Retained Tensile Properties and Performance of an Oxide-Matrix Continuous-Fiber Ceramic Composite After Elevated-Temperature Exposure in Ambient Air

Author(s):  
KL Munson ◽  
MG Jenkins
Materials ◽  
2019 ◽  
Vol 12 (12) ◽  
pp. 1995 ◽  
Author(s):  
Yongxin Yang ◽  
Yanju Jiang ◽  
Hongjun Liang ◽  
Xiaosan Yin ◽  
Yue Huang

Elevated temperature exposure has a negative effect on the performance of the matrix resin in Carbon Fiber Reinforced Plastics (CFRP) plates, whereas limited quantitative research focuses on the deteriorations. Therefore, 30 CFRP specimens were designed and tested under elevated temperatures (10, 30, 50, 70, and 90 °C) to explore the degradations in tensile properties. The effect of temperature on the failure mode, stress-strain curve, tensile strength, elastic modulus and elongation of CFRP plates were investigated. The results showed that elevated temperature exposure significantly changed the failure characteristics. When the exposed temperature increased from 10 °C to 90 °C, the failure mode changed from the global factures in the whole CFRP plate to the successive fractures in carbon fibers. Moreover, with temperatures increasing, tensile strength and elongation of CFRP plates decreases gradually while the elastic modulus shows negligible change. Finally, the results of One-Way Analysis of Variance (ANOVA) show that the degradation of the tensile strength of CFRP plates was due to the impact of elevated temperature exposure, rather than the test error.


2005 ◽  
Vol 55 (12) ◽  
pp. 673-677 ◽  
Author(s):  
Kousuke ONO ◽  
Tomofumi TANAKA ◽  
Yoshio ITSUMI ◽  
Hideto OYAMA

Alloy Digest ◽  
1998 ◽  
Vol 47 (12) ◽  

Abstract MO-RE 40MA is a fully austenitic heat-resistant alloy for elevated temperature applications. The alloy is microalloyed for creep strength and oxidation resistance. This datasheet provides information on composition, physical properties, and tensile properties as well as creep. It also includes information on high temperature performance. Filing Code: Ni-548. Producer or source: Duraloy Technologies Inc.


Alloy Digest ◽  
1987 ◽  
Vol 36 (12) ◽  

Abstract UHB QRO 80 MICRODIZED is a chromium-molybdenum-vanadium tool steel with improved performance for tooling used at elevated temperature as in forging, extrusion and die casting. It is electro-slag refined. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on high temperature performance as well as forming, heat treating, machining, and joining. Filing Code: TS-486. Producer or source: Uddeholm Aktiebolag.


2021 ◽  
Vol 109 (4) ◽  
pp. 243-260 ◽  
Author(s):  
Yves Wittwer ◽  
Robert Eichler ◽  
Dominik Herrmann ◽  
Andreas Türler

Abstract A new setup named Fast On-line Reaction Apparatus (FORA) is presented which allows for the efficient investigation and optimization of metal carbonyl complex (MCC) formation reactions under various reaction conditions. The setup contains a 252Cf-source producing short-lived Mo, Tc, Ru and Rh isotopes at a rate of a few atoms per second by its 3% spontaneous fission decay branch. Those atoms are transformed within FORA in-situ into volatile metal carbonyl complexes (MCCs) by using CO-containing carrier gases. Here, the design, operation and performance of FORA is discussed, revealing it as a suitable setup for performing single-atom chemistry studies. The influence of various gas-additives, such as CO2, CH4, H2, Ar, O2, H2O and ambient air, on the formation and transport of MCCs was investigated. O2, H2O and air were found to harm the formation and transport of MCCs in FORA, with H2O being the most severe. An exception is Tc, for which about 130 ppmv of H2O caused an increased production and transport of volatile compounds. The other gas-additives were not influencing the formation and transport efficiency of MCCs. Using an older setup called Miss Piggy based on a similar working principle as FORA, it was additionally investigated if gas-additives are mostly affecting the formation or only the transport stability of MCCs. It was found that mostly formation is impacted, as MCCs appear to be much less sensitive to reacting with gas-additives in comparison to the bare Mo, Tc, Ru and Rh atoms.


Sign in / Sign up

Export Citation Format

Share Document