scholarly journals Flow Control for a Two-Stage Proportional Valve with Hydraulic Position Feedback

2020 ◽  
Vol 33 (1) ◽  
Author(s):  
He Wang ◽  
Xiaohu Wang ◽  
Jiahai Huang ◽  
Long Quan
Keyword(s):  
Mathematical Model ◽  
Flow Control ◽  
Control Method ◽  
Two Stage ◽  
Proportional Valve ◽  
Load Pressure ◽  
Flow Fluctuation ◽  
Position Feedback ◽  
Proportional Flow ◽  
Flow Valve

AbstractThe current research mainly focuses on the flow control for the two-stage proportional valve with hydraulic position feedback which is named as Valvistor valve. Essentially, the Valvistor valve is a proportional throttle valve and the flow fluctuates with the change of load pressure. The flow fluctuation severely restricts the application of the Valvistor valve. In this paper, a novel flow control method the Valvistor valve is provided to suppress the flow fluctuation and develop a high performance proportional flow valve. The mathematical model of this valve is established and linearized. Fuzzy proportional-integral-derivative (PID) controller is adopted in the closed-loop flow control system. The feedback is obtained by the flow inference with back-propagation neural network (BPNN) based on the spool displacement in the pilot stage and the pressure differential across the main orifice. The results show that inference with BPNN can obtain the flow data fast and accurately. With the flow control method, the flow can keep at the set point when the pressure differential across the main orifice changes. The flow control method is effective and the Valvistor valve changes from proportional throttle valve to proportional flow valve. For the developed proportional flow valve, the settling time of the flow is very short when the load pressure changes abruptly. The performances of hysteresis, linearity and bandwidth are in a high range. The linear mathematical model can be verified and the assumptions in the system modeling is reasonable.

Performance Improvement of a Two-Stage Proportional Valve With Internal Hydraulic Position Feedback

2021 ◽  
Vol 143 (7) ◽  
Author(s):  
He Wang ◽  
Xiaohu Wang ◽  
Jiahai Huang ◽  
Long Quan
Keyword(s):  
Performance Improvement ◽  
Control Strategy ◽  
Dead Zone ◽  
Poor Performance ◽  
Main Stage ◽  
Two Stage ◽  
Proportional Valve ◽  
Loop Control ◽  
Position Feedback ◽  
Performance Constraint

Abstract The present research concentrates on the performance improvement of a two-stage proportional valve with internal hydraulic position feedback which is named as the Valvistor valve. In this paper, the performance constraint of this valve is identified and a novel electronic closed-loop control strategy with an integral-separation fuzzy proportional-integral-derivative controller is proposed to improve the valve performance, including the static characteristics and the dynamic characteristics. The results show that in the Valvistor valve, the comparison point and the feedback loop for the internal hydraulic position feedback is only in the main stage, while the input is in the pilot stage. This leads to the poor performance of this valve. The control strategy is very effective and the performance of the Valvistor valve is improved. With the control strategy, the error of the poppet displacement is reduced from 4.9% to 2.1% by adjusting the spool displacement in the pilot stage in real-time and the flow error is reduced from 5.3% to 2.3%. The dead zone of the poppet displacement and the flow is eliminated. The hysteresis is reduced from 5.3% to 2.6% and the linearity is improved. The overshoot is reduced from 0.06 to 0.02 mm and the settling time is reduced from 0.5 to 0.2 s. Moreover, the bandwidth is increased from 8 to 16 Hz.

Power-Flow Control Method for Wireless In-Wheel Motor with Supercapacitor

2018 ◽  
Vol 138 (3) ◽  
pp. 219-226
Author(s):  
Takuma Takeuchi ◽  
Takehiro Imura ◽  
Daisuke Gunji ◽  
Hiroshi Fujimoto ◽  
Yoichi Hori
Keyword(s):  
Flow Control ◽  
Power Flow ◽  
Control Method ◽  
Power Flow Control

scholarly journals Improved Feeder Flow Control Method for a Virtual Power Plant With Various Resources to Reduce Communication Dependency

IEEE Access ◽  
2020 ◽  
Vol 8 ◽  
pp. 206820-206834
Author(s):  
Jae-Won Chang ◽  
Hee Seung Moon ◽  
Seung-Il Moon ◽  
Yong Tae Yoon ◽  
Mark B. Glick ◽  
...  
Keyword(s):  
Power Plant ◽  
Flow Control ◽  
Control Method ◽  
Virtual Power ◽  
Virtual Power Plant

scholarly journals A Critical Review of Supersonic Flow Control for High-Speed Applications

