Predicting the azimuth of natural fractures and in-situ horizontal stress: A case study from Sichuan Basin, China

Geophysics ◽  
2021 ◽  
pp. 1-97
Author(s):  
kai lin ◽  
Bo Zhang ◽  
Jianjun Zhang ◽  
Huijing Fang ◽  
Kefeng Xi ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Seismic Data ◽  
Sichuan Basin ◽  
Horizontal Stress ◽  
Seismic Attributes ◽  
Seismic Events ◽  
Natural Fractures ◽  
Microseismic Data ◽  
Maximum Horizontal Stress

The azimuth of fractures and in-situ horizontal stress are important factors in planning horizontal wells and hydraulic fracturing for unconventional resources plays. The azimuth of natural fractures can be directly obtained by analyzing image logs. The azimuth of the maximum horizontal stress σH can be predicted by analyzing the induced fractures on image logs. The clustering of micro-seismic events can also be used to predict the azimuth of in-situ maximum horizontal stress. However, the azimuth of natural fractures and the in-situ maximum horizontal stress obtained from both image logs and micro-seismic events are limited to the wellbore locations. Wide azimuth seismic data provides an alternative way to predict the azimuth of natural fractures and maximum in-situ horizontal stress if the seismic attributes are properly calibrated with interpretations from well logs and microseismic data. To predict the azimuth of natural fractures and in-situ maximum horizontal stress, we focus our analysis on correlating the seismic attributes computed from pre-stack and post-stack seismic data with the interpreted azimuth obtained from image logs and microseismic data. The application indicates that the strike of the most positive principal curvature k1 can be used as an indicator for the azimuth of natural fractures within our study area. The azimuthal anisotropy of the dominant frequency component if offset vector title (OVT) seismic data can be used to predict the azimuth of maximum in-situ horizontal stress within our study area that is located the southern region of the Sichuan Basin, China. The predicted azimuths provide important information for the following well planning and hydraulic fracturing.

Seismic azimuthal anisotropy analysis after hydraulic fracturing

2013 ◽  
Vol 1 (2) ◽  
pp. SB27-SB36 ◽  
Author(s):  
Kui Zhang ◽  
Yanxia Guo ◽  
Bo Zhang ◽  
Amanda M. Trumbo ◽  
Kurt J. Marfurt
Keyword(s):  
Hydraulic Fracturing ◽  
Anisotropy Field ◽  
Horizontal Wells ◽  
Horizontal Stress ◽  
Azimuthal Anisotropy ◽  
Barnett Shale ◽  
Natural Fractures ◽  
Tight Sandstone ◽  
Induced Fractures ◽  
Maximum Horizontal Stress

Many tight sandstone, limestone, and shale reservoirs require hydraulic fracturing to provide pathways that allow hydrocarbons to reach the well bore. Most of these tight reservoirs are now produced using multiple stages of fracturing through horizontal wells drilled perpendicular to the present-day azimuth of maximum horizontal stress. In a homogeneous media, the induced fractures are thought to propagate perpendicularly to the well, parallel to the azimuth of maximum horizontal stress, thereby efficiently fracturing the rock and draining the reservoir. We evaluated what may be the first anisotropic analysis of a Barnett shale-gas reservoir after extensive hydraulic fracturing and focus on mapping the orientation and intensity of induced fractures and any preexisting factures, with the objective being the identification of reservoir compartmentalization and bypassed pay. The Barnett Shale we studied has near-zero permeability and few if any open natural fractures. We therefore hypothesized that anisotropy is therefore due to the regional northeast–southwest maximum horizontal stress and subsequent hydraulic fracturing. We found the anisotropy to be highly compartmentalized, with the compartment edges being defined by ridges and domes delineated by the most positive principal curvature [Formula: see text]. Microseismic work by others in the same survey indicates that these ridges contain healed natural fractures that form fracture barriers. Mapping such heterogeneous anisotropy field could be critical in planning the location and direction of any future horizontal wells to restimulate the reservoir as production drops.

