scholarly journals Initial rotational stiffness of minor-axis flush end-plate connections

2018 ◽  
Vol 10 (1) ◽  
pp. 168781401774539
Author(s):  
Jianrong Pan ◽  
Shizhe Chen ◽  
Zhan Wang ◽  
Hui Lu
Keyword(s):  
Finite Element ◽  
Minor Axis ◽  
Bottom Flange ◽  
Rotational Stiffness ◽  
Bending Deformation ◽  
End Plate ◽  
Out Of Plane ◽  
Plane Bending ◽  
Plate Connections ◽  
Plate Connection

The semi-rigid performance of minor-axis connections is important in the study of overall framework. Experiments were conducted on minor-axis flush end-plate connections under a monotonic load. Numerical simulations were carried out using the finite-element package ABAQUS and compared with the experimental results. The initial rotational stiffness of the connection was calculated using the equivalent T-stub in tension and EC3 component method, and the calculated veracity is discussed. The results show that under the action of a negative bending moment, the failure modes of the minor-axis flush end-plate connection are the out-of-plane bending deformation of the end-plate, local buckling of the bottom flange of the beam, and bending deformation of the bolts. The minor-axis flush end-plate connection is a typical semi-rigid connection. However, the deformations of the flush end-plate could not be accurately calculated using the equivalent T-stub in the tension of EC3 methods. The initial rotational stiffness calculated using the method was much larger than that obtained using the experiment and finite-element analysis. The equivalent simulation is not appropriate if the out-of-plane bending stiffness of the flush end-plate is not obtained accurately.

scholarly journals Verification of prying effect in prestressed end-plate connection

2013 ◽  
Vol 12 (2) ◽  
pp. 251-258
Author(s):  
Krzysztof Ostrowski ◽  
Jan Łaguna ◽  
Aleksander Kozłowski
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
High Strength ◽  
Experimental Tests ◽  
Analytical Models ◽  
End Plate ◽  
Plate Connections ◽  
Plate Connection ◽  
Element Method

End-plate connections are very often used is steelwork, as tension and bending connections. As a result of deflection of end plate, additional forces, known as prying forces arise and consequently increase stresses in bolts. Eurocode 1993-1-8 do not distinguish end-plate connections prestressed by high strength bolts from non-prestressed. The aim of the paper is to perform the comparison of previous analytical models and code regulations for coefficient of prying forces to the experimental tests and modelling by finite element method. Results of the analysis show that the behaviour of prestressed connection is essentially different with comparison to non-prestressed.

Three-dimensional numerical and linearly distributed multi-parameter fitted analytical modeling of hybrid beam–column with partially welded flush end-plate connection

2018 ◽  
Vol 21 (12) ◽  
pp. 1777-1791
Author(s):  
Joma HM Omer ◽  
Ahmad BH Kueh ◽  
Poi-Ngian Shek
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Flexural Behavior ◽  
Major Influence ◽  
End Plate ◽  
Hybrid Beams ◽  
Plate Connections ◽  
Plate Connection ◽  
Three Dimensional Finite Element

The flexural behavior of partially welded flush end-plate connections incorporating built-up hybrid beams and columns is analytically and numerically investigated. An experimentally obeying three-dimensional finite element model is first constructed. To circumvent the laborious effort of three-dimensional simulation and experimental work, a new experimentally and numerically complying equation approach is introduced for the construction of a continuous moment–rotation ( M–θ) description. For the proposed equation, two essential terms are required: the rotational stiffness, Sj,ini, obtained by employing the component method and the maximum moment, Mmax, produced using the proposed linearly distributed multi-parameter fitting technique. To demonstrate the applicability of the proposed equation, a variation in the geometric configuration of connections within the practical range is considered. Excellent agreement is noted when comparing all M–θ relationships produced by the proposed equation to those by the finite element method and experiments. In addition, the stress distribution and main deformation modes are numerically obtained, where the ranking of stress criticality is offered for all structural parts. The depth, width, flange, and web thicknesses, as well as the yield stress of the beam, have a major influence on Mmax, as predicted by the proposed equation. Also, bolts have been identified as the most critically stressed component.

scholarly journals Analysis of the Mechanical Behavior of Bolted Beam-Column Connections with Different Structural Forms

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Rongqian Yang ◽  
Xuejun Zhou
Keyword(s):  
Finite Element ◽  
Mechanical Behavior ◽  
Simulation Analysis ◽  
Element Model ◽  
Hysteretic Behavior ◽  
Load Bearing ◽  
End Plate ◽  
Extended End Plate ◽  
Plate Connections ◽  
Plate Connection

In order to study the mechanical behavior of bolted beam-column connections, the accuracy and applicability of the finite element model were firstly validated according to the published experiments on end-plate connections using ABAQUS. Then, in order to discuss the mechanical behavior of connections, three semirigid connections which are convenient for prefabricated construction, including top-and-seat angle connections with web and ear plate, extended end-plate connection, and T-stub connection, were examined using numerical simulation analysis to study and compare their capacity, hysteretic behavior, ductility, and degradation characteristics in detail. The results showed that the finite element models that were built could effectively simulate the load bearing behavior of bolted connections under both single-direction loading and cyclic loading. The three connections showed good load bearing capacity. The connectors significantly affected the energy dissipation capacity under load. The extended end-plate connection demonstrated the best performance in both mechanical behavior and manufacture and installation, so it would therefore be the preferred option.

