A new method of fluxgate signal extraction

2017 ◽  
Vol 2017 (45) ◽  
pp. 83-89
Author(s):  
A.A. Marusenkov ◽  
Keyword(s):  
High Frequency ◽  
Second Harmonic ◽  
Excitation Frequency ◽  
Low Noise ◽  
Measuring System ◽  
Signal Extraction ◽  
Fluxgate Magnetometer ◽  
New Approach ◽  
Average Value ◽  
The Time Domain

Using dedicated high-frequency measuring system the distribution of the Barkhausen jumps intensity along a reversal magnetization cycle was investigated for low noise fluxgate sensors of various core shapes. It is shown that Barkhausen (reversal magnetization) noise intensity is strongly inhomogeneous during an excitation cycle. In the traditional second harmonic fluxgate magnetometers the signals are extracted in the frequency domain, as a result, some average value of reversal magnetization noises is contributed to the output signals. In order to fit better the noise shape and minimize its transfer to the magnetometer output the new approach for demodulating signals of these sensors is proposed. The new demodulating method is based on information extraction in the time domain taking into account the statistical properties of cyclic reversal magnetization noises. This approach yields considerable reduction of the fluxgate magnetometer noise in comparison with demodulation of the signal filtered at the second harmonic of the excitation frequency.

scholarly journals Lightweight Unmanned Aerial System for Time-Domain Electromagnetic Prospecting—The Next Stage in Applied UAV-Geophysics

2021 ◽  
Vol 11 (5) ◽  
pp. 2060 ◽  
Author(s):  
Alexander Parshin ◽  
Ayur Bashkeev ◽  
Yuriy Davidenko ◽  
Marina Persova ◽  
Sergey Iakovlev ◽  
...  
Keyword(s):  
Time Domain ◽  
Gamma Ray ◽  
Pulse Generator ◽  
Measuring System ◽  
Electromagnetic Sounding ◽  
Mountainous Regions ◽  
Time Domain Electromagnetic ◽  
Unmanned System ◽  
Classical Triad ◽  
The Time Domain

Nowadays in solving geological problems, the technologies of UAV-geophysics, primarily magnetic and gamma surveys, are being increasingly used. However, for the formation of the classical triad of airborne geophysics methods in the UAV version, there was not enough technology for UAV-electromagnetic sounding, which would allow studying the geological environment at depths of tens and hundreds of meters with high detail. This article describes apparently the first technology of UAV-electromagnetic sounding in the time domain (TDEM, TEM), implemented as an unmanned system based on a light multi-rotor UAV. A measuring system with an inductive sensor—an analogue of a 20 × 20 or 50 × 50 m receiving loop is towed by a UAV, and a galvanically grounded power transmitter is on the ground and connected to a pulse generator. The survey is carried out along a network of parallel lines at low altitude with a terrain draping at a speed of 7–8 m/s, the maximum distance of the UAV’s departure from the transmitter line can reach several kilometers, thus the created technology is optimal for performing detailed areal electromagnetic soundings in areas of several square kilometers. The results of the use of the unmanned system (UAS) in real conditions of the mountainous regions of Eastern Siberia are presented. Based on the obtained data, the sensitivity of the system was simulated and it was shown that the developed technology allows one to collect informative data and create geophysical sections and maps of electrical resistivity in various geological situations. According to the authors, the emergence of UAV-TEM systems in the near future will significantly affect the practice of geophysical work, as it was earlier with UAV-magnetic prospecting and gamma-ray survey.

New Method to Determine the a-Si:H Pin Diode Series Resistance by Noise Measurements

1998 ◽  
Vol 507 ◽  
Author(s):  
F. Blecher ◽  
K. Seibel ◽  
M. Hillebrand ◽  
M. Böhm
Keyword(s):  
Series Resistance ◽  
Partial Information ◽  
Low Noise ◽  
Operating Conditions ◽  
New Method ◽  
Measuring System ◽  
Pin Diode ◽  
Noise Current ◽  
Current Voltage ◽  
Noise Measurements

ABSTRACTThe series resistance limits the linearity of photodiodes and decreases the efficiency of solar cells. It is usually determined from IV-measurements for moderate and high forward current density. This method, however, provides only partial information about Rs, since the series resistance depends on the operating point. An alternative method is based on noise measurements. System noise of the measuring system with a low-noise current-voltage converter has been investigated. A new method for extraction of photodiode series resistance from noise measurements is suggested. Noise measurements are carried out for a-Si:H pin diodes. The series resistance of an amorphous pin diode has been extracted for different operating conditions using the new measurement method.

scholarly journals On the Spectral and Polarimetric Signatures of a Bright Scatterer before and after Hardware Replacement

2021 ◽  
Vol 13 (5) ◽  
pp. 919
Author(s):  
Marco Gabella
Keyword(s):  
Low Noise ◽  
Low Noise Amplifiers ◽  
Doppler Velocity ◽  
Data Set ◽  
Differential Phase Shift ◽  
Spectral Signatures ◽  
Average Value ◽  
Before And After ◽  
Radar Calibration ◽  
Small Dispersion