A Novel Method and its Application to Define Maximum Horizontal Stress and Stress Path

2021 ◽  
Author(s):  
Jianguo Zhang ◽  
Karthik Mahadev ◽  
Stephen Edwards ◽  
Alan Rodgerson
Keyword(s):  
Fracture Initiation ◽  
Stress Path ◽  
Horizontal Stress ◽  
Geomechanical Model ◽  
Breakdown Pressure ◽  
In Situ Stresses ◽  
Fracture Closure ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress

Abstract Maximum horizontal stress (SH) and stress path (change of SH and minimum horizontal stress with depletion) are the two most difficult parameters to define for an oilfield geomechanical model. Understanding these in-situ stresses is critical to the success of operations and development, especially when production is underway, and the reservoir depletion begins. This paper introduces a method to define them through the analysis of actual minifrac data. Field examples of applications on minifrac failure analysis and operational pressure prediction are also presented. It is commonly accepted that one of the best methods to determine the minimum horizontal stress (Sh) is the use of pressure fall-off analysis of a minifrac test. Unlike Sh, the magnitude of SH cannot be measured directly. Instead it is back calculated by using fracture initiation pressure (FIP) and Sh derived from minifrac data. After non-depleted Sh and SH are defined, their apparent Poisson's Ratios (APR) are calculated using the Eaton equation. These APRs define Sh and SH in virgin sand to encapsulate all other factors that influence in-situ stresses such as tectonic, thermal, osmotic and poro-elastic effects. These values can then be used to estimate stress path through interpretation of additional minifrac data derived from a depleted sand. A geomechanical model is developed based on APRs and stress paths to predict minifrac operation pressures. Three cases are included to show that the margin of error for FIP and fracture closure pressure (FCP) is less than 2%, fracture breakdown pressure (FBP) less than 4%. Two field cases in deep-water wells in the Gulf of Mexico show that the reduction of SH with depletion is lower than that for Sh.

Numerical Simulation and Laboratory Experiments of Hydraulic Fracturing of Highly Deviated Well

2013 ◽  
Vol 275-277 ◽  
pp. 278-281 ◽  
Author(s):  
Hai Yan Zhu ◽  
Jing Gen Deng ◽  
Song Yang Li ◽  
Zi Jian Chen ◽  
Wei Yan ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Hydraulic Fracturing ◽  
Fracture Initiation ◽  
Element Model ◽  
Simulation Method ◽  
Horizontal Stress ◽  
Initiation Point ◽  
Strength Failure ◽  
Fluid Penetration ◽  
Maximum Horizontal Stress

Considering the combined action of the fluid penetration and the casing, the seepage coupled deformation finite element model of the highly deviated casing perforation well is established by using the tensile strength failure criterion and applied on the BZ25-1 oil filed. The results show that the increasing of the perforation angle and the well azimuth and the decreasing of the inclination would lead to a higher fracture initiation pressure. The fracture initiation point always locates on the wellbore face when the influence of the casing is considered. When the casing is ignored: when the perforation angle is 0°-45°, the fracture initiation point locates on the root of the tunnel; when the angle is 45°-90°, the fracture initiation point may be on the wellbore face or the perforation biased toward the maximum horizontal stress direction; when the angle is near to 90°, the hydraulic fracturing difficultly fractures the rock through the perforation tunnels. The laboratory hydraulic fracturing simulation experiments of 45° deviated well are carried through 400mm3 cement specimen so as to obtain the fracture initiation point and geometric shape under different perforation angles, the results verify the accuracy of the numerical simulation method.

scholarly journals In Situ Stress and Stress Regime in the Onshore Part of the Northeast Java Basin

2021 ◽  
Vol 44 (2) ◽  
pp. 95-105
Author(s):  
Agus M. Ramdhan
Keyword(s):  
Petroleum Industry ◽  
Horizontal Stress ◽  
In Situ Stress ◽  
Vertical Stress ◽  
Stress Regime ◽  
Severe Erosion ◽  
Tectonically Active ◽  
Minimum Horizontal Stress ◽  
Maximum Horizontal Stress

In situ stress is importance in the petroleum industry because it will significantly enhance our understanding of present-day deformation in a sedimentary basin. The Northeast Java Basin is an example of a tectonically active basin in Indonesia. However, the in situ stress in this basin is still little known. This study attempts to analyze the regional in situ stress (i.e., vertical stress, minimum and maximum horizontal stresses) magnitude and orientation, and stress regime in the onshore part of the Northeast Java Basin based on twelve wells data, consist of density log, direct/indirect pressure test, and leak-off test (LOT) data. The magnitude of vertical (  and minimum horizontal (  stresses were determined using density log and LOT data, respectively. Meanwhile, the orientation of maximum horizontal stress  (  was determined using image log data, while its magnitude was determined based on pore pressure, mudweight, and the vertical and minimum horizontal stresses. The stress regime was simply analyzed based on the magnitude of in situ stress using Anderson’s faulting theory. The results show that the vertical stress ( ) in wells that experienced less erosion can be determined using the following equation: , where  is in psi, and z is in ft. However, wells that experienced severe erosion have vertical stress gradients higher than one psi/ft ( . The minimum horizontal stress ( ) in the hydrostatic zone can be estimated as, while in the overpressured zone, . The maximum horizontal stress ( ) in the shallow and deep hydrostatic zones can be estimated using equations: and , respectively. While in the overpressured zone, . The orientation of  is ~NE-SW, with a strike-slip faulting stress regime.

