Lithology-controlled stress variations and pad-scale faults: A case study of hydraulic fracturing in the Woodford Shale, Oklahoma

Geophysics ◽  
2017 ◽  
Vol 82 (6) ◽  
pp. ID35-ID44 ◽  
Author(s):  
Xiaodong Ma ◽  
Mark D. Zoback
Keyword(s):  
Hydraulic Fracturing ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
Strike Slip ◽  
Woodford Shale ◽  
Stress Regime ◽  
Component Content ◽  
Microseismic Events ◽  
Minimum Horizontal Stress ◽  
Stress Variations

We have conducted an integrated study to investigate the petrophysical and geomechanical factors controlling the effectiveness of hydraulic fracturing (HF) in four subparallel horizontal wells in the Mississippi Limestone-Woodford Shale (MSSP-WDFD) play in Oklahoma. In two MSSP wells, the minimum horizontal stress [Formula: see text] indicated by the instantaneous shut-in pressures of the HF stages are significantly less than the vertical stress [Formula: see text]. This, combined with observations of drilling-induced tensile fractures in the MSSP in a vertical well at the site, indicates that this formation is in a normal/strike-slip faulting stress regime, consistent with earthquake focal mechanisms and other stress indicators in the area. However, the [Formula: see text] values are systematically higher and vary significantly from stage to stage in two WDFD wells. The stages associated with the abnormally high [Formula: see text] values (close to [Formula: see text]) were associated with little to no proppant placement and a limited number of microseismic events. We used compositional logs to determine the content of compliant components (clay and kerogen). Due to small variations in the trajectories of the horizontal wells, they penetrated three thin, but compositionally distinct WDFD lithofacies. We found that [Formula: see text] along the WDFD horizontals increases when the stage occurred in a zone with high clay and kerogen content. These variations of [Formula: see text] can be explained by various degrees of viscous stress relaxation, which results in the increase in [Formula: see text] (less stress anisotropy), as the compliant component content increases. The distribution of microseismic events was also affected by normal and strike-slip faults cutting across the wells. The locations of these faults were consistent with unusual lineations of microseismic events and were confirmed by 3D seismic data. Thus, the overall effectiveness of HF stimulation in the WDFD wells at this site was strongly affected the abnormally high HF gradients in clay-rich lithofacies and the presence of preexisting, pad-scale faults.

Predicting Lithology-Controlled Stress Variations in the Woodford Shale from Well Log Data via Viscoplastic Relaxation

SPE Journal ◽  
2020 ◽  
Vol 25 (05) ◽  
pp. 2534-2546 ◽  
Author(s):  
Xiaodong Ma ◽  
Mark D. Zoback
Keyword(s):  
Horizontal Wells ◽  
Horizontal Stress ◽  
Constitutive Relationship ◽  
Woodford Shale ◽  
North Central ◽  
Multistage Hydraulic Fracturing ◽  
Well Trajectory ◽  
Minimum Horizontal Stress ◽  
Stress Variations ◽  
Good Agreement

Summary We report here a study of lithology-controlled stress variations observed in the Woodford shale (WDFD) in north-central Oklahoma. In a previous study, we showed that the magnitude of the minimum horizontal stress Shmin systematically varied with the abundance of clay plus kerogen in three distinct WDFD lithofacies. In this study, we demonstrate that it is possible to quantitatively estimate the observed stress variations using elastic properties determined from well logs as proxies for laboratory-inferred parameters via a relatively simple viscoplastic constitutive relationship. The modeled variations of Shmin along the two horizontal wells that encounter the three lithofacies along their respective well trajectory are in good agreement with measured values obtained from multistage hydraulic fracturing (HF). We believe that the application of the workflow described here in the context of viscoplastic stress relaxation can facilitate the understanding of layer-to-layer stress variations with lithology and thus contribute to improved HF effectiveness.