2021 ◽  
Vol 11 (15) ◽  
pp. 6899
Author(s):  
Abdul Aabid ◽  
Sher Afghan Khan ◽  
Muneer Baig
Keyword(s):  
Supersonic Flow ◽  
Flow Control ◽  
Active Control ◽  
Critical Review ◽  
High Speed ◽  
Passive Control ◽  
Control Method ◽  
Sudden Expansion ◽  
Control Approach ◽  
Cost Efficient

In high-speed fluid dynamics, base pressure controls find many engineering applications, such as in the automobile and defense industries. Several studies have been reported on flow control with sudden expansion duct. Passive control was found to be more beneficial in the last four decades and is used in devices such as cavities, ribs, aerospikes, etc., but these need additional control mechanics and objects to control the flow. Therefore, in the last two decades, the active control method has been used via a microjet controller at the base region of the suddenly expanded duct of the convergent–divergent (CD) nozzle to control the flow, which was found to be a cost-efficient and energy-saving method. Hence, in this paper, a systemic literature review is conducted to investigate the research gap by reviewing the exhaustive work on the active control of high-speed aerodynamic flows from the nozzle as the major focus. Additionally, a basic idea about the nozzle and its configuration is discussed, and the passive control method for the control of flow, jet and noise are represented in order to investigate the existing contributions in supersonic speed applications. A critical review of the last two decades considering the challenges and limitations in this field is expressed. As a contribution, some major and minor gaps are introduced, and we plot the research trends in this field. As a result, this review can serve as guidance and an opportunity for scholars who want to use an active control approach via microjets for supersonic flow problems.

scholarly journals A Two-Stage Quality Control Method for 2-m Temperature Observations Using Biweight Means and a Progressive EOF Analysis

2013 ◽  
Vol 141 (2) ◽  
pp. 798-808 ◽  
Author(s):  
Zhifang Xu ◽  
Yi Wang ◽  
Guangzhou Fan
Keyword(s):  
Quality Control ◽  
Control Method ◽  
Control Process ◽  
Lapse Rate ◽  
Systematic Bias ◽  
Eof Analysis ◽  
Two Stage ◽  
Quality Control Method ◽  
Quality Control Process ◽  
The Difference

Abstract The relatively smooth terrain embedded in the numerical model creates an elevation difference against the actual terrain, which in turn makes the quality control of 2-m temperature difficult when forecast or analysis fields are utilized in the process. In this paper, a two-stage quality control method is proposed to address the quality control of 2-m temperature, using biweight means and a progressive EOF analysis. The study is made to improve the quality control of the observed 2-m temperature collected by China and its neighboring areas, based on the 6-h T639 analysis from December 2009 to February 2010. Results show that the proposed two-stage quality control method can secure the needed quality control better, compared with a regular EOF quality control process. The new method is, in particular, able to remove the data that are dotted with consecutive errors but showing small fluctuations. Meanwhile, compared with the lapse rate of temperature method, the biweight mean method is able to remove the systematic bias generated by the model. It turns out that such methods make the distributions of observation increments (the difference between observation and background) more Gaussian-like, which ensures the data quality after the quality control.

Mechanism and Flow Control on the Mismatching of Impeller and Vaned Diffuser Caused by Inlet Prewhirl for Centrifugal Compressors

2016 ◽  
Author(s):  
Qiangqiang Huang ◽  
Xinqian Zheng ◽  
Aolin Wang
Keyword(s):  
Flow Control ◽  
Control Method ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Vaned Diffuser ◽  
Inlet Distortion ◽  
Computational Fluid Dynamics Cfd ◽  
Stagger Angle ◽  
Good Agreement ◽  
Matching Relation

Air often flows into compressors with inlet prewhirl, because it will obtain a circumferential component of velocity via inlet distortion or swirl generators such as inlet guide vanes. A lot of research has shown that inlet prewhirl does influence the characteristics of components, but the change of the matching relation between the components caused by inlet prewhirl is still unclear. This paper investigates the influence of inlet prewhirl on the matching of the impeller and the diffuser and proposes a flow control method to cure mismatching. The approach combines steady three-dimensional Reynolds-averaged Navier-Stokes (RANS) simulations with theoretical analysis and modeling. The result shows that a compressor whose impeller and diffuser match well at zero prewhirl will go to mismatching at non-zero prewhirl. The diffuser throat gets too large to match the impeller at positive prewhirl and gets too small for matching at negative prewhirl. The choking mass flow of the impeller is more sensitive to inlet prewhirl than that of the diffuser, which is the main reason for the mismatching. To cure the mismatching via adjusting the diffuser vanes stagger angle, a one-dimensional method based on incidence matching has been proposed to yield a control schedule for adjusting the diffuser. The optimal stagger angle predicted by analytical method has good agreement with that predicted by computational fluid dynamics (CFD). The compressor is able to operate efficiently in a much broader flow range with the control schedule. The flow range, where the efficiency is above 80%, of the datum compressor and the compressor only employing inlet prewhirl and no control are just 25.3% and 31.8%, respectively. For the compressor following the control schedule, the flow range is improved up to 46.5%. This paper also provides the perspective of components matching to think about inlet distortion.

