Noisy 4D seismic data interpretation: Case study of a Brazilian carbonate reservoir

2020 ◽  
Vol 39 (7) ◽  
pp. 488-496
Author(s):  
Lee Jean Wong ◽  
Hamed Amini ◽  
Colin MacBeth
Keyword(s):  
Seismic Data ◽  
Integrated Approach ◽  
Time Lapse ◽  
Data Interpretation ◽  
Carbonate Reservoir ◽  
Multiple Sources ◽  
Data Set ◽  
Campos Basin ◽  
Data Value ◽  
4D Seismic

A legacy seismic data set from 2001 and 2011 was used for time-lapse interpretation over a Brazilian carbonate reservoir in Field-X of Campos Basin. The acquired 4D seismic data set was noisy and initially deemed to be uninterpretable. Pressure data were limited, and the initial simulation model was poorly calibrated. All of these challenges warranted the need to establish an interdisciplinary interpretation workflow. In this paper, we introduce a tiered integrated approach to optimize data value from multiple sources. The results of interwell connectivity from production data analysis were used as a basis for assignment of 4D signal confidence flags, which were later combined with simulation-to-seismic modeling of history-matched realizations, enabling interpretation efforts of the noisy 4D seismic data set. This integrated approach led to identification of the injected water front and a potential sweet spot for an infill well.

scholarly journals Time-Lapse Seismic Monitoring of Onshore Reservoirs in Niger Delta, Field ‘K’ as a Case Study

2017 ◽  
Vol 1 (1) ◽  
pp. 23-27 ◽  
Author(s):  
A. Ogbamikhumi ◽  
T. Tralagba ◽  
E. E. Osagiede
Keyword(s):  
Seismic Data ◽  
Acoustic Impedance ◽  
Niger Delta ◽  
Rock Physics ◽  
Time Lapse ◽  
Seismic Survey ◽  
Impedance Change ◽  
Data Set ◽  
Reservoir Fluid ◽  
4D Seismic

Field ‘K’ is a mature field in the coastal swamp onshore Niger delta, which has been producing since 1960. As a huge producing field with some potential for further sustainable production, field monitoring is therefore important in the identification of areas of unproduced hydrocarbon. This can be achieved by comparing production data with the corresponding changes in acoustic impedance observed in the maps generated from base survey (initial 3D seismic) and monitor seismic survey (4D seismic) across the field. This will enable the 4D seismic data set to be used for mapping reservoir details such as advancing water front and un-swept zones. The availability of good quality onshore time-lapse seismic data for Field ‘K’ acquired in 1987 and 2002 provided the opportunity to evaluate the effect of changes in reservoir fluid saturations on time-lapse amplitudes. Rock physics modelling and fluid substitution studies on well logs were carried out, and acoustic impedance change in the reservoir was estimated to be in the range of 0.25% to about 8%. Changes in reservoir fluid saturations were confirmed with time-lapse amplitudes within the crest area of the reservoir structure where reservoir porosity is 0.25%. In this paper, we demonstrated the use of repeat Seismic to delineate swept zones and areas hit with water override in a producing onshore reservoir.

scholarly journals Time-lapse difference static correction using prestack crosscorrelations: 4D seismic image enhancement case from Ketzin

Geophysics ◽  
2014 ◽  
Vol 79 (6) ◽  
pp. B243-B252 ◽  
Author(s):  
Peter Bergmann ◽  
Artem Kashubin ◽  
Monika Ivandic ◽  
Stefan Lüth ◽  
Christopher Juhlin
Keyword(s):  
Seismic Data ◽  
Time Lapse ◽  
Data Sets ◽  
Storage Site ◽  
Data Set ◽  
Near Surface ◽  
Static Correction ◽  
Seismic Image ◽  
Static Corrections ◽  
4D Seismic

A method for static correction of time-lapse differences in reflection arrival times of time-lapse prestack seismic data is presented. These arrival-time differences are typically caused by changes in the near-surface velocities between the acquisitions and had a detrimental impact on time-lapse seismic imaging. Trace-to-trace time shifts of the data sets from different vintages are determined by crosscorrelations. The time shifts are decomposed in a surface-consistent manner, which yields static corrections that tie the repeat data to the baseline data. Hence, this approach implies that new refraction static corrections for the repeat data sets are unnecessary. The approach is demonstrated on a 4D seismic data set from the Ketzin [Formula: see text] pilot storage site, Germany, and is compared with the result of an initial processing that was based on separate refraction static corrections. It is shown that the time-lapse difference static correction approach reduces 4D noise more effectively than separate refraction static corrections and is significantly less labor intensive.

