Effect of Particle Packing and Fly Ash on Performance of Ordinary Portland Cement/Anhydrite-Activated Ground-Granulated Blast-Furnace Slag

2017 ◽  
Vol 114 (4) ◽  
Author(s):  
Tristana Y. Duvallet ◽  
Laurent Frouin ◽  
Thomas L. Robl ◽  
Anne E. Oberlink ◽  
Robert B. Jewell
Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3448
Author(s):  
Chenhui Jiang ◽  
Aiying Wang ◽  
Xufan Bao ◽  
Zefeng Chen ◽  
Tongyuan Ni ◽  
...  

This paper presents an experimental investigation on geopolymer coatings (GPC) in terms of surface protection of civil structures. The GPC mixtures were prepared with a quadruple precursor simultaneously containing fly ash (FA), ground granulated blast-furnace slag (GBFS), metakaolin (MK), and Portland cement (OPC). Setting time, compressive along with adhesive strength and permeability, were tested and interpreted from a perspective of potential applications. The preferred GPC with favorable setting time (not shorter than 120 min) and desirable compressive strength (not lower than 35 MPa) was selected from 85 mixture formulations. The results indicate that balancing strength and setting behavior is viable with the aid of the multi-componential precursor and the mixture design based on total molar ratios of key oxides or chemical elements. Adhesive strength of the optimized GPC mixtures was ranged from 1.5 to 3.4 MPa. The induced charge passed based on a rapid test of coated concrete specimens with the preferred GPC was 30% lower than that of the uncoated ones. Setting time of GPC was positively correlated with η[Si/(Na+Al)]. An abrupt increase of setting time occurred when the molar ratio was greater than 1.1. Compressive strength of GPC was positively affected by mass contents of ground granulated blast furnace slag, metakaolin and ordinary Portland cement, and was negatively affected by mass content of fly ash, respectively. Sustained seawater immersion impaired the strength of GPC to a negligible extent. Overall, GPC potentially serves a double purpose of satisfying the usage requirements and achieving a cleaner future.


2010 ◽  
Vol 158 ◽  
pp. 1-11 ◽  
Author(s):  
Zi Qiao Jin ◽  
Xian Jun Lu ◽  
Shu Gang Hu

In order to stimulate the potential cementitious property of granulated blast furnace slag (GBFS), the ground GBFS sample (Wei Fang Iron and Steel Corporation, China) was activated by lime and gypsum under different dosages. The results showed that lime is an effective activator for the slag, and the optimum dosage of lime is about 10% (w/w) of the slag. At the optimum dosage of lime, the 28 days compressive strength of the lime-slag paste is higher than that of 32.5 ordinary Portland cement (OPC). But, the early age strength (3 and 7 days compressive strength) of the lime-slag paste is lower than that of the OPC. Addition of gypsum can effectively improve the early age strength of the lime-slag paste. At the ratio of gypsum:lime:slag of 8.2:9.2:82.6 (w/w), both the early and long-term compressive strengths of the gypsum-lime-slag paste are higher than that of the OPC. According to XRD, TG-DTA and SEM detections of the hydration products of the lime-slag paste, the gypsum-lime-slag paste and the OPC paste, it reveals that the hydration process of the GBFS-based cementitious material is different from the ordinary Portland cement and the presence of ettringite (AFt) contributes to the early age strength of the pastes. The major hydration product of the OPC paste (<7 days) were measured as ettringite (AFt), but the AFt phase was not detected in the hydration product of the lime-slag paste and the major hydration product of the lime-slag paste was determined as amorphous CSH gel. However, AFt was detected in the hydration products of the gypsum-lime-slag paste in the early stages of hydration, and the formation of AFt is favorable for the early strength improvement of the material.


2017 ◽  
Vol 259 ◽  
pp. 30-34 ◽  
Author(s):  
Vlastimil Bílek ◽  
Filip Khestl ◽  
Pavel Mec

Hybrid cements represent a relatively new type of binders which combines some of the advantages of Ordinary Portland Cement and an application of mineral admixtures and alkali activation. Hybrid cements form then blends containing a low portion of OPC and a high proportion of mineral additions (such as blast furnace flag, fly ash, metakaoline, ...). This paper discusses the properties of mortars based on carbonate based activators. Mixtures composed from Ordinary Portland Cement, ground granulated blast furnace slag, fly ash and mechanically pre-activated fly ash were optimised with the target to achieve sufficient compressive strength. The influence of ratios between powder compounds, the dosage of activator and water to binder ratios are presented.


2019 ◽  
Vol 25 (3) ◽  
pp. 340-347
Author(s):  
Ting WANG ◽  
Xiaojian GAO ◽  
Jian WANG

As a byproduct of phosphoric acid industry, phosphogypsum has many environmental problems. In order to recycle phosphogypsum to manufacture lightweight building materials, cementitious additives including fly ash, ground granulate blast-furnace slag and Portland cement were added to improve strength and water-resistance and different volume of foam was added to reduce the bulk density. The results show that hydrated lime can improve mechanical strength and water resistance of PG paste and the optimal dosage of hydrated lime is 6 %. Higher addition of fly ash or ground granulated blast-furnace slag improves the fluidity and delays the setting time of PG paste. The addition of 10 ~ 20 % fly ash results in a little reducing influence and 10 % ground granulated blast-furnace slag leads to an increase of 20.7 % for 28 days compressive strength of hardened PG specimen. The higher addition of Portland cement results in the better mechanical strength and water resistance of PG specimens. The 28day compressive and flexural strength reaches 25.9 MPa and 8.9 MPa respectively for the 25 % Portland cement mixture. PG based lightweight building materials can prepared by the addition of 60 % volume of air foam, with compressive strength of 1.7 MPa, bulk density of 521.7 kg/m3 and thermal conductivity of 0.0724 W/(m·K). DOI: http://dx.doi.org/10.5755/j01.ms.25.3.19910


2020 ◽  
Vol 12 (14) ◽  
pp. 5783 ◽  
Author(s):  
Rosa Abnelia Rivera ◽  
Miguel Ángel Sanjuán ◽  
Domingo Alfonso Martín

Granulated blast-furnace slag (GBFS) and coal fly ash (CFA) are two well-known constituents in Portland cements. Ternary Portland cements (GBFS-CFA-K) provide environmental advantages by reducing Portland cement clinker (K) production and, therefore, promote lower CO2 emissions. Nevertheless, both of them cause a delay in the compressive strength gain. Given that, the early compressive strength for both constituents is low, but they improve the compressive strength at medium and later ages as consequence of the pozzolanic reaction. In this paper, a full factorial design with two levels was developed for the mortar compressive strength estimation at 2, 7 and 28 days. Mortar prisms made with 25% and 40% of granulated blast-furnace slag (GBFS) and/or coal fly ash (CFA) were tested. The effects of the interaction between GBFS and CFA on the compressive strength development of ternary Portland cement mortars were reported. Results show that the contribution of both cement constituents to the ternary mortar mix reduces the compressive strength for all the tested ages. Nevertheless, the finer the GBFS, the better ternary cement performance was achieved, showing that the synergistic effect is more effective when the finer GBFS is used, probably due to a more adequate particle size distribution. Finally, a relationship between compressive strength, fineness, GBFS content and CFA content was found for each age.


Sign in / Sign up

Export Citation Format

Share Document