scholarly journals Pengaruh mikroplastik polietilen dan oxo-degradable (Oxium) pada pertumbuhan Mikroalga Tetraselmis Chuii

2021 ◽  
Vol 19 (2) ◽  
pp. 211-218
Author(s):  
Adian Khoironi ◽  
Khoirul Huda ◽  
Imron Hambyah ◽  
Inggar Dianratri
Keyword(s):  
Growth Rate ◽  
Optical Density ◽  
Aquatic Environment ◽  
High Density Polyethylene ◽  
Negative Impact ◽  
Environmentally Friendly ◽  
High Density ◽  
Density Measurements ◽  
Tetraselmis Chuii ◽  
Plastic Bags

Salah satu cara yang digunakan di Indonesia dalam menanggulangi berlimpahnya jumlah sampah plastik di lingkungan perairan adalah dengan menggantikan kantong plastik berbahan polimer polietilen (PE) dengan plastik oxodegradable yang disebut oxium. Penelitian ini dilakukan dengan tujuan untuk melihat pengaruh mikroplastik polietilen jenis HDPE (High Density Polyethylene) dengan plastic oxodegradable oxium. Penelitian dilakukan dengan menggunakan mikroalga Tetraselmis chuii sebagai mikroorganisme yang akan mendapat perlakuan mikroplastik dengan konsentrasi yang berbeda. Dari Hasil pengukuran optical density untuk menentukan laju pertumbuhan mikroalga Tetraselmis Chuii menunjukkan bahwa laju pertumbuhan Tetraselmis  dengan perlakuan mikroplastik polietilen mengalami penurunan yang signifikan dibandingkan dengan mikroplastik oxium. Konsentrasi mikroplastik ikut berperan dalam menentukan laju pertumbuhan Tetraselmis chuii di mana pada perlakuan mikroplastik oxium terjadi penurunan hingga 37,66% pada konsentrasi mikroplastik 300mg/500mL dan 81,70% pada perlakuan mikroplastik polietilen dengan konsentrasi 200mg/500mL. Mikroplastik polietilen dan oxium memberikan dampak negatif pada organisme tingkat rendah disebabkan oleh kemampuannya dalam melepas bahan aditif yang bersifat toksik sehingga diperlukan solusi yang lebih baik untuk menggantikan fungsi plastik dengan bahan yang lebih ramah bagi lingkungan hidup.  ABSTRACTOne of the methods used in Indonesia in tackling the abundance of plastic waste in the aquatic environment is to replace plastic bags made of polyethylene (PE) polymer with oxodegradable plastic called oxium. This research was conducted with the aim of examining the effect of HDPE (High Density Polyethylene) microplastic polyethylene with oxodegradable oxium plastic. The research was conducted using the microalgae Tetraselmis chuii as microorganisms that will receive microplastic treatment with different concentrations. From the results of optical density measurements to determine the growth rate of Tetraselmis chuii microalgae, it was shown that the growth rate of Tetraselmis with polyethylene microplastics treatment decreased significantly compared to oxium microplastics. The concentration of microplastics played a role in determining the growth rate of Tetraselmis chuii where in the oxium microplastic treatment there was a decrease of up to 37.66% at the microplastic concentration of 300mg/500mL and 81.70% at the polyethylene microplastic treatment with a concentration of 200mg/500mL. Polyethylene and oxyum microplastics have a negative impact on low-level organisms due to their ability to release toxic additives so that better solutions are needed to replace the function of plastics with materials that are more environmentally friendly.

Studi Karakteristik Stabilitas dan Konstruksi Kapal Berbahan High Density Polyethylene (HDPE)

2021 ◽  
Vol 12 (2) ◽  
pp. 315-323
Author(s):  
Muammar Kadhafi ◽  
◽  
Sunardi Sunardi ◽  
Agus Triono ◽  
Wahida Kartika Sari ◽  
...  
Keyword(s):  
High Density Polyethylene ◽  
Environmentally Friendly ◽  
High Density ◽  
International Maritime Organization ◽  
Loading Conditions ◽  
Marine Tourism ◽  
Design Software ◽  
The Stability ◽  
Naval Architect ◽  
Main Material

The development of fishing and marine tourism requires the support of naval architecture, especially in small boat. The use of wood as the main material for shipbuilding has recently become a problem considering the decreasing availability of wood, while the use of fiber is classified as less environmentally friendly because it uses chemical resin and difficult to repair when it breaks and cannot be recycled. The aim of this research is to design the High-Density Polyethylene (HDPE) boat. The design was carried out by using naval architect design software. The stability of boat was calculated by using three loading conditions such as when leaving the port, in the sea and when returning to the port. The International Maritime Organization (IMO) safety criteria was using to evaluation of boat stability where the three loading conditions have met the IMO standard. The construction of HDPE boat was carried out by using DNV rules.

Composition and Surface Topography Effects on Apatite-Forming Ability of Ceramic-Polymer Composites

2003 ◽  
Vol 774 ◽  
Author(s):  
Susan M. Rea ◽  
Serena M. Best ◽  
William Bonfield
Keyword(s):  
Surface Topography ◽  
High Density Polyethylene ◽  
High Density ◽  
Apatite Layer ◽  
Biologically Active ◽  
Human Blood Plasma ◽  
Apatite Formation ◽  
Polyethylene Matrix ◽  
Composite Surface ◽  
X Ray

AbstractHAPEXTM (40 vol% hydroxyapatite in a high-density polyethylene matrix) and AWPEX (40 vol% apatite-wollastonite glass ceramic in a high density polyethylene matrix) are composites designed to provide bioactivity and to match the mechanical properties of human cortical bone. HAPEXTM has had clinical success in middle ear and orbital implants, and there is great potential for further orthopaedic applications of these materials. However, more detailed in vitro investigations must be performed to better understand the biological interactions of the composites and so the bioactivity of each material was assessed in this study. Specifically, the effects of controlled surface topography and ceramic filler composition on apatite layer formation in acellular simulated body fluid (SBF) with ion concentration similar to those of human blood plasma were examined. Samples were prepared as 1 cm × 1 cm × 1 mm tiles with polished, roughened, or parallel-grooved surface finishes, and were incubated in 20 ml of SBF at 36.5 °C for 1, 3, 7, or 14 days. The formation of a biologically active apatite layer on the composite surface after immersion was demonstrated by thin-film x-ray diffraction (TF-XRD), environmental scanning electron microscopy (ESEM) imaging and energy dispersive x-ray (EDX) analysis. Variations in sample weight and solution pH over the period of incubation were also recorded. Significant differences were found between the two materials tested, with greater bioactivity in AWPEX than HAPEXTM overall. Results also indicate that within each material the surface topography is highly important, with rougher samples correlated to earlier apatite formation.

Sign in / Sign up

Export Citation Format

Share Document