Stochastic inversion of pressure and saturation changes from time-lapse AVO data

Geophysics ◽  
2006 ◽  
Vol 71 (5) ◽  
pp. C81-C92 ◽  
Author(s):  
Helene Hafslund Veire ◽  
Hilde Grude Borgos ◽  
Martin Landrø
Keyword(s):  
Stochastic Model ◽  
Seismic Data ◽  
Synthetic Data ◽  
Time Lapse ◽  
Bayesian Framework ◽  
Reservoir Modeling ◽  
Data Set ◽  
The North ◽  
Fluid Saturation ◽  
Likelihood Model

Effects of pressure and fluid saturation can have the same degree of impact on seismic amplitudes and differential traveltimes in the reservoir interval; thus, they are often inseparable by analysis of a single stacked seismic data set. In such cases, time-lapse AVO analysis offers an opportunity to discriminate between the two effects. We quantify the uncertainty in estimations to utilize information about pressure- and saturation-related changes in reservoir modeling and simulation. One way of analyzing uncertainties is to formulate the problem in a Bayesian framework. Here, the solution of the problem will be represented by a probability density function (PDF), providing estimations of uncertainties as well as direct estimations of the properties. A stochastic model for estimation of pressure and saturation changes from time-lapse seismic AVO data is investigated within a Bayesian framework. Well-known rock physical relationships are used to set up a prior stochastic model. PP reflection coefficient differences are used to establish a likelihood model for linking reservoir variables and time-lapse seismic data. The methodology incorporates correlation between different variables of the model as well as spatial dependencies for each of the variables. In addition, information about possible bottlenecks causing large uncertainties in the estimations can be identified through sensitivity analysis of the system. The method has been tested on 1D synthetic data and on field time-lapse seismic AVO data from the Gullfaks Field in the North Sea.

Common-focus point-based target-oriented imaging approach for continuous seismic reservoir monitoring

Geophysics ◽  
2018 ◽  
Vol 83 (4) ◽  
pp. M41-M48 ◽  
Author(s):  
Hongwei Liu ◽  
Mustafa Naser Al-Ali
Keyword(s):  
Seismic Data ◽  
Rock Physics ◽  
Time Lapse ◽  
Velocity Estimation ◽  
Estimation Methods ◽  
Data Sets ◽  
Data Set ◽  
Velocity Models ◽  
Reservoir Monitoring ◽  
Focus Point

The ideal approach for continuous reservoir monitoring allows generation of fast and accurate images to cope with the massive data sets acquired for such a task. Conventionally, rigorous depth-oriented velocity-estimation methods are performed to produce sufficiently accurate velocity models. Unlike the traditional way, the target-oriented imaging technology based on the common-focus point (CFP) theory can be an alternative for continuous reservoir monitoring. The solution is based on a robust data-driven iterative operator updating strategy without deriving a detailed velocity model. The same focusing operator is applied on successive 3D seismic data sets for the first time to generate efficient and accurate 4D target-oriented seismic stacked images from time-lapse field seismic data sets acquired in a [Formula: see text] injection project in Saudi Arabia. Using the focusing operator, target-oriented prestack angle domain common-image gathers (ADCIGs) could be derived to perform amplitude-versus-angle analysis. To preserve the amplitude information in the ADCIGs, an amplitude-balancing factor is applied by embedding a synthetic data set using the real acquisition geometry to remove the geometry imprint artifact. Applying the CFP-based target-oriented imaging to time-lapse data sets revealed changes at the reservoir level in the poststack and prestack time-lapse signals, which is consistent with the [Formula: see text] injection history and rock physics.

3D DAS-VSP Illumination Modeling for CO2 Plume Migration Monitoring in Offshore Sarawak, Malaysia

2021 ◽  
Author(s):  
Pankaj Kumar Tiwari ◽  
Zoann Low ◽  
Parimal Arjun Patil ◽  
Debasis Priyadarshan Das ◽  
Prasanna Chidambaram ◽  
...  
Keyword(s):  
Dynamic Simulation ◽  
Seismic Velocity ◽  
Time Lapse ◽  
Carbonate Reservoir ◽  
Fiber Optic Sensor ◽  
Co2 Injection ◽  
Storage Site ◽  
Plume Migration ◽  
Co2 Plume ◽  
4D Seismic

