scholarly journals Optimasi Desain Bucket Tooth Excavator Jenis Verona PC200 Menggunakan Optimasi Topologi dan Metode Elemen Hingga

ROTASI ◽  
2019 ◽  
Vol 21 (4) ◽  
pp. 237
Author(s):  
Sumar Hadi Suryo ◽  
Rachmat Suryadi Sastra ◽  
Muchammad Muchammad
Keyword(s):  
Von Mises

Excavator merupakan alat berat yang biasanya digunakan untuk menggali tanah, membelah batu, membongkar jalan atau merobohkan bangunan. Salah satu komponen yang berperan dalam fungsi tersebut adalah bucket tooth. Pada penelitian ini membahas tentang perancangan optimasi bucket tooth yang ada di pasaran untuk menghasilkan desain yang lebih ringan tetapi tetap mempertahankan kekuatannya, bucket tooth tersebut adalah Verona PC200. Proses optimasi pada bucket tooth menerapkan konsep optimasi topologi. Metode yang dilakukan meliputi penentuan jenis material yang dipakai dengan berbagai pengujian yaitu uji komposisi, uji mikrografi dan uji kekerasan. Kemudian dilakukan analisis linear statik menggunakan metode elemen hingga untuk melihat tegangan maksimum yang terjadi pada bucket tooth, besarnya nilai tegangan Von-mises sebesar 403,81 MPa. Selanjutnya dilakukan optimasi topologi dengan memilih beberapa variasi area desain yang menghasilkan reduksi massa dalam variasi pertama sebesar 0,72 kg dan pada variasi kedua 1,49 kg. Reduksi massa tersebut menyebabkan perubahan tegangan yang terjadi pada bucket tooth menjadi 451,8 MPa pada variasi pertama, dan 458,6 MPa pada variasi kedua, namun tegangan tersebut masih dalam kondisi aman.

Which human qualities can economic liberalism be based on?

2015 ◽  
pp. 5-24 ◽  
Author(s):  
V. Avtonomov
Keyword(s):  
Economic Policy ◽  
Human Values ◽  
High Rank ◽  
Economic Liberalism ◽  
Von Mises ◽  
Liberal Policy

The article asks which human qualities can serve as the base for a liberal economic policy. The author is looking for an answer to this question in the classical works of economic liberalism - in the books by F. Bastiat, L. von Mises, F. von Hayek, W. Eucken, and M. Friedman. The two main qualities can be summarized as follows: the relatively high rank of freedom among human values and rational utilitarian calculus. It is assumed that in those countries where the both human prerequisites are present the liberal policy (for instance, liberal reforms) can be self-supportive and may have good results. On the contrary, if the first prerequisite is missing and a liberal policy can be based only on rational calculus, the “paternalistic” liberalism prevails and chances for success are much smaller.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

The Influence of Loading Position in A Priori High Stress Detection using Mode Superposition

2020 ◽  
Vol 1 (1) ◽  
pp. 93-102
Author(s):  
Carsten Strzalka ◽  
◽  
Manfred Zehn ◽  
Keyword(s):  
Finite Element ◽  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
A Priori ◽  
High Stress ◽  
Von Mises Stress ◽  
Detailed Knowledge ◽  
Variable Loading ◽  
Numerical Effort ◽  
Von Mises

For the analysis of structural components, the finite element method (FEM) has become the most widely applied tool for numerical stress- and subsequent durability analyses. In industrial application advanced FE-models result in high numbers of degrees of freedom, making dynamic analyses time-consuming and expensive. As detailed finite element models are necessary for accurate stress results, the resulting data and connected numerical effort from dynamic stress analysis can be high. For the reduction of that effort, sophisticated methods have been developed to limit numerical calculations and processing of data to only small fractions of the global model. Therefore, detailed knowledge of the position of a component’s highly stressed areas is of great advantage for any present or subsequent analysis steps. In this paper an efficient method for the a priori detection of highly stressed areas of force-excited components is presented, based on modal stress superposition. As the component’s dynamic response and corresponding stress is always a function of its excitation, special attention is paid to the influence of the loading position. Based on the frequency domain solution of the modally decoupled equations of motion, a coefficient for a priori weighted superposition of modal von Mises stress fields is developed and validated on a simply supported cantilever beam structure with variable loading positions. The proposed approach is then applied to a simplified industrial model of a twist beam rear axle.

