Temperature Control of Metal Strip during High-Rate Vacuum Coating

Author(s):  
Jens-Peter Heinss ◽  
◽  
P. Lang ◽  
P. Ruppelt ◽  
◽  
...  
2016 ◽  
Vol 290 ◽  
pp. 39-42 ◽  
Author(s):  
Jens-Peter Heinß ◽  
Peter Lang ◽  
Patrick Ruppelt

2012 ◽  
Vol 504-506 ◽  
pp. 587-592 ◽  
Author(s):  
Marion Merklein ◽  
Tommaso Stellin ◽  
Ulf Engel

A high rate of production of complex microparts is increasingly required by fields like electronics and micromechanics. Handling is one of the main problems, limiting those forming processes of small metal components consisting of multiple forming stages. A forming chain in which a metal strip acts both as raw material and support of the workpiece through the different stages of the process, is seen as a solution that radically simplifies the positioning of microparts. Each workpiece stays connected to the strip through all the forming steps, being separated just at the end of the process chain. In this work, a tooling system for the bulk forming from copper strips has been set up and employed in a full forward extrusion process of a micro-billet. The same die, with a diameter of 1 mm, has been used with three different strip thicknesses (1, 2 and 3 mm) and three different material conditions. The use of thinner and hard-as-rolled strips has resulted in achieving a higher ratio of the billet length to strip thickness.


Author(s):  
Ali M Y Al-Sakkaf ◽  
Elizabeth Redmond ◽  
Charles Brennan ◽  
Ravi Gooneratne

New Zealand (NZ) has a high rate of reported campylobacteriosis cases. Cross-contamination in home kitchens during poultry handling is considered to be the main factor in campylobacteriosis transmission. The main aim of this study was to measure NZ consumers' food safety awareness and self-reported food safety practices associated with handling raw poultry. This study will contribute to the existing knowledge to explain the reasons behind the increase of campylobacteriosis incidents. Findings can help inform future consumer education campaigns to help reduce the incidence of campylobacteriosis in NZ. A cross-sectional survey comprised of 31 multiple-choice questions was designed, piloted, and utilized to collect information about the last time consumers purchased and prepared raw poultry at home. A street-intercept survey in public places, such as supermarkets in the Canterbury region, was used to recruit respondents for this study. A descriptive and inferential data analysis was performed, including a one-way ANOVA test used to compare the mean scored responses between the respondents among different socio-demographics. Overall, 301 valid responses were obtained. Scores, representing reported safe food safety practices ranged between 2 and 19 (maximum 21) with a mean score of 9.83 (standard deviation 3.50 with a standard error of 0.20). There was some variation of correctly answered questions by the respondents for food hygiene (25%), cross-contamination prevention (55%), temperature control and storage practices (49%), and food safety (52%). Approximately 30% of the respondents reported symptoms of a foodborne disease experience once to four times during the past 12 months. The study identified low adherence to current recommended food safety practices, including safe food storage and temperature control. The findings can be used to inform a communication campaign regarding food safety needs to be designed urgently in NZ to reduce the rate of campylobacteriosis.


2010 ◽  
pp. NA-NA
Author(s):  
Yasushi Sobajima ◽  
Takuya Higuchi ◽  
Jakapan Chantana ◽  
Toshihiko Toyama ◽  
Chitose Sada ◽  
...  

Author(s):  
L. E. Murr ◽  
G. Wong

Palladium single-crystal films have been prepared by Matthews in ultra-high vacuum by evaporation onto (001) NaCl substrates cleaved in-situ, and maintained at ∼ 350° C. Murr has also produced large-grained and single-crystal Pd films by high-rate evaporation onto (001) NaCl air-cleaved substrates at 350°C. In the present work, very large (∼ 3cm2), continuous single-crystal films of Pd have been prepared by flash evaporation onto air-cleaved (001) NaCl substrates at temperatures at or below 250°C. Evaporation rates estimated to be ≧ 2000 Å/sec, were obtained by effectively short-circuiting 1 mil tungsten evaporation boats in a self-regulating system which maintained an optimum load current of approximately 90 amperes; corresponding to a current density through the boat of ∼ 4 × 104 amperes/cm2.


Author(s):  
P.R. Swann ◽  
A.E. Lloyd

Figure 1 shows the design of a specimen stage used for the in situ observation of phase transformations in the temperature range between ambient and −160°C. The design has the following features a high degree of specimen stability during tilting linear tilt actuation about two orthogonal axes for accurate control of tilt angle read-out high angle tilt range for stereo work and habit plane determination simple, robust construction temperature control of better than ±0.5°C minimum thermal drift and transmission of vibration from the cooling system.


Author(s):  
A. Elgsaeter ◽  
T. Espevik ◽  
G. Kopstad

The importance of a high rate of temperature decrease (“rapid freezing”) when freezing specimens for freeze-etching has long been recognized1. The two basic methods for achieving rapid freezing are: 1) dropping the specimen onto a metal surface at low temperature, 2) bringing the specimen instantaneously into thermal contact with a liquid at low temperature and subsequently maintaining a high relative velocity between the liquid and the specimen. Over the last couple of years the first method has received strong renewed interest, particularily as the result of a series of important studies by Heuser and coworkers 2,3. In this paper we will compare these two freezing methods theoretically and experimentally.


Sign in / Sign up

Export Citation Format

Share Document