Analysis of the EGR System Performance in Modern Diesel Engines

Exhaust Gas Recirculation (EGR) is extensively employed in diesel combustion engines to achieve NOx emission targets. The EGR is often cooled in order to increase the effectiveness of the strategy, even though this leads to a further undesired impact on PM and HC. Experimental tests were carried out on a diesel engine at a dynamometer rig under steady-state speed and load working conditions that were considered relevant for the New European Driving Cycle. Two different shell and tube-type EGR coolers were compared, in terms of the pressure and temperature of the exhaust and intake lines, to evaluate thermal effectiveness and induced pumping losses. All the relevant engine parameters were acquired along EGR trade-off curves, in order to perform a detailed comparison of the two coolers. The effect of intake throttling operation on increasing the EGR ratio was also investigated. A purposely designed aging procedure was run in order to characterize the deterioration of the thermal effectiveness and verify whether clogging of the EGR cooler occurred. The EGR mass flow-rate dependence on the pressure and temperature upstream of the turbine as well as the pressure downstream of the EGR control valve was modeled by means of the expression for convergent nozzles. The restricted flow-area at the valve-seat passage and the discharge coefficient were accurately determined as functions of the valve lift.

Model-Based Calibration of a Biogas Engine Control System

Pipeline natural gas composition is monitored and controlled in order to deliver high quality, relatively consistent gas quality in terms of heating value and detonation characteristics to end users. The consistency of this fuel means gas-fired engines designed for electrical power generation (EPG) applications can be highly optimized. As new sources of high quality natural gas are found, the demand for these engines is growing. At the same time there is also an increasing need for EPG engines that can handle fuels that have wide swings in composition over a relatively short period of time. The application presented in this paper is an engine paired with an anaerobic digester that accepts an unpredictable and varying feedstock. As is typical in biogas applications, there are exhaust stream contaminants that preclude the use of an oxygen or NOx sensor for emissions feedback control. The difficulty with such a scenario is the ability to hold a given exhaust gas emission level as the fuel composition varies. One challenge is the design of the combustion system hardware. This design effort includes the proper selection of compression ratio, valve events, ignition timing, turbomachinery, etc. Often times simulation tools, such as a crank-angle resolved engine model, are used in the development of such systems in order to predict performance and reduce development time and hardware testing. The second challenge is the control system and how to implement a robust control capable of optimizing engine performance while maintaining emissions compliance. Currently there are limited options for an OEM control system capable of dealing with fuels that have wide swings in composition. Often times the solution for the engine packager is to adopt an aftermarket control system and apply this in place of the control system delivered on the engine. The disadvantage to this approach is that the aftermarket controller is not calibrated and so the packager is faced with the task of developing an entire engine calibration at a customer site. The controller must function well enough that it will run reliably during plant start-up and then eventually prove capable of holding emissions under typical operating conditions. This paper will describe the novel use of a crank-angle resolved four-stroke engine cycle model to develop an initial set of calibration values for an aftermarket control system. The paper will describe the plant operation, implementation of the aftermarket controller, the model-based calibration methodology and the commissioning of the engine.

Modelling and CFD Simulation of Effects of Spray Penetration on Piston Bowl Impingement in a DI Diesel Engine for Biodiesel-Diesel Blend (B20)

The effect of spray penetration distance on fuel impingement on piston bowl of a 7.4 kW diesel engine for biodiesel-diesel blend (B20) was studied using modeling and CFD simulation. As the peak inline fuel pressure increased from 460 bar with base diesel to 480 bar with B20, the spray penetration distance (fuel jet) increases. It is observed from the study that the jet tip hits on piston bowl resulting to fuel impingement which is one of durability issues for use of biodiesel blend in the diesel engine. In addition to this, the simulation of effects of different injection pressures up to 2000 bar on spray penetration distance and wall impingement were also studied. The penetration distance increases with increase the in-line fuel pressure and it decreases with decrease nozzle hole diameter. The fuel impingement on piston bowl of the engine with high injection pressure (typically 1800 bar) can be avoided by decreasing the nozzle diameter from 0.19 mm to 0.1 mm. Increase in swirl ratio could also reduce fuel impingement problem.

