Large-eddy simulation of direct injection natural gas combustion in a heavy-duty truck engine using modified conditional moment closure model with low-dimensional manifold method

2018 ◽  
Vol 21 (5) ◽  
pp. 824-837 ◽  
Author(s):  
Jian Huang ◽  
Gordon McTaggart-Cowan ◽  
Sandeep Munshi

This article describes the application of a modified first-order conditional moment closure model used in conjunction with the trajectory-generated low-dimensional manifold method in large-eddy simulation of pilot ignited high-pressure direct injection natural gas combustion in a heavy-duty diesel engine. The article starts with a review of the intrinsic low-dimensional manifold method for reducing detailed chemistry and various formulations for the construction of such manifolds. It is followed by a brief review of the conditional moment closure method for modelling the interaction between turbulence and combustion chemistry. The high computational cost associated with the direct implementation of the basic conditional moment closure model was discussed. The article then describes the formulation of a modified approach to solve the conditional moment closure equation, whose reaction source terms for the conditional mass fractions for species were obtained by projecting the turbulent perturbation onto the reaction manifold. The main model assumptions were explained and the resulting limitations were discussed. A numerical experiment was conducted to examine the validity the model assumptions. The model was then implemented in a combustion computational fluid dynamics solver developed on an open-source computational fluid dynamics platform. Non-reactive jet simulations were first conducted and the results were compared to the experimental measurement from a high-pressure visualization chamber to verify that the jet penetration under engine relevant conditions was correctly predicted. The model was then used to simulate natural gas combustion in a heavy-duty diesel engine equipped with a high-pressure direct injection system. The simulation results were compared with the experimental measurement from a research engine to verify the accuracy of the model for both the combustion rate and engine-out emissions.

2019 ◽  
Vol 21 (3) ◽  
pp. 497-513 ◽  
Author(s):  
Jeremy Rochussen ◽  
Gordon McTaggart-Cowan ◽  
Patrick Kirchen

Natural gas is an attractive fuel for internal combustion engines in light of its potential for reduced greenhouse gas and particulate emissions, and significant reserves. To facilitate natural gas use in compression ignition engines, pilot-ignited direct-injection natural gas combustion uses a small pilot injection of diesel to ignite a more significant direct injection of natural gas. Compared to modern diesel combustion, this strategy is a promising technology for the reduction of CO2 emissions while retaining diesel-like efficiency without a significant CH4 emission penalty. To further develop this technology, investigation of in-cylinder combustion processes is needed to identify the primary fuel conversion processes. The objective of this work was to provide a framework of conceptual understanding by identifying key processes in a typical pilot-ignited direct-injection natural gas combustion event and characterizing their sensitivity to fuel injection parameters. A parametric sweep of injection pressure, natural gas injection duration, and relative timing of the diesel pilot and natural gas injections was performed in an optically accessible 2 L single-cylinder engine. Combined heat release rate and OH*-chemiluminescence reaction zone analysis was used to demarcate the transition from ignition reactions to primary natural gas heat release. Five distinct combustion processes were identified: (1) pilot auto-ignition; (2) natural gas ignition; (3) rapid, distributed partially premixed natural gas combustion; (4) non-premixed combustion; and (5) late-cycle oxidation. While natural gas ignition was found to be insensitive to injection pressure, it was strongly affected by the time between pilot and natural gas injections. Reducing the relative injection timing from +8° to −6° resulted in the primary natural gas heat release transitioning from non-premixed, to distributed partially premixed, to stratified premixed flame propagation as a result of increasing natural gas premixing. The presented measurements and analysis serve to refine an initial conceptual model of the combustion process and lay the groundwork for future, more focused studies of pilot-ignited, direct-injection natural gas combustion.


2019 ◽  
Vol 6 (2) ◽  
pp. 56-63
Author(s):  
L. D. Pylypiv ◽  
І. І. Maslanych

There are investigated the influence of operating pressures in the gas supply system on the level of such energy indicators as efficiency, gas flow and gas overrun by gas equipment in residential buildings. There is established a relationship between the values of operating pressures in the gas supply system and the gas consumption level of household appliances. The causes of insufficient pressure in the gas networks of settlements are analyzed in the article. There is also developed an algorithm for calculating the change in the efficiency of gas appliances depending on the operational parameters of the gas network. It has been found that the most efficient operation of gas appliances is observed at an overpressure at the inlet of gas appliances of about 1200 Pa.To ensure the required quality of natural gas combustion among consumers and minimize gas consumption there are justified the following measures in the article: coordinating a domestic regulatory framework for assessing the quality of natural gas with international norms and standards; improving the preparation of gas coming from local wells before supplying it to gas distribution networks; auditing low pressure gas pipelines and reconstructing areas affected by corrosion; ensuring standard gas pressure in the network for the normal operation of domestic gas appliances; stating quality indicators of natural gas combustion by gas sales organizations.


Sign in / Sign up

Export Citation Format

Share Document