Real-Time Wellbore Stability and Hole Quality Evaluation Using LWD Azimuthal Photoelectric Measurements

2021 ◽  
Author(s):  
Khaqan Khan ◽  
Mohammad Altwaijri ◽  
Ahmed Taher ◽  
Mohamed Fouda ◽  
Mohamed Hussein
Keyword(s):  
Real Time ◽  
Drilling Fluid ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
Wellbore Stability ◽  
Fluid Density ◽  
Stress Regime ◽  
Borehole Breakout ◽  
Photoelectric Measurements ◽  
Minimum Horizontal Stress

Abstract Horizontal and high-inclination deep wells are routinely drilled to enhance hydrocarbon recovery. To sustain production rates, these wells are generally designed to be drilled in the direction of minimum horizontal stress in strike slip stress regime to facilitate transverse fracture growth during fracturing operations. These wells can also cause wellbore instability challenges due to high stress concentration due to compressional or strike-slip stress regimes. Hence, apart from pre-drill wellbore stability analysis for an optimum mud weight design, it is important to continuously monitor wellbore instability indicators during drilling. With the advancements of logging-while-drilling (LWD) techniques, it is now possible to better assess wellbore stability during drilling and, if required, to take timely decisions and adjust mud weight to help mitigate drilling problems. The workflow for safely drilling deep horizontal wells starts with analyzing the subsurface stress regime using data from offset wells. Through a series of steps, data is integrated to develop a geomechanics model to select an optimum drilling-fluid density to maintain wellbore stability while minimizing the risks of differential sticking and mud losses. Due to potential lateral subsurface heterogeneity, continuous monitoring of drilling events and LWD measurements is required, to update and calibrate the pre-well model. LWD measurements have long been used primarily for petrophysical analysis and well placement in real time. The use of azimuthal measurements for real-time wellbore stability evaluation applications is a more recent innovation. Shallow formation density readings using azimuthal LWD measurements provide a 360° coverage of wellbore geometry, which can be effectively used to identify magnitude and orientation of borehole breakout at the wellbore wall. Conventional LWD tools also provide auxiliary azimuthal measurements, such as photoelectric (Pe) measurement, derived from the near detector of typical LWD density sensors. The Pe measurement, with a very shallow depth of investigation (DOI), is more sensitive to small changes in borehole shape compared with other measurements from the same sensor, particularly where a high contrast exists between drilling mud and formation Pe values. Having azimuthal measurements of both Pe and formation density while drilling facilitates better control on assess wellbore stability assessment in real time and make decisions on changes in mud density or drilling parameters to keep wellbore stable and avoid drilling problems. Time dependency of borehole breakout can also be evaluated using time-lapse data to enhance analysis and reduce uncertainty. Analyzing LWD density and Pe azimuthal data in real time has guided real-time decisions to optimize drilling fluid density while drilling. The fluid density indicated by the initial geo-mechanical analysis has been significantly adjusted, enabling safe drilling of deep horizontal wells by minimizing wellbore breakouts. Breakouts identified by LWD density and photoelectric measurements has been further verified using wireline six-arm caliper logs after drilling. Contrary to routinely used density image, this paper presents use of Pe image for evaluating wellbore stability and quality in real time, thereby improving drilling safety and completion of deep horizontal wells drilled in the minimum horizontal stress direction.

scholarly journals Rupture Directivity in 3D Inferred From Acoustic Emissions Events in a Mine-Scale Hydraulic Fracturing Experiment

2021 ◽  
Vol 9 ◽  
Author(s):  
José Ángel López-Comino ◽  
Simone Cesca ◽  
Peter Niemz ◽  
Torsten Dahm ◽  
Arno Zang
Keyword(s):  
Hydraulic Fracturing ◽  
Acoustic Emissions ◽  
Local Stress ◽  
Horizontal Stress ◽  
Monitoring Networks ◽  
Rupture Directivity ◽  
Shallow Subsurface ◽  
Minimum Horizontal Stress ◽  
Directivity Effects ◽  
Full Waveforms

