Relationship between composition, impurity content, cooling rate, and solidification in austenitic stainless steels

The effects of chemical composition and cooling rate on the delta ferrite formation in austenitic stainless steels have been investigated. Ferrite fractions measured by a magnetic method were in the range of 0 to 12% and were compared with those calculated by empirical formulas available in the literature. The delta ferrite formation (amount and distribution) was strongly affected by the steel chemical composition, but less affected by the cooling rate. Among several formulas used to calculate the amount of delta ferrite, the best agreement was obtained with those proposed independently by Schneider and Schoefer, the latter being recommended in the ASTM 800 standard.

Download Full-text

Study on the effect of nitrogen content and cooling rate on the ferrite number of austenitic stainless steels

International Journal of Advanced Engineering Research and Science ◽

10.22161/ijaers.711.34 ◽

2020 ◽

Vol 7 (11) ◽

pp. 270-277

Author(s):

André de Albuquerque Vicente ◽

Peter Aloysius D'silva ◽

Sibi Sadanandan ◽

Tiago Felipe de Abreu Santos ◽

Jorge Alberto Soares Tenório

Keyword(s):

Nitrogen Content ◽

Cooling Rate ◽

Stainless Steels ◽

Austenitic Stainless Steels ◽

Ferrite Number

Download Full-text

Radiation Damage Studies with the HVEM

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100096655 ◽

1972 ◽

Vol 30 ◽

pp. 680-681

Author(s):

J. J. Laidler ◽

B. Mastel

Keyword(s):

Radiation Damage ◽

Stainless Steels ◽

Volume Expansion ◽

Austenitic Stainless Steels ◽

Test Facility ◽

Fast Breeder Reactors ◽

Breeder Reactors ◽

Under Construction ◽

Development Laboratory ◽

Insight Into

One of the major materials problems encountered in the development of fast breeder reactors for commercial power generation is the phenomenon of swelling in core structural components and fuel cladding. This volume expansion, which is due to the retention of lattice vacancies by agglomeration into large polyhedral clusters (voids), may amount to ten percent or greater at goal fluences in some austenitic stainless steels. From a design standpoint, this is an undesirable situation, and it is necessary to obtain experimental confirmation that such excessive volume expansion will not occur in materials selected for core applications in the Fast Flux Test Facility, the prototypic LMFBR now under construction at the Hanford Engineering Development Laboratory (HEDL). The HEDL JEM-1000 1 MeV electron microscope is being used to provide an insight into trends of radiation damage accumulation in stainless steels, since it is possible to produce atom displacements at an accelerated rate with 1 MeV electrons, while the specimen is under continuous observation.

Download Full-text

Strain-induced martensite effects on transgranular carbide precipitation in type 304 stainless steels

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100087331 ◽

1991 ◽

Vol 49 ◽

pp. 604-605

Author(s):

A.H. Advani ◽

L.E. Murr ◽

D. Matlock

Keyword(s):

Heat Treatment ◽

Grain Boundary ◽

Stress Corrosion Cracking ◽

Stainless Steels ◽

Deformation Twin ◽

Austenitic Stainless Steels ◽

Carbide Precipitation ◽

Strain Induced Martensite ◽

Type 304

Thermomechanically induced strain is a key variable producing accelerated carbide precipitation, sensitization and stress corrosion cracking in austenitic stainless steels (SS). Recent work has indicated that higher levels of strain (above 20%) also produce transgranular (TG) carbide precipitation and corrosion simultaneous with the grain boundary phenomenon in 316 SS. Transgranular precipitates were noted to form primarily on deformation twin-fault planes and their intersections in 316 SS.Briant has indicated that TG precipitation in 316 SS is significantly different from 304 SS due to the formation of strain-induced martensite on 304 SS, though an understanding of the role of martensite on the process has not been developed. This study is concerned with evaluating the effects of strain and strain-induced martensite on TG carbide precipitation in 304 SS. The study was performed on samples of a 0.051%C-304 SS deformed to 33% followed by heat treatment at 670°C for 1 h.

Download Full-text

Oxidation behavior of 26Cr-16Ni and AISI 309 austenitic stainless steels in air flow at 1,173 K

Materials Testing ◽

10.3139/120.110753 ◽

2015 ◽

Vol 57 (7-8) ◽

pp. 597-601 ◽

Cited By ~ 1

Author(s):

Peeraya Pipatnukun ◽

Panyawat Wangyao ◽

Gobboon Lothongkum

Keyword(s):

Stainless Steels ◽

Oxidation Behavior ◽

Air Flow ◽

Austenitic Stainless Steels

Download Full-text

EPRI P87

Alloy Digest ◽

10.31399/asm.ad.ni0685 ◽

2011 ◽

Vol 60 (1) ◽

Keyword(s):

Fracture Toughness ◽

Tensile Properties ◽

Stainless Steels ◽

Austenitic Stainless Steels

Abstract EPRI P87 is a MMA electrode designed for dissimilation joints between austenitic stainless steels (i.e. 304H) and a creep resisting CrMo alloy (i.e. P91). This datasheet provides information on composition and tensile properties as well as fracture toughness. It also includes information on joining. Filing Code: Ni-685. Producer or source: Metrode Products Ltd.

Download Full-text

CARPENTER STAINLESS 304+B

Alloy Digest ◽

10.31399/asm.ad.ss0121 ◽

1961 ◽

Vol 10 (9) ◽

Keyword(s):

Fracture Toughness ◽

Cross Section ◽

Stainless Steels ◽

Austenitic Stainless Steels ◽

Heat Treating ◽

Neutron Absorption ◽

Absorption Cross ◽

Type 304 ◽

Conventional Type ◽

Neutron Absorption Cross Section

Abstract Carpenter Stainless 304+B is similar to conventional Type 304 with the addition of boron to give it a much higher thermal neutron absorption cross-section than other austenitic stainless steels. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SS-121. Producer or source: Carpenter.

Download Full-text

ALZ 316

Alloy Digest ◽

10.31399/asm.ad.ss0756 ◽

1999 ◽

Vol 48 (8) ◽

Keyword(s):

Mechanical Properties ◽

Stainless Steel ◽

Corrosion Resistance ◽

Austenitic Stainless Steel ◽

Physical Properties ◽

Tensile Properties ◽

Stainless Steels ◽

Austenitic Stainless Steels ◽

Heat Treating

Abstract ALZ 316 is an austenitic stainless steel with good formability, corrosion resistance, toughness, and mechanical properties. It is the basic grade of the stainless steels, containing 2 to 3% molybdenum. After the 304 series, the molybdenum-containing stainless steels are the most widely used austenitic stainless steels. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-756. Producer or source: ALZ nv.

Download Full-text