Dual-position excitation technique in flow control over an airfoil at low speeds

2018 ◽  
Vol 30 (9) ◽  
pp. 4141-4154
Author(s):  
Abbas Ebrahimi ◽  
Majid Hajipour ◽  
Kamran Ghamkhar
Keyword(s):  
Flow Control ◽  
Shear Layer ◽  
Control Method ◽  
Lift Coefficient ◽  
Shear Layers ◽  
Control Flow ◽  
Plasma Actuators ◽  
Dbd Plasma ◽  
Surface Shear ◽  
Content Type

PurposeThe purpose of this paper is to control flow separation over a NACA 4415 airfoil by applying unsteady forces to the separated shear layers using dielectric barrier discharge (DBD) plasma actuators. This novel flow control method is studied under conditions which the airfoil angle of attack is 18°, and Reynolds number based on chord length is 5.5 × 105.Design/methodology/approachLarge eddy simulation of the turbulent flow is used to capture vortical structures through the airfoil wake. Power spectral density analysis of the baseline flow indicates dominant natural frequencies associated with “shear layer mode” and “wake mode.” The wake mode frequency is used simultaneously to excite separated shear layers at both the upper surface and the trailing edge of the airfoil (dual-position excitation), and it is also used singly to excite the upper surface shear layer (single-position excitation).FindingsBased on the results, actuations manipulate the shear layers instabilities and change the wake patterns considerably. It is revealed that in the single-position excitation case, the vortices shed from the upper surface shear layer are more coherent than the dual-position excitation case. The maximum value of lift coefficient and lift-to-drag ratio is achieved, respectively, by single-position excitation as well as dual-position excitation.Originality/valueThe paper contributes to the understanding and progress of DBD plasma actuators for flow control applications. Further, this research could be a beneficial solution for the promising design of advanced low speed flying vehicles.

Effect of Blade Aspiration Slot Configuration on the Aerodynamic Performance of a Highly Loaded Aspirated Compressor Cascade

2017 ◽  
Author(s):  
Longxin Zhang ◽  
Le Cai ◽  
Bao Liu ◽  
Jun Ding ◽  
Songtao Wang
Keyword(s):  
Flow Control ◽  
Flow Rate ◽  
Control Method ◽  
Active Flow Control ◽  
Experimental Studies ◽  
Aerodynamic Performance ◽  
Flow Path ◽  
Compressor Cascade ◽  
Flow Loss ◽  
Highly Loaded

As a promising active flow control method, boundary layer suction (BLS) can be used to enhance the aerodynamic performance of the highly-loaded compressor effectively, and due to this reason, extensive studies have been carried out on it. However, contrast to those abundant studies focusing on the flow control effects of BLS, little attention has been paid on the design method of the aspiration flow path. This work presents a 3-D steady numerical simulation on a highly-loaded aspirated compressor cascade. The aspiration slot is implemented at its best location based on the previous experimental studies and the aspiration flow rate is fix to 1.5% of the inlet massflow. The plenum configuration follows the blade shape and remains unchanged. One-side-aspiration manner is adopted to simplify the aspiration devices. Two critical geometry parameters, slot angle and slot width, are varied to study the effects of blade aspiration slot configuration on the cascade loss, radial distribution of the aspiration flow rate and inner flow structures within the aspiration flow path. Results show that the slot configuration does affect the cascade performance. In comparison with the throughflow performance, it is especially true once the flow loss caused by the aspiration flow path is also taken into account, and higher flow loss will be generated within the aspiration flow path if an inappropriate scheme is adopted. In the present investigation, apart from the cases with larger negative slot angle, a wider slot is more preferable to a narrower one, since it could enhance the aspiration capacity near the endwall regions and lower the dissipation loss within the aspiration flow path. In terms of the slot angle, a larger negative value, i.e., the slot direction more aligned with the incoming flow, is not beneficial to improve the throughflow performance, while concerning the flow loss yield by the aspiration flow path, a proper negative slot angle is always optimal.

Sign in / Sign up

Export Citation Format

Share Document