Rupture directivity, implying a predominant earthquake rupture propagation direction, is typically inferred upon the identification of 2D azimuthal patterns of seismic observations for weak to large earthquakes using surface-monitoring networks. However, the recent increase of 3D monitoring networks deployed in the shallow subsurface and underground laboratories toward the monitoring of microseismicity allows to extend the directivity analysis to 3D modeling, beyond the usual range of magnitudes. The high-quality full waveforms recorded for the largest, decimeter-scale acoustic emission (AE) events during a meter-scale hydraulic fracturing experiment in granites at ∼410 m depth allow us to resolve the apparent durations observed at each AE sensor to analyze 3D-directivity effects. Unilateral and (asymmetric) bilateral ruptures are then characterized by the introduction of a parameter κ, representing the angle between the directivity vector and the station vector. While the cloud of AE activity indicates the planes of the hydrofractures, the resolved directivity vectors show off-plane orientations, indicating that rupture planes of microfractures on a scale of centimeters have different geometries. Our results reveal a general alignment of the rupture directivity with the orientation of the minimum horizontal stress, implying that not only the slip direction but also the fracture growth produced by the fluid injections is controlled by the local stress conditions.

Geomechanical Approach in Classification of Borehole Failures in Fractured Carbonates of Boca De Jaruco Field

2021 ◽  
Author(s):  
Anna Vladimirovna Norkina ◽  
Iaroslav Olegovich Simakov ◽  
Yuriy Anatoljevich Petrakov ◽  
Alexey Evgenjevich Sobolev ◽  
Oleg Vladimirovich Petrashov ◽  
...  
Keyword(s):  
Stress State ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
In Situ Stress ◽  
Vertical Wells ◽  
Stress Regime ◽  
Geophysical Information ◽  
The Republic ◽  
Maximum Horizontal Stress

Abstract This article is a continuation of the work on geomechanically calculations for optimizing the drilling of horizontal wells into the productive reservoir M at the Boca de Haruco field of the Republic of Cuba, presented in the article SPE-196897. As part of the work, an assessment of the stress state and direction was carried out using geological and geophysical information, an analysis of the pressure behavior during steam injections, cross-dipole acoustics, as well as oriented caliper data in vertical wells. After the completion of the first part of the work, the first horizontal wells were successfully drilled into the M formation. According to the recommendations, additional studies were carried out: core sampling and recording of micro-imager logging in the deviated sections. Presence of wellbore failures at the inclined sections allowed to use the method of inverse in-situ stress modeling based on image logs interpretation. The classification of wellbore failures by micro-imager logging: natural origin and violations of technogenic genesis is carried out. The type of breakout is defined. The result of the work was the determination of the stress state and horizontal stresses direction. In addition, the article is supplemented with the calculation of the maximum horizontal stress through the stress regime identifier factor.

PRESENT-DAY STATE-OF-STRESS OF SOUTHEAST AUSTRALIA

2006 ◽  
Vol 46 (1) ◽  
pp. 283 ◽  
Author(s):  
E. Nelson ◽  
R. Hillis ◽  
M. Sandiford ◽  
S. Reynolds ◽  
S. Mildren
Keyword(s):  
Focal Mechanism ◽  
Horizontal Stress ◽  
Strike Slip ◽  
Focal Mechanism Solutions ◽  
Southeast Australia ◽  
State Of Stress ◽  
Earthquake Focal Mechanism ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress ◽  
Gippsland Basin