Numerical Comparative Analysis of In-Cylinder Tumble Flow Structures in Small PFI Engines Equipped by Heads Having Different Shapes and Squish Areas

For increasing the thermal engine efficiency, faster combustion and low cycle-to-cycle variation are required. In PFI engines the organization of in-cylinder flow structure is thus mandatory for achieving increased efficiency. In particular the formation of a coherent tumble vortex with dimensions comparable to engine stroke largely promotes proper turbulence production extending the engine tolerance to dilute/lean mixture. For motorbike and scooter applications, tumble has been considered as an effective way to further improve combustion system efficiency and to achieve emission reduction since layout and weight constraints limit the adoption of more advanced concepts. In literature chamber geometry was found to have a significant influence on bulk motion and turbulence levels at ignition time, while intake system influences mainly the formation of tumble vortices during suction phase. The most common engine parameters believed to affect in-cylinder flow structure are: 1. Intake duct angle; 2. Inlet valve shape and lift; 3. Piston shape; 4. Pent-roof angle. The present paper deals with the computational analysis of three different head shapes equipping a scooter/motorcycle engine and their influence on the tumble flow formation and breakdown, up to the final turbulent kinetic energy distribution at spark plug. The engine in analysis is a 3-valves pent-roof motorcycle engine. The three dimensional CFD simulations were run at 6500 rpm with AVL FIRE code on the three engines characterised by the same piston, valve lift, pent-roof angle and compression ratio. They differ only in head shape and squish areas. The aim of the present paper is to demonstrate the influence of different head shapes on in-cylinder flow motion, with particular care to tumble motion and turbulence level at ignition time. Moreover, an analysis of the mutual influence between tumble motion and squish motion was carried out in order to assess the role of both these motions in promoting a proper level of turbulence at ignition time close to spark plug in small 3-valves engines.

CFD Modelling of the Effects of Injection Timing on the Combustion Process and Emissions in an HSDI Diesel Engine

High-Speed Direct Injection (HSDI) diesel engines are increasingly used in automotive applications due to superior fuel economy. An advanced CFD simulation has been carried out to analyze the effect of injection timing on combustion process and emission characteristics in a four valves 2.0L Ford diesel engine. The calculation was performed from intake valve closing (IVC) to exhaust valve opening (EVO) at constant speed of 1600 rpm. Since the work was concentrated on the spray injection, mixture formation and combustion process, only a 60° sector mesh was employed for the calculations. For combustion modeling, an improved version of the Coherent Flame Model (ECFM-3Z) has been applied accompanied with advanced models for emission modeling. The results of simulation were compared against experimental data. Good agreement of calculated and measured in-cylinder pressure trace and pollutant formation trends were observed for all investigated operating points. In addition, the results showed that the current CFD model can be applied as a beneficial tool for analyzing the parameters of the diesel combustion under HSDI operating condition.

Powertrain Waste Heat Recovery: A Systems Approach to Maximize Drivetrain Efficiency

Up to 65% of the energy produced in an internal combustion engine is dissipated to the engine cooling circuit and exhaust gases [1]. Therefore, recovering a portion of this heat energy is a highly effective solution to improve engine and drivetrain efficiency and to reduce CO2 emissions, with existing vehicle and powertrain technologies [2,3]. This paper details a practical approach to the utilization of powertrain waste heat for light vehicle engines to reduce fuel consumption. The “Systems Approach” as described in this paper recovers useful energy from what would otherwise be heat energy wasted into the environment, and effectively distributes this energy to the transmission and engine oils thus reducing the oil viscosities. The focus is on how to effectively distribute the available powertrain heat energy to optimize drivetrain efficiency for light duty vehicles, minimizing fuel consumption during various drive cycles. To accomplish this, it is necessary to identify the available powertrain heat energy during any drive cycle and cold start conditions, and to distribute this energy in such a way to maximize the overall efficiency of the drivetrain.

Retracted: “Development of an Electronic Fuel Injection System for a 4-Stroke Locomotive Diesel Engine” [ASME 2012 Internal Combustion Engine Division Spring Technical Conference, Torino, Piemonte, Italy, May 6–9, 2012, Conference Sponsors: Internal Combustion Engine Division, ISBN: 978-0-7918-4466-3, Copyright © 2012 by ASME. Paper No. ICES2012-81163, pp. 93-99; 7 pages; doi: 10.1115/ICES2012-81163]

Reason: This paper was removed as a dual publication. Please see https://asmedigitalcollection.asme.org/ICEF/proceedings/ICEF2012/55096/83/238117. October 2, 2020. Copyright © 2020 by ASME

