Effects of short‐term variations in near‐surface moisture content on shallow seismic data

1995 ◽  
Author(s):  
Robert D. Jefferson ◽  
Don W. Steeples
Geophysics ◽  
1998 ◽  
Vol 63 (4) ◽  
pp. 1357-1362 ◽  
Author(s):  
Robert D. Jefferson ◽  
Don W. Steeples ◽  
Ross A. Black ◽  
Tim Carr

Repeated shallow‐seismic experiments were conducted at a site on days with different near‐surface moisture conditions in unconsolidated material. Experimental field parameters remained constant to ensure comparability of results. Variations in the seismic data are attributed to the changes in soil‐moisture content of the unconsolidated material. Higher amplitudes of reflections and refractions were obtained under wetter near‐surface conditions. An increase in amplitude of 21 dB in the 100–300 Hz frequency range was observed when the moisture content increased from 18% to 36% in the upper 0.15 m (0.5 ft) of the subsurface. In the time‐domain records, highly saturated soil conditions caused large‐amplitude ringy wavelets that interfered with and degraded the appearance of some of the reflection information in the raw field data. This may indicate that an intermediate near‐surface moisture content is most conducive to the recording of high‐quality shallow‐seismic reflection data at this site. This study illustrates the drastic changes that can occur in shallow‐seismic data due to variations in near‐surface moisture conditions. These conditions may need to be considered to optimize the acquisition timing and parameters prior to collection of data.


Author(s):  
David G. Jones ◽  
Christopher H. Vane ◽  
Solveigh Lass-Evans ◽  
Simon Chenery ◽  
Bob Lister ◽  
...  

ABSTRACTGeochemical and related studies have been made of near-surface sediments from the River Clyde estuary and adjoining areas, extending from Glasgow to the N, and W as far as the Holy Loch on the W coast of Scotland, UK. Multibeam echosounder, sidescan sonar and shallow seismic data, taken with core information, indicate that a shallow layer of modern sediment, often less than a metre thick, rests on earlier glacial and post-glacial sediments. The offshore Quaternary history can be aligned with onshore sequences, with the recognition of buried drumlins, settlement of muds from quieter water, probably behind an ice dam, and later tidal delta deposits. The geochemistry of contaminants within the cores also indicates shallow contaminated sediments, often resting on pristine pre-industrial deposits at depths less than 1m. The distribution of different contaminants with depth in the sediment, such as Pb (and Pb isotopes), organics and radionuclides, allow chronologies of contamination from different sources to be suggested. Dating was also attempted using microfossils, radiocarbon and 210Pb, but with limited success. Some of the spatial distribution of contaminants in the surface sediments can be related to grain-size variations. Contaminants are highest, both in absolute terms and in enrichment relative to the natural background, in the urban and inner estuary and in the Holy Loch, reflecting the concentration of industrial activity.


1995 ◽  
Author(s):  
Johan O. A. Robertsson ◽  
Andre' Pugin ◽  
Klaus Holliger ◽  
Alan G. Green

2014 ◽  
Vol 152 ◽  
pp. 536-546 ◽  
Author(s):  
Karl M. Meingast ◽  
Michael J. Falkowski ◽  
Evan S. Kane ◽  
Lynette R. Potvin ◽  
Brian W. Benscoter ◽  
...  

Author(s):  
Rami Benkreif ◽  
Fatima Zohra Brahmia ◽  
Csilla Csiha

AbstractSurface tension of solid wood surfaces affects the wettability and thus the adhesion of various adhesives and wood coatings. By measuring the contact angle of the wood, the surface tension can be calculated based on the Young-Dupré equation. Several publications have reported on contact angle measured with different test liquids, under different conditions. Results can only be compared if the test conditions are similar. While the roles of the drop volume, image shooting time etc., are widely recognized, the role of the wood surface moisture content (MC) is not evaluated in detail. In this study, the effect of wood moisture content on contact angle values, measured with distilled water and diiodomethane, on sanded birch (Betula pendula) surfaces was investigated, in order to find the relationship between them. With increasing MC from approximately 6% to 30%, increasing contact angle (decreasing surface tension) values were measured according to a logarithmic function. The function makes possible the calculation of contact angles that correspond to different MCs.


Geophysics ◽  
2006 ◽  
Vol 71 (5) ◽  
pp. U67-U76 ◽  
Author(s):  
Robert J. Ferguson

The possibility of improving regularization/datuming of seismic data is investigated by treating wavefield extrapolation as an inversion problem. Weighted, damped least squares is then used to produce the regularized/datumed wavefield. Regularization/datuming is extremely costly because of computing the Hessian, so an efficient approximation is introduced. Approximation is achieved by computing a limited number of diagonals in the operators involved. Real and synthetic data examples demonstrate the utility of this approach. For synthetic data, regularization/datuming is demonstrated for large extrapolation distances using a highly irregular recording array. Without approximation, regularization/datuming returns a regularized wavefield with reduced operator artifacts when compared to a nonregularizing method such as generalized phase shift plus interpolation (PSPI). Approximate regularization/datuming returns a regularized wavefield for approximately two orders of magnitude less in cost; but it is dip limited, though in a controllable way, compared to the full method. The Foothills structural data set, a freely available data set from the Rocky Mountains of Canada, demonstrates application to real data. The data have highly irregular sampling along the shot coordinate, and they suffer from significant near-surface effects. Approximate regularization/datuming returns common receiver data that are superior in appearance compared to conventional datuming.


1998 ◽  
Vol 37 (3) ◽  
pp. 308-324 ◽  
Author(s):  
Stephen P. Palm ◽  
Denise Hagan ◽  
Geary Schwemmer ◽  
S. H. Melfi

Abstract A new technique for retrieving near-surface moisture and profiles of mixing ratio and potential temperature through the depth of the marine atmospheric boundary layer (MABL) using airborne lidar and multichannel infrared radiometer data is presented. Data gathered during an extended field campaign over the Atlantic Ocean in support of the Lidar In-space Technology Experiment are used to generate 16 moisture and temperature retrievals that are then compared with dropsonde measurements. The technique utilizes lidar-derived statistics on the height of cumulus clouds that frequently cap the MABL to estimate the lifting condensation level. Combining this information with radiometer-derived sea surface temperature measurements, an estimate of the near-surface moisture can be obtained to an accuracy of about 0.8 g kg−1. Lidar-derived statistics on convective plume height and coverage within the MABL are then used to infer the profiles of potential temperature and moisture with a vertical resolution of 20 m. The rms accuracy of derived MABL average moisture and potential temperature is better than 1 g kg−1 and 1°C, respectively. The method relies on the presence of a cumulus-capped MABL, and it was found that the conditions necessary for use of the technique occurred roughly 75% of the time. The synergy of simple aerosol backscatter lidar and infrared radiometer data also shows promise for the retrieval of MABL moisture and temperature from space.


Sign in / Sign up

Export Citation Format

Share Document