scholarly journals Analysis, Design and Experimental Validation of Modified Simple Soft Switching DC-DC Boost Converter

2015 ◽  
Vol 16 (4) ◽  
pp. 331-337 ◽  
Author(s):  
S. Raghavendran ◽  
B. Chitti Babu ◽  
Luigi Piegari
Keyword(s):  
Theoretical Analysis ◽  
Experimental Validation ◽  
Soft Switching ◽  
Zero Voltage Switching ◽  
Switching Losses ◽  
Zero Current Switching ◽  
Zero Current ◽  
Analysis Design ◽  
Zero Voltage ◽  
Voltage Switching

Abstract This paper investigates a modified simple soft switching dc-dc converter for low power applications. This simple topology uses an auxiliary switch, an inductor and a capacitor to operate the converter without switching losses. The efficiency of the converter is improved by transferring the energy that would be dissipated during the switching to the load. The main switch turns-on with zero current switching (ZCS) and turns-off with zero voltage switching (ZVS), while the auxiliary switch turns-on and turns-off with zero voltage switching (ZVS). The detailed theoretical analysis and the design equations are described. In addition to that, the analysis of proposed converter is demonstrated by both simulation and experimental results for effectiveness of the study.

scholarly journals Soft-Switching High Gain Step-Up DC/DC Converter without Auxiliary Switches

2019 ◽  
Vol 8 (12S) ◽  
pp. 633-636
Keyword(s):  
Theoretical Analysis ◽  
Power Flow ◽  
High Efficiency ◽  
Input Voltage ◽  
High Gain ◽  
Soft Switching ◽  
Zero Voltage Switching ◽  
Auxiliary Cell ◽  
Zero Voltage ◽  
Voltage Switching

This manuscript presents a novel high gain, high efficiency Soft-switching high step-up DC/DC converter for battery-operated vehicles. The high step-up converter can transfer the power flow from the small voltage to high voltage. The conventional two input inductor hard switched non-isolated DC-DC converter improved with an additional auxiliary cell to attain the Zero voltage switching, due to obtaining the softswitching the efficiency may improve and reduces the stress across the main switches. The isolated converters are used as a transformer to attain high gain, whereas in the proposed converter obtains the high gain without a transformer and contains the high efficiency in the step-up mode of operation. The main aim of the converter is to attain the Zero voltage switching without using any additional auxiliary switches. In this paper, the input voltage applied as 30V, and the obtained output voltage is fifteen times to the applied voltage, which is 450V and the output power 850W. This paper mainly presents the theoretical analysis of converter operation and the evaluation of the simulation results validated with the theoretical analysis.

scholarly journals A Novel Three-Phase Six-Switch PFC Rectifier with Zero-Voltage-Switching and Zero-Current-Switching Features

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 1119 ◽  
Author(s):  
Chun-Wei Lin ◽  
Chang-Yi Peng ◽  
Huang-Jen Chiu
Keyword(s):  
Switching Loss ◽  
Modeling And Analysis ◽  
Zero Voltage Switching ◽  
Current Switching ◽  
Zero Current Switching ◽  
Zero Current ◽  
Three Phase ◽  
The One ◽  
Zero Voltage ◽  
Voltage Switching

A novel three-phase power-factor-correction (PFC) rectifier with zero-voltage-switching (ZVS) in six main switches and zero-current-switching (ZCS) in the auxiliary switch is proposed, analyzed, and experimentally verified. The main feature of the proposed auxiliary circuit is used to reduce the switching loss when the six main switches are turned on and the one auxiliary switch is turned off. In this paper, a detailed operating analysis of the proposed circuit is given. Modeling and analysis are verified by experimental results based on a three-phase 7 kW rectifier. The soft-switched PFC rectifier shows an improvement in efficiency of 2.25% compared to its hard-switched counterpart at 220 V under full load.

scholarly journals An Interleaved DC/DC Converter with Soft-switching Characteristic and high Step-up Ratio

2020 ◽  
Vol 10 (6) ◽  
pp. 2167
Author(s):  
Yong-Nong Chang ◽  
Hung-Liang Cheng ◽  
Hau-Chen Yen ◽  
Chien-Hsuan Chang ◽  
Wei-Di Huang
Keyword(s):  
Conversion Efficiency ◽  
Operation Mode ◽  
Soft Switching ◽  
Switching Characteristic ◽  
Boost Converters ◽  
Zero Voltage Switching ◽  
Zero Current Switching ◽  
Zero Current ◽  
Current Ripples ◽  
Zero Voltage

This study presents a dc/dc converter featuring soft-switching characteristic, high conversion efficiency, and high step-up ratio. The proposed circuit is composed of two parallel-connected boost converters. Only one coupled inductor is used to replace inductors of the boost converters which are interleaved operated at discontinuous-conduction mode (DCM). The current ripples at the input and the output terminals are reduced due to the interleaved operation. By freewheeling the current of the coupled inductor to discharge the stored electric charges in the parasitic capacitors of the active switches, both active switches can fulfill zero-voltage switching on (ZVS). Owing to DCM operation, the freewheeling diodes can fulfill zero-current switching off (ZCS). Therefore, the power conversion efficiency is improved. The operation principle for each operation mode is analyzed in detail and design equations for the component parameters are provided in this report. Finally, a prototype 200 W 48–400 V converter was implemented and measured to demonstrate the effectiveness of the proposed circuit.

A ZVS/ZCS SOLUTION TO CROSSOVER DISTORTION IN BOOST PFC RECTIFIER

2005 ◽  
Vol 14 (06) ◽  
pp. 1045-1062
Author(s):  
MUHAMMAD MANSOOR KHAN ◽  
ZHI-MING WU ◽  
JUNMIN PAN
Keyword(s):  
Energy Conservation ◽  
Prototype System ◽  
Zero Voltage Switching ◽  
Current Switching ◽  
The Past ◽  
Zero Current Switching ◽  
Zero Current ◽  
Boost Rectifier ◽  
Zero Voltage ◽  
Voltage Switching

Several ZVS/ZCS (zero voltage switching/zero current switching) snubbers have been proposed in the past to minimize the losses and EMI in boost PFC. In these topologies, the commutation energies are reflected to the load or source to achieve energy conservation. However, this energy can also be utilized in a way to further improve the performance of the PFC and this paper is a first step in this direction. Here, we will propose a new topology to minimize the crossover distortion in boost rectifier. The main characteristic of the proposed topology besides ZCS/ZVS switching is that it also improves the crossover distortion. A prototype system was built and tested to verify the proposed topology.

Sign in / Sign up

Export Citation Format

Share Document