Effects of H2 Addition to CNG Blends on Cycle-to-Cycle and Cylinder-to-Cylinder Combustion Variation in an SI Engine

An experimental investigation and a burning-rate analysis have been performed on a production 1.4 liter CNG (compressed natural gas) engine fueled with methane-hydrogen blends. The engine features a pent-roof combustion chamber, four valves per cylinder and a centrally located spark plug. The experimental tests have been carried out in order to quantify the cycle-to-cycle and the cylinder-to-cylinder combustion variation. Therefore, the engine has been equipped with four dedicated piezoelectric pressure transducers placed on each cylinder and located by the spark plug. At each test point, in-cylinder pressure, fuel consumption, induced air mass flow rate, pressure and temperature at different locations on the engine intake and exhaust systems as well as ‘engine-out’ pollutant emissions have been measured. The signals correlated to the engine operation have been acquired by means of a National Instruments PXI-DAQ system and a home developed software. The acquired data have then been processed through a combustion diagnostic tool resulting from the integration of an original multizone thermodynamic model with a CAD procedure for the evaluation of the burned-gas front geometry. The diagnostic tool allows the burning velocities to be computed. The tests have been performed over a wide range of engine speeds, loads and relative air-fuel ratios (up to the lean operation). For stoichiometric operation, the addition of hydrogen to CNG has produced a bsfc reduction ranging between 2 to 7% and a bsTHC decrease up to the 40%. These benefits have appeared to be even higher for lean mixtures. Moreover, hydrogen has shown to significantly enhance the combustion process, thus leading to a sensibly lower cycle-to-cycle variability. As a matter of fact, hydrogen addition has generally resulted into extended operation up to RAFR = 1.8. Still, a discrepancy in the abovementioned conclusions was observed depending on the engine cylinder considered.

Understanding the Acoustic Oscillations Observed in the Injection Rate of a Common-Rail DI Diesel Injector

Measuring the rate of injection of a common-rail injector is one of the first steps for diesel engine development. At the same time, this information is of prime interest for engine research and modeling as it drives spray development and mixing. On the other hand, the widely used long-tube method provides results that are neither straightforward, nor fully understood. This study performed on a 0.09 mm axially drilled single-hole nozzle is part of the Engine Combustion Network (ECN) and aims at analyzing these features from an acoustic point of view to separate their impact on the real injection process and on the results recorded by the experimental devices. Several tests have been carried out for this study including rate of injection and momentum, X-ray phase-contrast of the injector and needle motion or injector displacement. The acoustic analysis revealed that these fluctuations found their origin in the sac of the injector and that they were the results of an interaction between the fluid in the chamber (generally gases) and the liquid fuel to be injected. It has been observed that the relatively high oscillations recorded by the long-tube method were mainly caused by a displacement of the injector itself while injecting. In addition, the results showed that these acoustic features also appear on the momentum flux of the spray which means that the real rate of injection should present such behavior.

Effect of Injection Rate Shaping Over Diesel Spray Development in Non Reacting Evaporative Conditions

A prototype Diesel common rail direct-acting piezoelectric injector has been used to study the influence of fuel injection rate shaping on spray behavior (liquid phase penetration) under evaporative and non-reacting conditions. This state of the art injector allows a fully flexible control of the nozzle needle, enabling various fuel injection rates typologies under a wide range of test conditions. The tests have been performed employing a novel continuous flow test chamber that allows an accurate control on a wide range of thermodynamic test conditions (up to 1000 K and 15 MPa). The temporal evolution of the spray has been studied recording movies of the injection event with a fast camera (25 kfps) by means of the Mie scattering visualization technique. The analysis of the results showed a strong influence of needle position on the behavior of the liquid length. The needle position controls the effective pressure upstream of the nozzle holes. Higher needle lift is equivalent to higher effective pressures. According to the free-jet theory, the stabilized liquid-length depends mainly on effective diameter, spray cone-angle and fuel/air properties and does not depend on injection velocity. Therefore, higher injection pressures gives slightly lower liquid length due to small change in the spray cone-angle. However, partial needle lifts has an opposite effect: lower effective pressure upstream of the nozzle holes shows a dramatic increase on the spray cone-angle, reducing the liquid length. This behavior could be explained mainly due to the fact that the flow direction upstream of the nozzle holes is affecting the area coefficient, or in other words, the effective diameter of the holes.