auto technical expert studies of the failure causes of automobile internal combustion engines when the operating conditions are broken.

Compressor Design for Multi-Point Operating Conditions of Turbocharged Gasoline Engines

2010 ◽  
Author(s):  
Tao Chen ◽  
Yangjun Zhang ◽  
Xinqian Zheng ◽  
Weilin Zhuge
Keyword(s):  
Internal Combustion Engines ◽  
Gasoline Engine ◽  
Design Method ◽  
Pressure Ratio ◽  
Operating Conditions ◽  
Combustion Engines ◽  
Gasoline Engines ◽  
Compressor Design ◽  
Operating Points ◽  
Load Conditions

Turbocharger compressor design is a major challenge for performance improvement of turbocharged internal combustion engines. This paper presents a multi-point design methodology for turbocharger centrifugal compressors. In this approach, several design operating condition points of turbocharger compressor are considered according to total engine system requirements, instead of one single operating point for traditional design method. Different compressor geometric parameters are selected and investigated at multi-point operating conditions for the flow-solutions of different design objectives. The method has been applied with success to a small centrifugal compressor design of a turbocharged gasoline engine. The results show that the consideration of several operating points is essential to improve the aerodynamic behavior for the whole working range. The isentropic efficiency has been increased by more than 5% at part-load conditions while maintaining the pressure ratio and flow range at full-load conditions of the gasoline engine.

Sign in / Sign up

Export Citation Format

Share Document