Valuation of hydraulic fracturing potentials of organic-rich shales from the Anambra basin using rock mechanical properties from wireline logs

2021 ◽  
Vol 19 (3) ◽  
pp. 45-44
Author(s):  
Homa Viola Akaha-Tse ◽  
Michael Oti ◽  
Selegha Abrakasa ◽  
Charles Ugwu Ugwueze
Keyword(s):  
Mechanical Properties ◽  
Hydraulic Fracturing ◽  
Horizontal Stress ◽  
Shale Formations ◽  
In Situ Stresses ◽  
Anambra Basin ◽  
Wireline Logs ◽  
Rock Mechanical Properties ◽  
Minimum Horizontal Stress

This study was carried out to determine the rock mechanical properties relevant for hydrocarbon exploration and production by hydraulic  fracturing of organic rich shale formations in Anambra basin. Shale samples and wireline logs were analysed to determine the petrophysical, elastic, strength and in-situ properties necessary for the design of a hydraulic fracturing programme for the exploitation of the shales. The results obtained indicated shale failure in shear and barreling under triaxial test conditions. The average effective porosity of 0.06 and permeability of the order of 10-1 to 101 millidarcies showed the imperative for induced fracturing to assure fluid flow. Average Young’s modulus and Poisson’s ratio of about 2.06 and 0.20 respectively imply that the rocks are favourable for the formation and propagation of fractures during hydraulic fracking. The minimum horizontal stress, which determines the direction of formation and growth of artificially induced hydraulic fractures varies from wellto-well, averaging between 6802.62 to 32790.58 psi. The order of variation of the in-situ stresses is maximum horizontal stress>vertical stress>minimum horizontal stress which implies a reverse fault fracture regime. The study predicts that the sweet spots for the exploration and development of the shale-gas are those sections of the shale formations that exhibit high Young’s modulus, low Poisson’s ratio, and high brittleness. The in-situ stresses required for artificially induced fractures which provide pore space for shale gas accumulation and expulsion are adequate. The shales possess suitable mechanical properties to fracture during hydraulic fracturing. Application of these results will enhance the potentials of the onshore Anambra basin as a reliable component in increasing Nigeria’s gas reserves, for the improvement of the nation’s economy and energy security. Key Words: Hydraulic Fracturing, Organic-rich Shales, Rock Mechanical Properties, Petrophysical Properties, Anambra Basin

Integration of Advanced Borehole Sonic and Resistivity Image Analysis for Fracture and Stress Characterisation - Implications to Carbon Sequestration Feasibility

2021 ◽  
Author(s):  
Debashis Konwar ◽  
Abhinab Das ◽  
Chandreyi Chatterjee ◽  
Fawz Naim ◽  
Chandni Mishra ◽  
...  
Keyword(s):  
Wave Attenuation ◽  
Horizontal Stress ◽  
Open Fractures ◽  
Earth Model ◽  
Natural Fractures ◽  
Mechanical Earth Model ◽  
Induced Fractures ◽  
Maximum Horizontal Stress ◽  
Fracture Stability ◽  
Resistivity Image