Abstract Monitoring of CO2 plume migration in a depleted carbonate reservoir is challenging and demand comprehensive and trailblazing monitoring technologies. 4D time-lapse seismic exhibits the migration of CO2 plume within geological storage but in the area affected by gas chimney due to poor signal-to-noise ratio (SNR), uncertainty in identifying and interpretation of CO2 plume gets exaggerated. High resolution 3D vertical seismic profile (VSP) survey using distributed acoustic sensor (DAS) technology fulfil the objective of obtaining the detailed subsurface image which include CO2 plume migration, reservoir architecture, sub-seismic faults and fracture networks as well as the caprock. Integration of quantitative geophysics and dynamic simulation with illumination modelling dignify the capabilities of 3D DAS-VSP for CO2 plume migration monitoring. The storage site has been studied in detailed and an integrated coupled dynamic simulation were performed and results were integrated with seismic forward modeling to demonstrate the CO2 plume migration with in reservoir and its impact on seismic amplitude. 3D VSP illumination modelling was carried out by integrating reservoir and overburden interpretations, acoustic logs and seismic velocity to illustrate the subsurface coverage area at top of reservoir. Several acquisition survey geometries were simulated based on different source carpet size for effective surface source contribution for subsurface illumination and results were analyzed to design the 3D VSP survey for early CO2 plume migration monitoring. The illumination simulation was integrated with dynamic simulation for fullfield CO2 plume migration monitoring with 3D DAS-VSP by incorporating Pseudo wells illumination analysis. Results of integrated coupled dynamic simulation and 4D seismic feasibility were analyzed for selection of best well location to deploy the multi fiber optic sensor system (M-FOSS) technology. Amplitude response of synthetic AVO (amplitude vs offsets) gathers at the top of carbonate reservoir were analyzed for near, mid and far angle stacks with respect to pre-production as well as pre-injection reservoir conditions. Observed promising results of distinguishable 25-30% of CO2 saturation in depleted reservoir from 4D time-lapse seismic envisage the application of 3D DAS-VSP acquisition. The source patch analysis of 3D VSP illumination modelling results indicate that a source carpet of 6km×6km would be cos-effectively sufficient to produce a maximum of approximately 2km in diameter subsurface illumination at the top of the reservoir. The Pseudo wells illumination analysis results show that current planned injection wells would probably able to monitor early CO2 injection but for the fullfield monitoring additional monitoring wells or a hybrid survey of VSP and surface seismic would be required. The integrated modeling approach ensures that 4D Seismic in subsurface CO2 plume monitoring is robust. Monitoring pressure build-ups from 3D DAS-VSP will reduce the associated risks.

Improving 4D Seismic Data Interpretation using Geostatistical Filtering

2005 ◽  
Author(s):  
Carlos Eduardo Abreu ◽  
Nathalie Lucet and Philippe Nivlet ◽  
Jean-Jacques Royer
Keyword(s):  
Seismic Data ◽  
Data Interpretation ◽  
4D Seismic

Faster Convergence in Seismic History Matching by Dividing and Conquering the Unknowns

SPE Journal ◽  
2010 ◽  
Vol 15 (04) ◽  
pp. 1077-1088 ◽  
Author(s):  
F.. Sedighi ◽  
K.D.. D. Stephen
Keyword(s):  
Regression Analysis ◽  
Seismic Data ◽  
History Matching ◽  
Time Lapse ◽  
Business Decisions ◽  
Order Of Magnitude ◽  
Reservoir Simulation Model ◽  
The Uk ◽  
Pressure Changes ◽  
4D Seismic

Summary Seismic history matching is the process of modifying a reservoir simulation model to reproduce the observed production data in addition to information gained through time-lapse (4D) seismic data. The search for good predictions requires that many models be generated, particularly if there is an interaction between the properties that we change and their effect on the misfit to observed data. In this paper, we introduce a method of improving search efficiency by estimating such interactions and partitioning the set of unknowns into noninteracting subspaces. We use regression analysis to identify the subspaces, which are then searched separately but simultaneously with an adapted version of the quasiglobal stochastic neighborhood algorithm. We have applied this approach to the Schiehallion field, located on the UK continental shelf. The field model, supplied by the operator, contains a large number of barriers that affect flow at different times during production, and their transmissibilities are highly uncertain. We find that we can successfully represent the misfit function as a second-order polynomial dependent on changes in barrier transmissibility. First, this enables us to identify the most important barriers, and, second, we can modify their transmissibilities efficiently by searching subgroups of the parameter space. Once the regression analysis has been performed, we reduce the number of models required to find a good match by an order of magnitude. By using 4D seismic data to condition saturation and pressure changes in history matching effectively, we have gained a greater insight into reservoir behavior and have been able to predict flow more accurately with an efficient inversion tool. We can now determine unswept areas and make better business decisions.

