Techniques for Reducing the Diesel Engine Noise(Minor Special Issue on the Internal Combustion Engine)

1976 ◽  
Vol 79 (694) ◽  
pp. 846-852
Author(s):  
Kazuomi OCHIAI
Keyword(s):  
Diesel Engine ◽  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Special Issue ◽  
Engine Noise

Analysis and Research of the Combustion Process of YN4100QB Diesel Engine

2013 ◽  
Vol 744 ◽  
pp. 35-39
Author(s):  
Lei Ming Shi ◽  
Guang Hui Jia ◽  
Zhi Fei Zhang ◽  
Zhong Ming Xu
Keyword(s):  
Diesel Engine ◽  
Internal Combustion Engine ◽  
Combustion Chamber ◽  
Optimization Design ◽  
Combustion Engine ◽  
Geometric Model ◽  
Combustion Process ◽  
Internal Combustion ◽  
Engine Combustion ◽  
Exhaust Noise

In order to obtain the foundation to the research on the Diesel Engine YN4100QB combustion process, exhaust, the optimal design of combustion chamber and the useful information for the design of exhaust muffler, the geometric model and mesh model of a type internal combustion engine are constructed by using FIRE software to analyze the working process of internal combustion engine. Exhaust noise is the main component of automobile noise in the study of controlling vehicle noise. It is primary to design a type of muffler which is good for agricultural automobile engine matching and noise reduction effect. The present car mufflers are all development means. So it is bound to cause the long cycle of product development and waste of resources. Even sometimes not only can it not reach the purpose of reducing the noise but also it leads to reduce the engine dynamic. The strength of the exhaust noise is closely related to engine combustion temperature and pressure. The calculation and initial parameters are applied to the software based on the combustion model and theory. According to the specific operation process of internal combustion engine. Five kinds of common operation condition was compiled. It is obtained for the detailed distribution parameters of combusted gas temperature pressure . It is also got for flow velocity of the fields in cylinder and given for the relation of the parameters and crankshaft angle for the further research. At the same time NOx emissions situation are got. The numerical results show that not only does it provide the 3D distribution data in different crank shaft angle inside the cylinder in the simulation of combustion process, but also it provides a basis for the engine combustion ,emission research, the optimization design of the combustion chamber and the useful information for the designs of muffler.

scholarly journals OPTIMIZATION OF WASTE MOTOR OIL IN SHIP DIESEL WITH HIGH BOOST BY WEAR CRITERION

2018 ◽  
pp. 78-86
Author(s):  
Maxim Igorevich Tarasov ◽  
Georgy Alexandrovich Gauk ◽  
Liudmila Anatolievna Semeniuk
Keyword(s):  
Diesel Engine ◽  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Optimal Level ◽  
Engine Oil ◽  
Resource Saving ◽  
Engine Wear ◽  
The Impact

The results of modeling the impact of oil burning on the condition of the ship forced trunk piston diesel engine when using lubricants with different operating properties. The dependence of wear rate on oil fume, the quality of used lubricants and marine diesel forcing is obtained by modeling wear using the theory of planning experiments. The area of minimal wear has been determined. There has been detected the most efficient waste oil providing favorable conditions for resource-saving operation of the internal combustion engine. It is inferred that reduction of engine oil fume changes the main parameters of its aging. At the same time, the intensity of oil aging in main directions and of engine wear reduce from 0.75 to 2.25 g/(kW∙h), whereas the fume increases. Its further increase is accompanied by an increase in the rate of oil aging and engine wear. The detected "fracture" depending on И( g y) after passing the border g yopt = 2.25-2.5 g/(kW∙h) is stipulated by different ratio of oil exchange in the lubrication system and the ingress of gases into the crankcase. There has been determined the degree of oil burning, at which sludging and lacquer formation of the internal combustion engine is least intense. The smallest carbon deposits on pistons and in the crankcase of the engine can be observed when the diesel engine is operating in the zone of optimal carbonation. Experimentally, the dependence of tribotechnical properties, in particular, wear of insoluble products of oil aging has been detected at different degrees of oil burning. It is revealed that these characteristics also depend on the quality of the used fuels and lubricants and the conditions of formation and turnover of the oil film on the mirror of the cylinder, the thermal effect on it of the engine workflow. The result of simulation is the prediction of resource-saving operation of marine trunk diesel engines by maintaining oil fume at the optimal level.

Sign in / Sign up

Export Citation Format

Share Document