A previous study has used the stable and peculiar echoes backscattered by a single “bright scatterer” (BS) during five winter days to characterize the hardware of C-band, the dual-polarization radar located at Monte Lema (1625 m altitude) in Southern Switzerland. The BS is the 90 m tall metallic tower on Cimetta (1633 m altitude, 18 km range). In this note, the statistics of the echoes from the BS were derived from other ten dry days with normal propagation conditions in winter 2015 and January 2019. The study confirms that spectral signatures, such as spectrum width, wideband noise and Doppler velocity, were persistently stable. Regarding the polarimetric signatures, the large values (with small dispersion) of the copolar correlation coefficient between horizontal and vertical polarization were also confirmed: the average value was 0.9961 (0.9982) in winter 2015 (January 2019); the daily standard deviations were very small, ranging from 0.0007 to 0.0030. The dispersion of the differential phase shift was also confirmed to be quite small: the daily standard deviation ranged from a minimum of 2.5° to a maximum of 5.3°. Radar reflectivities in both polarizations were typically around 80 dBz and were confirmed to be among the largest values observed in the surveillance volume of the Monte Lema radar. Finally, another recent 5-day data set from January 2020 was analyzed after the replacement of the radar calibration unit that includes low noise amplifiers: these five days show poorer characteristics of the polarimetric signatures and a few outliers affecting the spectral signatures. It was shown that the “historical” polarimetric and spectral signatures of a bright scatterer could represent a benchmark for an in-depth comparison after hardware replacements.

scholarly journals Receptivity of Boundary Layer over a Blunt Wedge due to Freestream Pulse Disturbances at Mach 6

2016 ◽  
Vol 2016 ◽  
pp. 1-14 ◽  
Author(s):  
Jianqiang Shi ◽  
Xiaojun Tang ◽  
Zhenqing Wang ◽  
Mingfang Shi ◽  
Wei Zhao
Keyword(s):  
Boundary Layer ◽  
Fundamental Frequency ◽  
High Frequency ◽  
Pulse Wave ◽  
Second Harmonic ◽  
Acoustic Pulse ◽  
Disturbance Wave ◽  
Acoustic Disturbances ◽  
Disturbance Frequency ◽  
Harmonic Components

Direct numerical simulation (DNS) of a hypersonic compressible flow over a blunt wedge with fast acoustic disturbances in freestream is performed. The receptivity characteristics of boundary layer to freestream pulse acoustic disturbances are numerically investigated at Mach 6, and the frequency effects of freestream pulse wave on boundary layer receptivity are discussed. Results show that there are several main disturbance mode clusters in boundary layer under acoustic pulse wave, and the number of main disturbance clusters decreases along the streamwise. As disturbance wave propagates from upstream to downstream direction, the component of the modes below fundamental frequency decreases, and the component of the modes above second harmonic components increases quickly in general. There are competition and disturbance energy transfer between different boundary layer modes. The nose boundary layer is dominated by the nearby mode of fundamental frequency. The number of the main disturbance mode clusters decreases as the freestream disturbance frequency increases. The frequency range with larger growth narrows along the streamwise. In general, the amplitudes of both fundamental mode and harmonics become larger with the decreasing of freestream disturbance frequency. High frequency freestream disturbance accelerates the decay of disturbance wave in downstream boundary layer.

Study of Snubbing Mechanism Using Finite Element Method

2014 ◽  
Author(s):  
Jingming Chen ◽  
Paolo Pennacchi ◽  
Dongxiang Jiang ◽  
Steven Chatterton
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Forced Vibration ◽  
Excitation Frequency ◽  
Relative Displacement ◽  
Rotor Blades ◽  
Motion Pattern ◽  
Motion Characteristics ◽  
The Time Domain ◽  
Element Method

In the rotating machineries, large vibrations of a blade would result in fatigue crack, which is a great threaten to the safety. Therefore, it is of great importance to reduce the blade vibrations. Snubbing technique is a possible solution to this problem. A tiny gap is left between the shrouds of adjacent blades. While the forced vibration makes the relative displacement between two neighboring blades exceed the gap, the contact happens at the contact face of the shrouds, accompanied with friction and energy dissipation, which restricts the vibration. In this paper, a simplified model for a set of rotor blades is established, by using finite element method. The contact between the adjacent shrouds is considered. In this way, snubbing phenomenon can occur under forced vibration. Based on the model, modal analysis has been conducted. The 8x rev. frequency has been chosen as the excitation frequency. Under a certain amplitude of sine excitation, the circumferential vibration of the blades has been simulated. The vibration has been analyzed in the time domain. As expected, the blade motion is divided into four different states in one period. They are: non-contact, rebounding, sticky and escaping state. The four states had different mechanical and motion characteristics. The motion pattern for the set of blades has been also analyzed and the wave spreading along the bladerow has been described. Because of the snubbing mechanism, the waveform was distorted into serrated shape.

Sign in / Sign up

Export Citation Format

Share Document