There have been several studies, both published and unpublished, of the present-day state-of-stress of southeast Australia that address a variety of geomechanical issues related to the petroleum industry. This paper combines present-day stress data from those studies with new data to provide an overview of the present-day state-of-stress from the Otway Basin to the Gippsland Basin. This overview provides valuable baseline data for further geomechanical studies in southeast Australia and helps explain the regional controls on the state-of-stress in the area.Analysis of existing and new data from petroleum wells reveals broadly northwest–southeast oriented, maximum horizontal stress with an anticlockwise rotation of about 15° from the Otway Basin to the Gippsland Basin. A general increase in minimum horizontal stress magnitude from the Otway Basin towards the Gippsland Basin is also observed. The present-day state-of-stress has been interpreted as strike-slip in the South Australian (SA) Otway Basin, strike-slip trending towards reverse in the Victorian Otway Basin and borderline strike-slip/reverse in the Gippsland Basin. The present-day stress states and the orientation of the maximum horizontal stress are consistent with previously published earthquake focal mechanism solutions and the neotectonic record for the region. The consistency between measured present-day stress in the basement (from focal mechanism solutions) and the sedimentary basin cover (from petroleum well data) suggests a dominantly tectonic far-field control on the present-day stress distribution of southeast Australia. The rotation of the maximum horizontal stress and the increase in magnitude of the minimum horizontal stress from west to east across southeast Australia may be due to the relative proximity of the New Zealand segment of the plate boundary.

scholarly journals Geomechanical Analysis to Avoid Serious Drilling Hazards in Zubair Oilfield, Southern Iraq

2020 ◽  
pp. 1994-2003
Author(s):  
Shaban Dharb Shaban ◽  
Hassan Abdul Hadi
Keyword(s):  
Gamma Ray ◽  
Mechanical Test ◽  
Horizontal Wells ◽  
Failure Criteria ◽  
Horizontal Stress ◽  
Wellbore Instability ◽  
Geomechanical Analysis ◽  
Safe Mud Window ◽  
Rock Mechanical Properties ◽  
Minimum Horizontal Stress

Zubair oilfield is an efficient contributor to the total Iraqi produced hydrocarbon. Drilling vertical wells as well as deviated and horizontal wells have been experiencing intractable challenges. Investigation of well data showed that the wellbore instability issues were the major challenges to drill in Zubair oilfield. These experienced borehole instability problems are attributed to the increase in the nonproductive time (NPT). This study can assist in managing an investment-drilling plan with less nonproductive time and more efficient well designing.       To achieve the study objectives, a one dimension geomechanical model (1D MEM) was constructed based on open hole log measurements, including Gamma-ray (GR), Caliper (CALI), Density (RHOZ), sonic compression (DTCO) and shear (DTSM) wave velocities , and Micro imager log (FMI). The determined 1D MEM components, i.e., pore pressure, rock mechanical properties, in-situ principal stress magnitudes and orientations, were calibrated using the data acquired from repeated formation test (RFT), hydraulic fracturing test (Mini-frac), and laboratory rock core mechanical test (triaxial test). Then, a validation model coupled with three failure criteria, i.e., Mohr-Coulomb, Mogi-Coulomb, and Modified lade, was conducted using the Caliper and Micro-imager logs. Finally, sensitivity and forecasting stability analyses were implemented to predict the most stable wellbore trajectory concerning the safe mud window for the planned wells.    The implemented wellbore instability analysis utilizing Mogi-Coulomb criterion demonstrated that the azimuth of 140o paralleling to the minimum horizontal stress is preferable to orient deviated and horizontal wells. The vertical and slightly deviated boreholes (1ess than 30o) are the most stable wellbores, and they are recommended to be drilled with 11.6 -12 ppg mud weight. The highly deviated and horizontal wells are recommended to be drilled with a mud weight of 12-12.6 ppg.

scholarly journals In Situ Stress and Stress Regime in the Onshore Part of the Northeast Java Basin

2021 ◽  
Vol 44 (2) ◽  
pp. 95-105
Author(s):  
Agus M. Ramdhan
Keyword(s):  
Petroleum Industry ◽  
Horizontal Stress ◽  
In Situ Stress ◽  
Vertical Stress ◽  
Stress Regime ◽  
Severe Erosion ◽  
Tectonically Active ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress

In situ stress is importance in the petroleum industry because it will significantly enhance our understanding of present-day deformation in a sedimentary basin. The Northeast Java Basin is an example of a tectonically active basin in Indonesia. However, the in situ stress in this basin is still little known. This study attempts to analyze the regional in situ stress (i.e., vertical stress, minimum and maximum horizontal stresses) magnitude and orientation, and stress regime in the onshore part of the Northeast Java Basin based on twelve wells data, consist of density log, direct/indirect pressure test, and leak-off test (LOT) data. The magnitude of vertical (  and minimum horizontal (  stresses were determined using density log and LOT data, respectively. Meanwhile, the orientation of maximum horizontal stress  (  was determined using image log data, while its magnitude was determined based on pore pressure, mudweight, and the vertical and minimum horizontal stresses. The stress regime was simply analyzed based on the magnitude of in situ stress using Anderson’s faulting theory. The results show that the vertical stress ( ) in wells that experienced less erosion can be determined using the following equation: , where  is in psi, and z is in ft. However, wells that experienced severe erosion have vertical stress gradients higher than one psi/ft ( . The minimum horizontal stress ( ) in the hydrostatic zone can be estimated as, while in the overpressured zone, . The maximum horizontal stress ( ) in the shallow and deep hydrostatic zones can be estimated using equations: and , respectively. While in the overpressured zone, . The orientation of  is ~NE-SW, with a strike-slip faulting stress regime.

THE OTWAY BASIN: EARLY CRETACEOUS RIFTING TO NEOGENE INVERSION

1995 ◽  
Vol 35 (1) ◽  
pp. 494 ◽  
Author(s):  
A.J. Buffin ◽  
A.J. Sutherland ◽  
J.A. Gorski
Keyword(s):  
Stress Field ◽  
Normal Fault ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
Natural Fracture ◽  
Water Flooding ◽  
Hydraulic Fractures ◽  
Vertical Wells ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress

Borehole breakouts and hydraulic fractures in­ferred from dipmeter and formation microscanner logs indicate that the minimum horizontal stress (σh) is oriented 035°N in the South Australian sector of the Otway Basin. Density and sonic check-shot log data indicate that vertical stress (σv) increases from approximately 20 MPa at a depth of one km to 44 MPa at two km and 68 MPa at three km. Assum­ing a normal fault condition (i.e. σy > σH > σh), the magnitude of σh is 75 per cent of the magnitude of the maximum horizontal stress (σH), and the magni­tude of σH is close to that of av. Sonic velocity compaction trends for shales suggest that pore pressure is generally near hydrostatic in the Otway Basin.Knowledge of the contemporary stress field has a number of implications for hydrocarbon produc­tion and exploration in the basin. Wellbore quality in vertical wells may be improved (breakouts sup­pressed) by increasing the mud weight to a level below that which induces hydraulic fracture, or other drilling problems related to excessive mud weight. Horizontal wells drilled in the σh direction (035°N/215°N) should be more stable than those drilled in the σH direction, and indeed than vertical wells. In any EOR operations where water flooding promotes hydraulic fracturing, injectors should be aligned in the aH (125°N/305°N) direction, and off­set from producers in the orthogonal σh direction. Any deviated/horizontal wells targeting the frac­tured basement play should be oriented in the σh (035°N/215°N) direction to maximise intersection with this open, natural fracture trend. Hydrocar­bon recovery in wells deviated towards 035°N/215°N may also be enhanced by inducing multiple hydrau­lic fractures along the wellbore.Considering exploration-related issues, faults following the dominant structural trend, sub-paral­lel to σH orientation, are the most prone to be non-sealing during any episodic build-up of pore pres­sure. Pre-existing vertical faults striking 080-095°N and 155-170°N are the most prone to at least a component of strike-slip reactivation within the contemporary stress field.

