Estimation method of residual stress and plastic strain in austenitic stainless steel by single indentation test

2014 ◽  
pp. 555-559
Author(s):  
R. Kusano ◽  
T. Hiyoshi ◽  
A. Yonezu
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Plastic Strain ◽  
Estimation Method ◽  
Indentation Test

Residual Microstress of Austenitic Stainless Steel Due to Tensile Deformation

2010 ◽  
Vol 652 ◽  
pp. 7-12 ◽  
Author(s):  
Kenji Suzuki ◽  
Takahisa Shobu
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Plastic Strain ◽  
Tensile Deformation ◽  
Annealed Specimen ◽  
Plastic Strains ◽  
X Rays ◽  
Lattice Plane ◽  
Coarse Grains

Material of the specimen was austenitic stainless steel (SUS316L). The specimens were given tensile plastic strains from 0% to 55%. The Vickers hardness of the specimen corresponded to the plastic strain. The residual macrostress was measured by Mn-Kα radiations. The residual macrostress of the annealed specimen had a small compression and changed into a tension after ten- sile plastic deformation. The specimen with 1% plastic strain showed the maximum tensile residual stress. To examine the dependency of the residual stress on the lattice plane, the residual microstress for each lattice plane was measured by hard synchrotron X-rays. The residual microstress was related with Young’s modulus which was calculated by Kro¨ ner model. A new method, 2θ-cos2 χ method, was proposed to solve the problem of coarse grains and it was excellent in comparison with the sin2 ψ method.

Residual Stress Evaluation In Austenitic Stainless Steel Butt Weld Joints By Ultrasonic Technique

1992 ◽  
Vol 25 (3) ◽  
pp. 130 ◽  
Author(s):  
P. Palanichamy ◽  
A. Joseph ◽  
K. V. Kasiviswanathan ◽  
D. K. Bhattacharya ◽  
Baldev Raj
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Ultrasonic Technique ◽  
Butt Weld ◽  
Stress Evaluation ◽  
Weld Joints

Residual Stress Evaluation of Ni Based Weld Metal Using Neutron Diffraction Method

2006 ◽  
Vol 524-525 ◽  
pp. 697-702 ◽  
Author(s):  
Shinobu Okido ◽  
Hiroshi Suzuki ◽  
K. Saito
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Neutron Diffraction ◽  
Weld Metal ◽  
Diffraction Method ◽  
Fem Analysis ◽  
Butt Weld ◽  
Stress Evaluation ◽  
Neutron Diffraction Method

Residual stress generated in Type-316 austenitic stainless steel butt-weld jointed by Inconel-182 was measured using a neutron diffraction method and compared with values calculated using FEM analysis. The measured values of Type-316 austenitic stainless steel as base material agreed well with the calculated ones. The diffraction had high intensity and a sharp profile in the base metal. However, it was difficult to measure the residual stress at the weld metal due to very weak diffraction intensities. This phenomenon was caused by the texture in the weld material generated during the weld procedure. As a result, this texture induced an inaccurate evaluation of the residual stress. Procedures for residual stress evaluation to solve this textured material problem are discussed in this paper. As a method for stress evaluation, the measured strains obtained from a different diffraction plane with strong intensity were modified with the ratio of the individual elastic constant. The values of residual stress obtained using this method were almost the same as those of the standard method using Hooke’s law. Also, these residual stress values agreed roughly with those from the FEM analysis. This evaluation method is effective for measured samples with a strong texture like Ni-based weld metal.

scholarly journals Measurement and tailoring of residual stress in expanded austenite on austenitic stainless steel

2017 ◽  
Vol 701 ◽  
pp. 167-173 ◽  
Author(s):  
Frederico A.P. Fernandes ◽  
Thomas L. Christiansen ◽  
Grethe Winther ◽  
Marcel A.J. Somers
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Expanded Austenite

Numerical Simulation and Experimental Investigation of Residual Stress in 06Cr19Ni10 Austenitic Stainless Steel Weld Joint with Effects of Strain-Strengthening

2016 ◽  
Vol 853 ◽  
pp. 204-208 ◽  
Author(s):  
Lan Qing Tang ◽  
Hui Fang Li ◽  
Xiao Xiao Wang ◽  
Cai Fu Qian
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Weld Joint ◽  
Strengthening Effect ◽  
Steel Weld ◽  
Stainless Steel Weld ◽  
Steel Weld Joint ◽  
Austenitic Stainless Steel Weld ◽  
Strain Strengthening

In this paper, Finite Element Modeling (FEM) using Marc software was carried out to investigate the strain-strengthening effect on residual stress in 06Cr19Ni10 austenitic stainless steel weld joint made by MIG welding. The model prediction of residual stress was validated by X-ray Diffraction (XRD) method. It is found that there is a good agreement between the model predictions and the experimental results. The strain-strengthening can significantly improve the distribution of residual welding stress. Specifically in weld zone and the heat-affected zone (HAZ), residual stress decreases with increasing strain-strengthening level.

Sign in / Sign up

Export Citation Format

Share Document