MODELING OF THE STRESS-STRAIN STATE OF A TRANSPORT TUNNEL UNDER LOAD AS A MEASURE TO REDUCE OPERATIONAL RISKS TO TRANSPORTATION FACILITIES

2020 ◽  
Vol 3 (8) ◽  
pp. 28-34
Author(s):  
N. V. IVANITSKAYA ◽  
◽  
A. K. BAYBULOV ◽  
M. V. SAFRONCHUK ◽  
◽  
...  
Keyword(s):  
Strain State ◽  
Moving Load ◽  
Element Model ◽  
Transport Infrastructure ◽  
Design Stage ◽  
Surface Load ◽  
Stress Strain ◽  
Stress Strain State ◽  
Operational Risks ◽  
Von Mises

In many countries economic policy has been paying increasing attention to the modernization and development of transport infrastructure as a measure of macroeconomic stimulation. Tunnels as an important component of transport infrastructure save a lot of logistical costs. It stimulates increasing freight and passenger traffic as well as the risks of the consequences of unforeseen overloads. The objective of the paper is to suggest the way to reduce operational risks of unforeseen moving load by modeling of the stress-strain state of a transport tunnel under growing load for different conditions and geophysical parameters. The article presents the results of a study of the stress-strain state (SSS) of a transport tunnel exposed to a mobile surface load. Numerical experiments carried out in the ANSYS software package made it possible to obtain diagrams showing the distribution of equivalent stresses (von Mises – stresses) according to the finite element model of the tunnel. The research results give grounds to assert that from external factors the stress state of the tunnel is mainly influenced by the distance to the moving load. The results obtained make it possible to predict in advance the parameters of the stress-strain state in the near-contour area of the tunnel and use the results in the subsequent design of underground facilities, as well as to increase their reliability and operational safety. This investigation gives an opportunity not only to reduce operational risks at the design stage, but to choose an optimal balance between investigation costs and benefits of safety usage period prolongation.

Stress Field Around a Large Opening in a Pressure Vessel During a Major Repair

2009 ◽  
Author(s):  
Erik Garrido ◽  
Euro Casanova
Keyword(s):  
Pressure Vessel ◽  
New Technologies ◽  
Mechanical Design ◽  
General Purpose ◽  
Pressure Vessels ◽  
Mechanical Equipment ◽  
Stress Distributions ◽  
Large Opening ◽  
Von Mises ◽  
Case Basis

It is a regular practice in the oil industry to modify mechanical equipment to incorporate new technologies and to optimize production. In the case of pressure vessels, it is occasionally required to cut large openings in their walls in order to have access to the interior part of the equipment for executing modifications. This cutting process produces temporary loads, which were obviously not considered in the original mechanical design. Up to now, there is not a general purpose specification for approaching the assessments of stress levels once a large opening in a vertical pressure vessel has been made. Therefore stress distributions around large openings are analyzed on a case-by-case basis without a reference scheme. This work studies the distribution of the von Mises equivalent stresses around a large opening in FCC Regenerators during internal cyclone replacement, which is a frequently required practice for this kind of equipment. A finite element parametric model was developed in ANSYS, and both numerical results and illustrating figures are presented.

An extension of the von mises distribution

1982 ◽  
Vol 11 (15) ◽  
pp. 1695-1706 ◽  
Author(s):  
E.A. Yfantis ◽  
L.E. Borgman
Keyword(s):  
Von Mises Distribution ◽  
Von Mises
Sign in / Sign up

Export Citation Format

Share Document