scholarly journals THE EFFECTS OF HEAT TREATMENT ON THE PHYSICAL PROPERTIES OF JUVENILE WOOD AND MATURE WOOD OF EUCALYPTUS GRANDIS

BioResources ◽  
2012 ◽  
Vol 7 (4) ◽  
Author(s):  
Bekir Cihad Bal ◽  
İbrahim Bektaş
Forests ◽  
2019 ◽  
Vol 10 (7) ◽  
pp. 589 ◽  
Author(s):  
Cyriac S. Mvolo ◽  
Ahmed Koubaa ◽  
Jean Beaulieu ◽  
Alain Cloutier ◽  
Maurice Defo ◽  
...  

We examined phenotypic relationships among radial growth-related, physical (i.e., related to wood density), and anatomical (i.e., related to tracheid dimensions) wood properties in white spruce (Picea glauca (Moench) Voss), in order to determine the strength and significance of their correlations. Additionally, principal component analysis (PCA) was used to establish if all of the properties must be measured and to determine the key properties that can be used as proxies for the other variables. Radial growth-related and physical properties were measured with an X-ray densitometer, while anatomical properties were measured with a Fiber Quality Analyzer. Fifteen wood properties (tracheid length (TL) and diameter (TD), earlywood tracheid length (ETL) and diameter (ETD), latewood tracheid length (LTL) and diameter (LTD), ring width (RW), ring area (RA), earlywood width (EWW), latewood width (LWW), latewood proportion (LWP), ring density (RD), intra-ring density variation, earlywood density (EWD), and latewood density (LWD)) were assessed. Relationships were evaluated at intra-ring and inter-ring levels in the juvenile wood (JW) and mature wood (MW) zones. Except for a few cases when mature tracheid diameter (TD) was involved, all intra-ring anatomical properties were highly and significantly correlated. Radial growth properties were correlated, with stronger relationships in MW compared to JW. Physical properties were often positively and significantly correlated in both JW and MW. A higher earlywood density coupled with a lower latewood density favored wood uniformity, i.e., the homogeneity of ring density within a growth ring. Managing plantations to suppress trees growth during JW formation, and enhancing radial growth when MW formation starts will favor overall wood quality. In order, RW-EWW-RA, TL-ETL-LTL, and RD-EWD-LWP are the three clusters that appeared in the three wood zones, the whole pith-to-bark radial section, the juvenile wood zone, and the mature wood zone.


2009 ◽  
Vol 39 (10) ◽  
pp. 1971-1978 ◽  
Author(s):  
Miho Kojima ◽  
Fabio Minoru Yamaji ◽  
Hiroyuki Yamamoto ◽  
Masato Yoshida ◽  
Kouichiro Saegusa

The objective of this study was to determine the factor of xylem maturation in Eucalyptus grandis W. Hill ex Maid. planted in four different latitudes and climatic divisions of South America, based on the pattern of the radial distribution of fiber length. In the plantation closest to the equator, the extent of juvenile wood is determined by distance from the pith and is consistent from tree to tree, regardless of growth rate. In contrast, in the plantation farthest from the equator, xylem maturation is controlled by cambial age and varies from tree to tree, depending on growth rate. To produce as much mature wood as early as possible in E. grandis planted closer to the equator, lateral growth should be accelerated from the early growing stage, because the formation of mature wood starts after a certain trunk diameter is reached. Conversely, in plantations far from the equator, it is necessary to first arrest lateral growth at an early growth stage and then accelerate lateral growth after a certain cambium age is reached.


Author(s):  
Djeison Cesar Batista ◽  
José Tarcísio da Silva Oliveira ◽  
Juarez Benigno Paes ◽  
Silvana Nisgoski ◽  
Graciela Ines Bolzón de Muñiz

2012 ◽  
Vol 2 (3) ◽  
pp. 362-365
Author(s):  
Iqbal S Naji ◽  
◽  
M.F.A.Alias M.F.A.Alias ◽  
Eman M Naser

Alloy Digest ◽  
1953 ◽  
Vol 2 (10) ◽  

Abstract CONDULOY is a low beryllium-copper alloy containing about 1.5% nickel. It responds to age-hardening heat treatment for improved mechanical properties. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on casting, heat treating, machining, and joining. Filing Code: Cu-11. Producer or source: Brush Beryllium Company.


Alloy Digest ◽  
1957 ◽  
Vol 6 (1) ◽  

Abstract WHITE LIGHT-MF is a wrought magnesium-base alloy that does not respond to age-hardening heat treatment for increased hardness and strength. It is a general purpose extrusion alloy for applications where medium strength and economy are prime factors. This datasheet provides information on composition, physical properties, elasticity, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: Mg-30. Producer or source: Whitelight Magnesium Division.


Alloy Digest ◽  
1963 ◽  
Vol 12 (1) ◽  

Abstract ALX is a composition of nonferrous materials with a cobalt base containing chromium, tungsten and carbon. This alloy is commonly supplied in the cast-to-shape form, having an as-cast hardness of Rockwell C60-62 and requiring no further heat treatment. ALX is also supplied as cast tool bit material and is useful where conventional high-speed steels or carbides do not function effectively. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on high temperature performance and corrosion resistance as well as casting, forming, heat treating, and machining. Filing Code: Co-35. Producer or source: Allegheny Ludlum Corporation.


Alloy Digest ◽  
1985 ◽  
Vol 34 (5) ◽  

Abstract ALUMINUM 319.0 is a general-purpose foundry alloy that is moderately responsive to heat treatment. It has excellent casting characteristics and good mechanical properties. Among its many uses are crankcases, housings, engine parts, typewriter frames and rear-axle housings. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as creep and fatigue. It also includes information on low and high temperature performance as well as casting, heat treating, machining, and joining. Filing Code: Al-256. Producer or source: Various aluminum companies.


Sign in / Sign up

Export Citation Format

Share Document