2D Numerical Simulation of a Wind Turbine De-Icing System, Using Cycled Heating

2007 ◽  
Vol 31 (1) ◽  
pp. 33-42 ◽  
Author(s):  
L. Battisti ◽  
R. Fedrizzi
Keyword(s):  
Numerical Simulation ◽  
Wind Turbine ◽  
2D Numerical Simulation

scholarly journals 2D Numerical Simulation and Sensitive Analysis of H-Darrieus Wind Turbine

2018 ◽  
Vol 7 (1) ◽  
pp. 23 ◽  
Author(s):  
Seyed Mohammad E. Saryazdi ◽  
Mehrdad Boroushaki
Keyword(s):  
Numerical Simulation ◽  
Sensitivity Analysis ◽  
Wind Turbine ◽  
Turbulence Models ◽  
Effective Parameter ◽  
Computational Domain ◽  
Effective Parameters ◽  
Sensitive Analysis ◽  
Best Value ◽  
2D Numerical Simulation

Recently, a lot of attention has been devoted to the use of Darrieus wind turbines in urban areas. The aerodynamics of a Darrieus turbine are very complex due to dynamic stall and changing forces on the turbine triggered by changing horizontal angles. In this study, the aerodynamics of H-rotor vertical axis wind turbine (VAWT) has been studied using computational fluid dynamics via two different turbulence models. Shear stress transport (SST) k-ω turbulence model was used to simulate a 2D unsteady model of the H-Darrieus turbine. In order to complete this simulation, sensitivity analysis of the effective turbine parameters such as solidity factor, airfoil shape, wind velocity and shaft diameter were done. To simulate the flow through the turbine, a 2D simplified computational domain has been generated. Then fine mesh for each case consisting of different turbulence models and dimensions has been generated. Each mesh in this simulation dependent on effective parameters consisted of domain size, mesh quality, time step and total revolution. The sliding mesh method was applied to evaluate the unsteady interaction between the stationary and rotating components. Previous works just simulated turbine, while in our study sensitivity analysis of effective parameters was done. The simulation results closely match the experimental data, providing an efficient and reliable foundation to study wind turbine aerodynamics. This also demonstrates computing the best value of the effective parameter. The sensitivity analysis revealed best value of the effective parameter that could be used in the process of designing turbine. This work provides the first step in developing an accurate 3D aerodynamic modeling of Darrieus wind turbines.Article History: Received :August 19th 2017; Received: December 15th 2017; Accepted: Januari 14th 2018; Available onlineHow to Cite This Article: Saryazdi, S. M. E. and Boroushaki, M. (2018) 2D Numerical Simulation and Sensitive Analysis of H-Darrieus Wind Turbine. Int. Journal of Renewable Energy Development,7(1),23-34https://doi.org/10.14710/ijred.7.1.23-24

scholarly journals Numerically and Experimentally Verified Design of a Small Wind Turbine with Injection Molded Blade

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 776
Author(s):  
Byunghui Kim ◽  
Sang-June Park ◽  
Seokyoung Ahn ◽  
Myung-Gon Kim ◽  
Hyung-Gun Yang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Power Systems ◽  
Wind Turbine ◽  
Wind Power ◽  
Offshore Wind ◽  
Power Coefficient ◽  
Manufacturing Method ◽  
Small Wind Turbine ◽  
Verification Methods ◽  
Wind Power Systems

Although mega-watt class onshore and offshore wind power systems are used to generate power due to their cost-effectiveness, small wind power systems are important for household usages. Researchers have focused on aerodynamic characteristics as a conceptual design from their previous studies on Archimedes spiral wind turbines. Here, we verified the design of a small wind turbine AWM-750D (100 W capacity) via both numerical simulation and experimentation. We used commercial code ANSYS CFX for numerical simulation and compared turbulence models and surface roughness for determining the performance. To obtain reliable and robust blades, we analyzed the effective manufacturing method with Moldflow. Through a test with an open-suction type atmospheric boundary layer wind tunnel, we varied wind speed from 4.0 m/s to the rated value of 12.5 m/s and obtained 106 W, equivalent to a power coefficient of 0.205. In addition, we compared the numerical and experimental power vs. rotational speed and found the former is 6.5% lower than the latter. In this study, we proved that numerical simulations can act as design verification methods to predict wind turbine performances and reliable manufacturing. Through our research, we provided the prototype of a small wind turbine with 100 W to act as an efficient electric power supplier for households and also the stable manufacturing process for complex spiral blades using injection molding.

scholarly journals COMPUTATIONAL FLUID DYNAMICS STUDY OF DUSTY AIR FLOW OVER NACA 63415 AIRFOIL FOR WIND TURBINE APPLICATIONS

2017 ◽  
Vol 79 (7-3) ◽  
Author(s):  
Iham F. Zidane ◽  
Khalid M. Saqr ◽  
Greg Swadener ◽  
Xianghong Ma ◽  
Mohamed F. Shehadeh
Keyword(s):  
Numerical Simulation ◽  
Wind Turbine ◽  
South African ◽  
Stokes Equations ◽  
Lift Coefficient ◽  
Turbine Blades ◽  
Aerodynamic Performance ◽  
Accurate Estimation ◽  
African Countries ◽  
Sand Particles

Gulf and South African countries have enormous potential for wind energy. However, the emergence of sand storms in this region postulates performance and reliability challenges on wind turbines. This study investigates the effects of debris flow on wind turbine blade performance. In this paper, two-dimensional incompressible Navier-Stokes equations and the transition SST turbulence model are used to analyze the aerodynamic performance of NACA 63415 airfoil under clean and sandy conditions. The numerical simulation of the airfoil under clean surface condition is performed at Reynolds number 460×103, and the numerical results have a good consistency with the experimental data. The Discrete Phase Model has been used to investigate the role sand particles play in the aerodynamic performance degradation. The pressure and lift coefficients of the airfoil have been computed under different sand particles flow rates. The performance of the airfoil under different angle of attacks has been studied. Results showed that the blade lift coefficient can deteriorate by 28% in conditions relevant to the Gulf and South African countries sand storms. As a result, the numerical simulation method has been verified to be economically available for accurate estimation of the sand particles effect on the wind turbine blades.

Dynamic Response of a Spar-Type Floating Wind Turbine at Power Generation

2014 ◽  
Author(s):  
Tomoaki Utsunomiya ◽  
Shigeo Yoshida ◽  
Soichiro Kiyoki ◽  
Iku Sato ◽  
Shigesuke Ishida
Keyword(s):  
Numerical Simulation ◽  
Power Generation ◽  
Dynamic Response ◽  
Wind Turbine ◽  
Prestressed Concrete ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Floating Foundation ◽  
Mooring Dynamics ◽  
Nagasaki Prefecture

In this paper, dynamic response of a Floating Offshore Wind Turbine (FOWT) with spar-type floating foundation at power generation is presented. The FOWT mounts a 100kW wind turbine of down-wind type, with the rotor’s diameter of 22m and a hub-height of 23.3m. The floating foundation consists of PC-steel hybrid spar. The upper part is made of steel whereas the lower part made of prestressed concrete segments. The FOWT was installed at the site about 1km offshore from Kabashima Island, Goto city, Nagasaki prefecture on June 11th, 2012. Since then, the field measurement had been made until its removal in June 2013. In this paper, the dynamic behavior during the power generation is presented, where the comparison with the numerical simulation by aero-hydro-servo-mooring dynamics coupled program is made.

Sign in / Sign up

Export Citation Format

Share Document