scholarly journals Research of the Vibration and Noise Controlling About the Automobile Exhaust Pipe

2017 ◽  
Author(s):  
Chun-liang LI ◽  
Hong LI ◽  
Fang LEI
Keyword(s):  
Exhaust Pipe ◽  
Automobile Exhaust

Hydroforming analysis of exhaust pipe connectors

2020 ◽  
Vol 62 (9) ◽  
pp. 901-908
Author(s):  
Rıza Marangoz ◽  
S. Ozmen Eruslu ◽  
I. Savaş Dalmış
Keyword(s):  
Exhaust Pipe

ALLEGHENY LUDLUM MF-2

Alloy Digest ◽  
1972 ◽  
Vol 21 (4) ◽  
Keyword(s):  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Tensile Properties ◽  
Heat Treating ◽  
Chromium Steel ◽  
Automobile Exhaust ◽  
Temperature Performance ◽  
Exhaust Systems

Abstract ALLEGHENY LUDLUM MF-2 is a 12% chromium steel that was developed initially for use in automobile exhaust systems. This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-270. Producer or source: Allegheny Ludlum Corporation.

scholarly journals Small Cogeneration Unit with Heat and Electricity Storage

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2102
Author(s):  
Josef Stetina ◽  
Michael Bohm ◽  
Michal Brezina
Keyword(s):  
Internal Combustion Engine ◽  
Cooling System ◽  
Combustion Engine ◽  
Catalytic Converter ◽  
Storage System ◽  
Internal Combustion ◽  
Energy Storage System ◽  
Balance Model ◽  
Exhaust Pipe ◽  
Water Storage Tank

A micro cogeneration unit based on a three-cylinder internal combustion engine, Skoda MPI 1.0 L compressed natural gas (CNG), with an output of 25 kW at 3000 RPM is proposed in this paper. It is a relatively simple engine, which is already adopted by the manufacturer to operate on CNG. The engine life and design correspond to the original purpose of use in the vehicle. A detailed dynamic model was created in the GT-SUITE environment and implemented into an energy balance model that includes its internal combustion engine, heat exchangers, generator, battery storage, and water storage tank. The 1D internal combustion engine model provides us with information on engine start-up time, actual effective power, friction power, and the amount of heat going to the cooling system and exhaust pipe. The catalytic converter was removed from the exhaust pipe, and the engine was always operating at full load; thus, engine power control is not considered. An energy storage system for an island operation of the entire power unit for a large, detached house was designed to withstand accumulated energy for a few days in the case of a breakout. To reach a low initial system cost, the possible implementation of worn-out battery packs toward emission reduction in terms of the second life of the battery is proposed. The energy and emission balance are carried out, and the service life of the engine is also discussed.

scholarly journals Investigation into the Relationship between Super-Knock and Misfires in an SI GDI Engine

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2099
Author(s):  
Jian Gao ◽  
Anren Yao ◽  
Yeyi Zhang ◽  
Guofan Qu ◽  
Chunde Yao ◽  
...  
Keyword(s):  
Pressure Fluctuation ◽  
Direct Injection ◽  
Exhaust Valve ◽  
Gasoline Direct Injection ◽  
Exhaust Pipe ◽  
Pressure Transducers ◽  
Spark Plug ◽  
Si Engines ◽  
Gdi Engine ◽  
The Relationship

The super-knock poses new challenges for further increasing the power density of spark ignition (SI) engines. The critical factors and mechanism connecting regarding the occurrence of super-knock are still unclear. Misfire is a common phenomenon in SI engines that the mixture in cylinder is not ignited normally, which is often caused by spark plug failure. However, the effect of misfire on engine combustion has not been paid enough attention to, particularly regarding connection to super-knock. The paper presents the results of experimental investigation into the relationship between super-knock and misfires at low speed and full load conditions. In this work, a boosted gasoline direct injection (GDI) engine with an exhaust manifold integrated in the cylinder head was employed. Four piezoelectric pressure transducers were used to acquire the data of a pressure trace in cylinder. The spark plugs of four cylinders were controlled manually, of which the ignition system could be cut off as demanded. In particular, a piezoelectric pressure transducer was installed at the exhaust pipe before the turbocharger to capture the pressure traces in the exhaust pipe. The results illustrated that misfires in one cylinder would cause super-knock in the other cylinders as well as the cylinder of itself. After one cylinder misfired, the unburned mixture would burn in the exhaust pipe to produce oscillating waves. The abnormal pressure fluctuation in the exhaust pipe was strongly correlated with the occurrence of super-knock. The sharper the pressure fluctuation, the greater the intensity of knock in the power cylinder. The cylinder whose exhaust valve overlapped with the exhaust valve of the misfired cylinder was prone to super-knock.

Sign in / Sign up

Export Citation Format

Share Document