Numerical studies on the structural behaviour of composite end-plate connections

2010 ◽  
Vol 37 (6) ◽  
pp. 907-921 ◽  
Author(s):  
Aaron J. Wang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Three Dimensional ◽  
Element Model ◽  
Structural Behaviour ◽  
Analysis And Design ◽  
Shear Connectors ◽  
End Plate ◽  
Plate Connections ◽  
Plate Connection

A three-dimensional (3-D) finite element model is established to predict the structural behaviour of composite end-plate connections with full incorporation of material and geometrical nonlinearities. A two-dimensional (2-D) finite element model is also proposed as a tool for a comprehensive parametric study, analysis, and design. The accuracy of both the models is verified by comparing the numerical results with those from tests and a design model. Various important structural behaviours of composite end-plate connection are also studied through the numerical and analytical simulations. These models are regarded as effective tools for conducting performance-based design of composite connections and semi-continuous beams with reasonable consideration of nonlinear deformation characteristics of both tensile reinforcements and shear connectors.

Model of the Initial Stiffness in Extended End-Plate Connection

2013 ◽  
Vol 321-324 ◽  
pp. 1766-1769
Author(s):  
Jian Li Zhao
Keyword(s):  
Great Influence ◽  
Order Effects ◽  
Lateral Stiffness ◽  
Rotational Stiffness ◽  
Initial Stiffness ◽  
End Plate ◽  
Extended End Plate ◽  
Plate Connections ◽  
Plate Connection ◽  
Frame Stiffness

Extend end-plat bolted connections are widely used in steel frames. The rotational stiffness has great influence on steel frame stiffness and deformation. The decrease of the frame lateral stiffness, due to connection rotational deformability, leads to the increase of the period of vibration and the frame sensitivity to second-order effects. This thesis divides the end plate into several parts equivalent to different Timoshenkos beams to determine their contribution to rotational stiffness of the connection. Then stiffness of all parts and bolts is given, and then the component method is used to calculate rotational initial stiffness of extended end-plate connections. Comparisons with results of ANSYS and related tests show that the proposed equations have excellent precision. And the calculating process is simple and easily applicable in practice.

Analysis on the Seismic Behavior of Extended End-Plate Connections of Steel Frame Structure

2012 ◽  
Vol 193-194 ◽  
pp. 1405-1413 ◽  
Author(s):  
Zhu Ling Yan ◽  
Bao Long Cui ◽  
Ke Zhang
Keyword(s):  
Finite Element ◽  
Cyclic Loading ◽  
Seismic Performance ◽  
Seismic Behavior ◽  
Frame Structure ◽  
End Plate ◽  
Rigid Connection ◽  
Extended End Plate ◽  
Plate Connections ◽  
Steel Frame Structure

This paper conducts analysis on beam-column extended end-plate semi-rigid connection joint concerning monotonic loading and cyclic loading of finite element through ANSYS program, mainly discussed the influence of parameters such as the form of end plate stiffening rib on anti-seismic performance of joint.

Structural Behaviour of Blind Bolted Connection to Concrete-Filled Steel Tubular Columns

2010 ◽  
Vol 163-167 ◽  
pp. 591-595
Author(s):  
Jing Feng Wang ◽  
Xin Yi Chen ◽  
Lin Hai Han
Keyword(s):  
Analysis Model ◽  
Bolted Connections ◽  
Structural Behaviour ◽  
Tubular Columns ◽  
End Plate ◽  
Moment Resisting ◽  
Strength And Stiffness ◽  
Plate Connections ◽  
The Moment ◽  
Plate Connection

This paper studies structural behaviour of the blind bolted connections to concrete-filled steel tubular columns by a serial of experimental programs, which conducted involving eight sub-assemblages of cruciform beam-to-column joints subjected to monotonic loading and cyclic loading. The moment-rotation hysteretic relationships and failure models of the end plate connections have been measured and analyzed. A simplified analysis model for the blind bolted connections is proposed based on the component method. It is concluded that the blind bolted end plate connection has reasonable strength and stiffness, whilst the rotation capacity of the connection satisfies the ductility requirements for earthquake-resistance in most aseismic regions. This typed joint has excellent seismic performance, so it can be used in the moment-resisting composite frame.

scholarly journals Stress Distribution Analysis of DKDT Tubular Joint in a Minimum Offshore Structure

Rekayasa ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 191-199
Author(s):  
Irma Noviyanti ◽  
Rudi Walujo Prastianto ◽  
Murdjito Murdjito
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Axial Force ◽  
Oil And Gas ◽  
Bending Moment ◽  
Out Of Plane ◽  
Tubular Joint ◽  
Plane Bending ◽  
Intersection Line ◽  
Marginal Field

A marginal field defines as an oil and/or gas field that has a short production period, low proven reservoir, and could not be exploited using existing technology. As the demand for oil and gas keeps increasing, one of the solutions to tackle the issues is to build the modified platform which came to be more minimalist to conduct the oil and gas production in the marginal field. Naturally, the minimum offshore structures are cost less but low in redundancy, therefore, pose more risks. Although the study on the minimum structures is still uncommon, there are opportunities to find innovative systems that need to have a further analysis toward such invention. Therefore, this study took the modified jacket platform as a minimum structure, and local stresses analysis by using finite element method is applied for the most critical tubular joint with multiplanarity of the joint is taking into account. The analysis was carried out using the finite element program of Salome Meca with three-dimensional solid elements are used to model the multiplanar joint. Various loading types of axial force, in-plane bending moment, and out-of-plane bending moment are applied respectively to investigate the stress distribution along the brace-chord intersection line of the tubular joint. The results show that the hotspot stress occurred at a different point along each brace-chord intersection line for each loading type. Finally, as compared to the in-plane bending moment or out-of-plane bending moment loading types, the axial force loading state is thought to generate greater hotspot stress.

Sign in / Sign up

Export Citation Format

Share Document