Abstract Borehole resistivity images and dipole sonic data analysis helps a great deal to identify fractured zones and obtain reasonable estimates of the in-situ stress conditions of geologic formations. Especially when assessing geologic formations for carbon sequestration feasibility, borehole resistivity image and borehole sonic assisted analysis provides answers on presence of fractured zones and stress-state of these fractures. While in deeper formations open fractures would favour carbon storage, in shallower formations, on the other hand, storage integrity would be potentially compromised if these fractures get reactivated, thereby causing induced seismicity due to fluid injection. This paper discusses a methodology adopted to assess the carbon dioxide sequestration feasibility of a formation in the Newark Basin in the United States, using borehole resistivity image(FMI™ Schlumberger) and borehole sonic data (SonicScaner™ Schlumberger). The borehole image was interpreted for the presence of natural and drilling-induced fractures, and also to find the direction of the horizontal stress azimuth from the identified induced fractures. Cross-dipole sonic anisotropy analysis was done to evaluate the presence of intrinsic or stress-based anisotropy in the formation and also to obtain the horizontal stress azimuth. The open or closed nature of natural fractures was deduced from both FMI fracture filling electrical character and the Stoneley reflection wave attenuation from SonicScanner monopole low frequency waveform. The magnitudes of the maximum and minimum horizontal stresses obtained from a 1-Dimensional Mechanical Earth Model were calibrated with stress magnitudes derived from the ‘Integrated Stress Analysis’ approach which takes into account the shear wave radial variation profiles in zones with visible crossover indications of dipole flexural waves. This was followed by a fracture stability analysis in order to identify critically stressed fractures. The borehole resistivity image analysis revealed the presence of abundant natural fractures and microfaults throughout the interval which was also supported by the considerable sonic slowness anisotropy present in those intervals. Stoneley reflected wave attenuation confirmed the openness of some natural fractures identified in the resistivity image. The strike of the natural fractures and microfaults showed an almost NE-SW trend, albeit with considerable variability. The azimuth of maximum horizontal stress obtained in intervals with crossover of dipole flexural waves was also found to be NE-SW in the middle part of the interval, thus coinciding with the overall trend of natural fractures. This might indicate that the stresses in those intervals are also driven by the natural fracture network. However, towards the bottom of the interval, especially from 1255ft-1380ft, where there were indications of drilling induced fractures but no stress-based sonic anisotropy, it was found that that maximum horizontal stress azimuth rotated almost about 30 degrees in orientation to an ESE-WNW trend. The stress magnitudes obtained from the 1D-Mechanical Earth Model and Integrated Stress Analysis approach point to a normal fault stress regime in that interval. The fracture stability analysis indicated some critically stressed open fractures and microfaults, mostly towards the lower intervals of the well section. These critically stressed open fractures and microfaults present at these comparatively shallower depths of the basin point to risks associated with carbon dioxide(CO2) leakage and also to induced seismicity that might result from the injection of CO2 anywhere in or immediately below this interval.

Geomechanical characterization of a caprock-reservoir system in the Northern Appalachian Basin: Estimating spatial variation of in situ stress magnitude and orientation

2018 ◽  
Vol 6 (3) ◽  
pp. T759-T781 ◽  
Author(s):  
Samin Raziperchikolaee ◽  
Mark Kelley ◽  
Neeraj Gupta
Keyword(s):  
Mechanical Properties ◽  
Horizontal Stress ◽  
Appalachian Basin ◽  
In Situ Stress ◽  
Complex Nature ◽  
Well Log ◽  
Reservoir System ◽  
Maximum Horizontal Stress ◽  
Northern Appalachian Basin

Assessing the mechanical integrity of the caprock-reservoir system is necessary to evaluate the practical storage capacity for geologic [Formula: see text] storage. We used a combination of well-log and experimental data to estimate the statistical distribution (mean and variance) of rock mechanical properties of Cambrian-Ordovician strata within the Northern Appalachian region of Ohio and studied their heterogeneity throughout the study area. Empirical correlations between static-dynamic moduli of carbonate and sandstone formations of the Northern Appalachian Basin were developed. The state of stress (the orientation and magnitude of the maximum horizontal stress) for caprock and reservoir formations in the Cambrian-Ordovician sequence was determined at multiple well locations to understand the regional variability of these properties throughout the study area. The maximum horizontal stress ([Formula: see text]) azimuth was estimated from image logs for six wells and S-wave anisotropy data for five wells. The [Formula: see text] magnitude was estimated by analytical and numerical modeling of stresses around the wellbore calibrated to the occurrence of wellbore breakouts and drilling-induced fractures in three wells as a function of depth. The results of assessing the [Formula: see text] magnitude and stress regime in the caprock and reservoirs in the Cambrian-Ordovician sequence using rock mechanical data acquired in this study, well-log data, and drilling data indicate that both parameters vary throughout the study area. In this work, we determined how integrating different types of data from multiple wells allowed us to estimate mechanical properties and characterize the spatial variability (laterally and vertically) of in situ stress for Cambrian-Ordovician caprock and reservoirs throughout the study area. A combination of different methods — numerical, analytical, and stress polygon — is used to estimate the in situ stress magnitude, especially [Formula: see text], regionally on a formation-by-formation basis. The results of this work can be used to improve our understanding the complex nature of stress in the Northern Appalachian Basin.

Sign in / Sign up

Export Citation Format

Share Document