Valuation of hydraulic fracturing potentials of organic-rich shales from the Anambra basin using rock mechanical properties from wireline logs

2021 ◽  
Vol 19 (3) ◽  
pp. 45-44
Author(s):  
Homa Viola Akaha-Tse ◽  
Michael Oti ◽  
Selegha Abrakasa ◽  
Charles Ugwu Ugwueze
Keyword(s):  
Mechanical Properties ◽  
Hydraulic Fracturing ◽  
Horizontal Stress ◽  
Shale Formations ◽  
In Situ Stresses ◽  
Anambra Basin ◽  
Wireline Logs ◽  
Rock Mechanical Properties ◽  
Minimum Horizontal Stress

This study was carried out to determine the rock mechanical properties relevant for hydrocarbon exploration and production by hydraulic  fracturing of organic rich shale formations in Anambra basin. Shale samples and wireline logs were analysed to determine the petrophysical, elastic, strength and in-situ properties necessary for the design of a hydraulic fracturing programme for the exploitation of the shales. The results obtained indicated shale failure in shear and barreling under triaxial test conditions. The average effective porosity of 0.06 and permeability of the order of 10-1 to 101 millidarcies showed the imperative for induced fracturing to assure fluid flow. Average Young’s modulus and Poisson’s ratio of about 2.06 and 0.20 respectively imply that the rocks are favourable for the formation and propagation of fractures during hydraulic fracking. The minimum horizontal stress, which determines the direction of formation and growth of artificially induced hydraulic fractures varies from wellto-well, averaging between 6802.62 to 32790.58 psi. The order of variation of the in-situ stresses is maximum horizontal stress>vertical stress>minimum horizontal stress which implies a reverse fault fracture regime. The study predicts that the sweet spots for the exploration and development of the shale-gas are those sections of the shale formations that exhibit high Young’s modulus, low Poisson’s ratio, and high brittleness. The in-situ stresses required for artificially induced fractures which provide pore space for shale gas accumulation and expulsion are adequate. The shales possess suitable mechanical properties to fracture during hydraulic fracturing. Application of these results will enhance the potentials of the onshore Anambra basin as a reliable component in increasing Nigeria’s gas reserves, for the improvement of the nation’s economy and energy security. Key Words: Hydraulic Fracturing, Organic-rich Shales, Rock Mechanical Properties, Petrophysical Properties, Anambra Basin

Design of Horizontal Wellbore in Dadas Shales of Turkey by Considering Wellbore Stability and Reservoir Geomechanics

2021 ◽  
Author(s):  
Sukru Merey ◽  
Can Polat ◽  
Tuna Eren
Keyword(s):  
Hydraulic Fracturing ◽  
Horizontal Well ◽  
Oil And Gas ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
Wellbore Stability ◽  
Horizontal Drilling ◽  
Horizontal Wellbore ◽  
Reservoir Geomechanics ◽  
Maximum Horizontal Stress

Abstract Currently, many horizontal wells are being drilled in Dadas shales of Turkey. Dadas shales have both oil (mostly) and gas potentials. Thus, hydraulic fracturing operations are being held to mobilize hydrocarbons. Up to 1000 m length horizontal wells are drilled for this purpose. However, there is not any study analyzing wellbore stability and reservoir geomechanics in the conditions of Dadas shales. In this study, the directions of horizontal wells, wellbore stability and reservoir geomechanics of Dadas shales were designed by using well log data. In this study, the python code developed by using Kirsch equations was developed. With this python code, it is possible to estimate unconfined compressive strength in along wellbore at different deviations. By analyzing caliper log, density and porosity logs of Dadas shales, vertical stress of Dadas shales was estimated and stress polygon for these shale was prepared in this study. Then, optimum direction of horizontal well was suggested to avoid any wellbore stability problems. According to the results of this study, high stresses are seen in horizontal directions. In this study, it was found that the maximum horizontal stress in almost the direction of North-South. The results of this study revealed that direction of maximum horizontal stress and horizontal well direction fluid affect the wellbore stability significantly. Thus, in this study, better horizontal well design was made for Dadas shales. Currently, Dadas shales are popular in Turkey because of its oil and gas potential so horizontal drilling and hydraulic fracturing operations are being held. However, in literature, there is no study about horizontal wellbore designs for Dadas shales. This study will be novel and provide information about the horizontal drilling design of Dadas shales.

Sign in / Sign up

Export Citation Format

Share Document