Experimental and Numerical Investigation of Large Scale Effect on Buckling and Post-Buckling Behavior of Tubular Structures

2020 ◽  
Author(s):  
CHAO ZHANG ◽  
K. T. TAN
Keyword(s):  
Numerical Investigation ◽  
Scale Effect ◽  
Large Scale ◽  
Tubular Structures ◽  
Buckling Behavior ◽  
Post Buckling

Investigations on the Local Buckling Response of High Strength Linepipe

2008 ◽  
Author(s):  
Ali Fatemi ◽  
Shawn Kenny ◽  
Millan Sen ◽  
Joe Zhou ◽  
Farid Taheri ◽  
...  
Keyword(s):  
Large Scale ◽  
Local Buckling ◽  
High Strength ◽  
Order Effects ◽  
Geometric Imperfections ◽  
Mesh Topology ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Element Simulator ◽  
Experimental Response

A numerical modeling procedure was developed, using the finite-element simulator ABAQUS/Standard, to predict the local buckling and post-buckling response of high strength pipelines subject to combined state of loading. The numerical procedures were calibrated using test data from large-scale experiments examining the local buckling of high strength linepipe. The numerical model’s response was consistent with the measured experimental response for predicting the local buckling behavior well into the post-yield range. A parametric study was conducted that examined element selection, mesh topology, second-order effects, geometric imperfections and material properties. The results from this study are presented.

Buckling Behavior of Tire Breaker Structure

1983 ◽  
Vol 11 (1) ◽  
pp. 3-19
Author(s):  
T. Akasaka ◽  
S. Yamazaki ◽  
K. Asano
Keyword(s):  
Elastic Foundation ◽  
Elastic Moduli ◽  
Wave Length ◽  
Bending Moment ◽  
Experimental Results ◽  
Automobile Tire ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Steel Cord ◽  
Interlaminar Shear

Abstract The buckled wave length and the critical in-plane bending moment of laminated long composite strips of cord-reinforced rubber sheets on an elastic foundation is analyzed by Galerkin's method, with consideration of interlaminar shear deformation. An approximate formula for the wave length is given in terms of cord angle, elastic moduli of the constituent rubber and steel cord, and several structural dimensions. The calculated wave length for a 165SR13 automobile tire with steel breakers (belts) was very close to experimental results. An additional study was then conducted on the post-buckling behavior of a laminated biased composite beam on an elastic foundation. This beam is subjected to axial compression. The calculated relationship between the buckled wave rise and the compressive membrane force also agreed well with experimental results.

Appraisal of Allowable Loads by Simplified Rules

1986 ◽  
Vol 108 (2) ◽  
pp. 131-137
Author(s):  
D. Moulin
Keyword(s):  
Experimental Investigation ◽  
Plastic Region ◽  
Thin Structures ◽  
Geometric Imperfections ◽  
Buckling Behavior ◽  
Simplified Method ◽  
Post Buckling ◽  
Initial Geometric Imperfections ◽  
Fast Breeder Reactors ◽  
Breeder Reactors

This paper presents a simplified method to analyze the buckling of thin structures like those of Liquid Metal Fast Breeder Reactors (LMFBR). The method is very similar to those used for the buckling of beams and columns with initial geometric imperfections, buckling in the plastic region. Special attention is paid to the strain hardening of material involved and to possible unstable post-buckling behavior. The analytical method uses elastic calculations and diagrams that account for various initial geometric defects. An application of the method is given. A comparison is made with an experimental investigation concerning a representative LMFBR component.

Numerical investigation on the buckling behavior of damaged steel members constrained by outer tubes

Structures ◽  
2021 ◽  
Vol 34 ◽  
pp. 1068-1079
Author(s):  
Jian Feng ◽  
Shuxuan Ren ◽  
Qian Zhang ◽  
Yixiang Xu ◽  
Jianyu Li ◽  
...  
Keyword(s):  
Numerical Investigation ◽  
Steel Members ◽  
Buckling Behavior

Geometrical Stiffness of Thin-Walled I-Beam Element Based on Rigid-Beam Assemblage Concept

2012 ◽  
Vol 28 (1) ◽  
pp. 97-106 ◽  
Author(s):  
J. D. Yau ◽  
S.-R. Kuo
Keyword(s):  
Stiffness Matrix ◽  
Virtual Work ◽  
Bending Moment ◽  
Beam Element ◽  
Narrow Beam ◽  
Cross Sectional ◽  
Geometric Stiffness ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Thin Walled

ABSTRACTUsing conventional virtual work method to derive geometric stiffness of a thin-walled beam element, researchers usually have to deal with nonlinear strains with high order terms and the induced moments caused by cross sectional stress results under rotations. To simplify the laborious procedure, this study decomposes an I-beam element into three narrow beam components in conjunction with geometrical hypothesis of rigid cross section. Then let us adopt Yanget al.'s simplified geometric stiffness matrix [kg]12×12of a rigid beam element as the basis of geometric stiffness of a narrow beam element. Finally, we can use rigid beam assemblage and stiffness transformation procedure to derivate the geometric stiffness matrix [kg]14×14of an I-beam element, in which two nodal warping deformations are included. From the derived [kg]14×14matrix, it can take into account the nature of various rotational moments, such as semi-tangential (ST) property for St. Venant torque and quasi-tangential (QT) property for both bending moment and warping torque. The applicability of the proposed [kg]14×14matrix to buckling problem and geometric nonlinear analysis of loaded I-shaped beam structures will be verified and compared with the results presented in existing literatures. Moreover, the post-buckling behavior of a centrally-load web-tapered I-beam with warping restraints will be investigated as well.

Sign in / Sign up

Export Citation Format

Share Document