Fluid dynamics at the base of hydrate-bearing sediments at the Vestnesa Ridge inferred from 5 years of high-resolution 4D seismic surveying

2020 ◽  
Author(s):  
Malin Waage ◽  
Stefan Bünz ◽  
Kate Waghorn ◽  
Sunny Singhorha ◽  
Pavel Serov
Keyword(s):  
High Resolution ◽  
Gas Hydrate ◽  
Seismic Data ◽  
Time Lapse ◽  
Stability Zone ◽  
Seismic Surveys ◽  
Free Gas ◽  
4D Seismic ◽  
Hydrate Bearing Sediments ◽  
Hydrate Stability

<p>The transition from gas hydrate to gas-bearing sediments at the base of the hydrate stability zone (BHSZ) is commonly identified on seismic data as a bottom-simulating reflection (BSR). At this boundary, phase transitions driven by thermal effects, pressure alternations, and gas and water flux exist. Sedimentation, erosion, subsidence, uplift, variations in bottom water temperature or heat flow cause changes in marine gas hydrate stability leading to expansion or reduction of gas hydrate accumulations and associated free gas accumulations. Pressure build-up in gas accumulations trapped beneath the hydrate layer may eventually lead to fracturing of hydrate-bearing sediments that enables advection of fluids into the hydrate layer and potentially seabed seepage. Depletion of gas along zones of weakness creates hydraulic gradients in the free gas zone where gas is forced to migrate along the lower hydrate boundary towards these weakness zones. However, due to lack of “real time” data, the magnitude and timescales of processes at the gas hydrate – gas contact zone remains largely unknown. Here we show results of high resolution 4D seismic surveys at a prominent Arctic gas hydrate accumulation – Vestnesa ridge - capturing dynamics of the gas hydrate and free gas accumulations over 5 years. The 4D time-lapse seismic method has the potential to identify and monitor fluid movement in the subsurface over certain time intervals. Although conventional 4D seismic has a long history of application to monitor fluid changes in petroleum reservoirs, high-resolution seismic data (20-300 Hz) as a tool for 4D fluid monitoring of natural geological processes has been recently identified.<br><br>Our 4D data set consists of four high-resolution P-Cable 3D seismic surveys acquired between 2012 and 2017 in the eastern segment of Vestnesa Ridge. Vestnesa Ridge has an active fluid and gas hydrate system in a contourite drift setting near the Knipovich Ridge offshore W-Svalbard. Large gas flares, ~800 m tall rise from seafloor pockmarks (~700 m diameter) at the ridge axis. Beneath the pockmarks, gas chimneys pierce the hydrate stability zone, and a strong, widespread BSR occurs at depth of 160-180 m bsf. 4D seismic datasets reveal changes in subsurface fluid distribution near the BHSZ on Vestnesa Ridge. In particular, the amplitude along the BSR reflection appears to change across surveys. Disappearance of bright reflections suggest that gas-rich fluids have escaped the free gas zone and possibly migrated into the hydrate stability zone and contributed to a gas hydrate accumulation, or alternatively, migrated laterally along the BSR. Appearance of bright reflection might also indicate lateral migration, ongoing microbial or thermogenic gas supply or be related to other phase transitions. We document that faults, chimneys and lithology constrain these anomalies imposing yet another control on vertical and lateral gas migration and accumulation. These time-lapse differences suggest that (1) we can resolve fluid changes on a year-year timescale in this natural seepage system using high-resolution P-Cable data and (2) that fluids accumulate at, migrate to and migrate from the BHSZ over the same time scale.</p>

Pore-pressure detection sensitivities tested with time-lapse seismic data

Geophysics ◽  
2005 ◽  
Vol 70 (6) ◽  
pp. O39-O50 ◽  
Author(s):  
Øyvind Kvam ◽  
Martin Landrø
Keyword(s):  
Pore Pressure ◽  
Seismic Data ◽  
Time Lapse ◽  
Pressure Increase ◽  
Burial Depth ◽  
Velocity Analysis ◽  
Seismic Velocities ◽  
Data Set ◽  
Pore Pressure Prediction ◽  
Velocity Changes

In an exploration context, pore-pressure prediction from seismic data relies on the fact that seismic velocities depend on pore pressure. Conventional velocity analysis is a tool that may form the basis for obtaining interval velocities for this purpose. However, velocity analysis is inaccurate, and in this paper we focus on the possibilities and limitations of using velocity analysis for pore-pressure prediction. A time-lapse seismic data set from a segment that has undergone a pore-pressure increase of 5 to 7 MPa between the two surveys is analyzed for velocity changes using detailed velocity analysis. A synthetic time-lapse survey is used to test the sensitivity of the velocity analysis with respect to noise. The analysis shows that the pore-pressure increase cannot be detected by conventional velocity analysis because the uncertainty is much greater than the expected velocity change for a reservoir of the given thickness and burial depth. Finally, by applying amplitude-variation-with-offset (AVO) analysis to the same data, we demonstrate that seismic amplitude analysis may yield more precise information about velocity changes than velocity analysis.

Sign in / Sign up

Export Citation Format

Share Document