The experimental study of a miniature high-speed gas-bearing expansion turbine

2011 ◽  
Vol 225 (3) ◽  
pp. 319-326 ◽  
Author(s):  
R G Chen ◽  
Y Liu ◽  
Y Hou ◽  
G Xi
Keyword(s):  
Experimental Study ◽  
High Speed ◽  
Expansion Turbine ◽  
Gas Bearing

Experimental study of three—titling—pad self—acting journal gas bearing expansion turbine

Cryogenics ◽  
1992 ◽  
Vol 32 ◽  
pp. 76-79 ◽  
Author(s):  
Chunzheng Chen ◽  
Zhihai Dong ◽  
Guining Cui ◽  
Yuyuan Wu ◽  
Runquan Tang ◽  
...  
Keyword(s):  
Experimental Study ◽  
Expansion Turbine ◽  
Gas Bearing

Experimental study on laminated glass responses of high-speed trains subject to windblown sand particles loading

2021 ◽  
Vol 300 ◽  
pp. 124332
Author(s):  
Gongxun Deng ◽  
Wen Ma ◽  
Yong Peng ◽  
Shiming Wang ◽  
Song Yao ◽  
...  
Keyword(s):  
Experimental Study ◽  
High Speed ◽  
Laminated Glass ◽  
Windblown Sand ◽  
High Speed Trains ◽  
Sand Particles

Experimental Study of Turbulent Macroinstabilities in an Agitated System with Axial High-Speed Impeller and with Radial Baffles

1996 ◽  
Vol 61 (6) ◽  
pp. 856-867 ◽  
Author(s):  
Oldřich Brůha ◽  
Ivan Fořt ◽  
Pavel Smolka ◽  
Milan Jahoda
Keyword(s):  
Experimental Study ◽  
Flow Field ◽  
High Speed ◽  
Experimental Results ◽  
Turbulent Regime ◽  
Frequency Of Occurrence ◽  
Visualization Method ◽  
Entire Flow

The frequency of turbulent macroinstability occurrence was measured in liquids agitated in a cylindrical baffled vessel. As it has been proved by preceding experimental results of the authors, the stochastic quantity with frequency of occurrence of 10-1 to 100 s-1 is concerned. By suitable choosing the viscosity of liquids and frequency of impeller revolutins, the region of Reynolds mixing numbers was covered from the pure laminar up to fully developed turbulent regime. In addition to the equipment making it possible to record automatically the macroinstability occurrence, also the visualization method and videorecording were employed. It enabled us to describe in more detail the form of entire flow field in the agitated system and its behaviour in connection with the macroinstability occurrence. It follows from the experiments made that under turbulent regime of flow of agitated liquids the frequency of turbulent macroinstability occurrence is the same as the frequency of the primary circulation of agitated liquid.

scholarly journals Pivoted-Pad Journal Gas Bearing Performance in Exploratory Operation of Brayton Cycle Turbocompressor

1968 ◽  
Vol 90 (4) ◽  
pp. 687-696 ◽  
Author(s):  
R. Y. Wong ◽  
W. L. Stewart ◽  
H. E. Rohlik
Keyword(s):  
Experimental Study ◽  
Journal Bearing ◽  
Inert Gas ◽  
Brayton Cycle ◽  
Ambient Conditions ◽  
Operating Characteristics ◽  
The Third ◽  
Loading Device ◽  
Bearing Design ◽  
Gas Bearing

This paper describes findings obtained to date in the area of journal gas bearings from an experimental study of a Brayton cycle turbocompressor designed for the requirements of a two-shaft 10-kw space power system. The journal bearing design utilizes three pads pivoted on conforming balls and sockets. Two of the pivots are rigidly mounted to the frame, and the third pivot is mounted to the frame through a low-spring-rate diaphragm. This paper describes the salient package and bearing design features and then presents the principal results obtained from testing the package in both a spin calibration rig and operation at design temperature conditions with an inert gas. The results discussed include (a) the successful use of a pneumatic loading device to vary pad load during operation, (b) the operating characteristics of the bearings as obtained over a range of pad loads and ambient conditions, (c) structural and dynamic behavior of the bearing-support system during design temperature operation and (d) a discussion of the wear characteristics of the conforming ball-and-socket pivot as obtained from the tests made to date.

scholarly journals Study and Analysis of Anti Vibratory Passive and Active Methods Applied to Complex Mechanical System

2012 ◽  
Vol 7 (2) ◽  
Author(s):  
Cédric Lopez ◽  
François Malburet ◽  
André Barraco
Keyword(s):  
Experimental Study ◽  
Comparative Analysis ◽  
Mechanical System ◽  
High Speed ◽  
Test Bench ◽  
Minimization Method ◽  
Controlled System ◽  
Proper Frequency ◽  
Different Parts ◽  
Methods Of Control

This paper studies problematic of a mechanical system composed of different coupled parts submitted to a high speed shock and proposes analysis of anti vibratory passive and active methods based on an experimental and theoretical coupled approach. After a shock, different parts of the system oscillate. If one of them is excited at a particular frequency, such as its proper frequency, important oscillations appear and can lead to the deterioration of the system by introducing important stresses. In this paper, we propose an analysis in order to understand this kind of problem and what we can do to avoid it. Firstly, we discuss problematic and we expose the studied system. In a second time, we develop two approaches of modeling that allow us to understand the phenomenon by carrying out numerical simulations. Then cross checking of model is completed via experimental study on drop test bench. Passive minimization method of vibrations based on experimental and theoretical coupled approach is exposed. Finally, a comparative analysis of different methods of control and experimental results of controlled system are presented.

Effects of Cutting Parameters on Residual Stresses in High-Speed Milling of Ti-17

2013 ◽  
Vol 834-836 ◽  
pp. 861-865 ◽  
Author(s):  
Yong Shou Liang ◽  
Jun Xue Ren ◽  
Yuan Feng Luo ◽  
Ding Hua Zhang
Keyword(s):  
Experimental Study ◽  
Residual Stresses ◽  
High Speed ◽  
Experimental Parameter ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Single Factor ◽  
Cutting Depth ◽  
High Speed Milling ◽  
Parameter Ranges

An experimental study was conducted to determine cutting parameters of high-speed milling of Ti-17 according to their effects on residual stresses. First, three groups of single factor experiments were carried out to reveal the effects of cutting parameters on residual stresses. Then sensitivity models were established to evaluate the influence degrees of cutting parameters on residual stresses. After that, three criteria were proposed to determine cutting parameters from experimental parameter ranges. In the experiments, the cutting parameter ranges are recommended as [371.8, 406.8] m/min, [0.363, 0.412] mm and [0, 0.018] mm/z for cutting speed, cutting depth and feed per tooth, respectively.

Sign in / Sign up

Export Citation Format

Share Document