Solar Power Conditioners Using Bidirectional Chopper Circuits Connected in Series

2012 ◽  
Vol 132 (1) ◽  
pp. 50-57 ◽  
Author(s):  
Hideaki Fujita ◽  
Masao Mabuchi ◽  
Yasuhiro Tsubota ◽  
Takao Mizogami
Keyword(s):  
Author(s):  
Shane Coogan ◽  
Klaus Brun ◽  
David Teraji

The hybrid air Brayton concentrated solar power plant (CSP) combines a natural gas fired combustor in series with a traditional CSP system. The combination boosts turbine inlet temperature above the receiver temperature and reduces output variability. However, a combustor operating in this mode must tolerate an inlet air temperature equal to the solar receiver outlet temperature, which is expected to be as much as 1,000°C for next generation designs. High inlet temperature hybrid combustors must achieve low NOx emissions in spite of the increased risk for autoignition and flashback. In addition, the hybrid injector must be able to adjust to the variability inherent to the solar source. The design of a multibank micromix injector that meets these challenges is described with emphasis on its NOx and CO emissions characteristics.


2013 ◽  
Vol 184 (2) ◽  
pp. 51-60
Author(s):  
Hideaki Fujita ◽  
Masao Mabuchi ◽  
Yasuhiro Tsubota ◽  
Takao Mizogami
Keyword(s):  

2020 ◽  
Vol 307 ◽  
pp. 01002
Author(s):  
Rahul Deep ◽  
Abhishek Mishra ◽  
Anshul Agarwal

Solar energy is most important form of renewable energy. It is cheap and easily available but it required a lot of area for production of solar power to install them in a particular space. This paper proposes a comparison of solar panel in matrix form and a solar power tree in a particular area. A solar power tree requires very less place to produce efficient energy. Solar Tree is made of metal structure , it has a number of solar panels which are used to give the shape of a tree and arranged in a tall tower. Spiralling phyllataxy is technique used to improve the efficiency of the plant as it prevent the lower panel shadowing. Solar photovoltaic modules are arranged in series form like fibonacci series in place of leaves in solar tree. By using this technique the amount of energy produced by solar tree is more than the energy produce by an array of solar cells. Solar trees are produces about 50% more electricity .The increasing energy demand, economy of land, the solar tree concept is very successful one and should be implemented to provide electricity. Solar tree is much better than the traditional solar PV system in area point of view and also more efficient.


2020 ◽  
Vol 63 (9) ◽  
pp. 2921-2929
Author(s):  
Alan H. Shikani ◽  
Elamin M. Elamin ◽  
Andrew C. Miller

Purpose Tracheostomy patients face many adversities including loss of phonation and essential airway functions including air filtering, warming, and humidification. Heat and moisture exchangers (HMEs) facilitate humidification and filtering of inspired air. The Shikani HME (S-HME) is a novel turbulent airflow HME that may be used in-line with the Shikani Speaking Valve (SSV), allowing for uniquely preserved phonation during humidification. The aims of this study were to (a) compare the airflow resistance ( R airflow ) and humidification efficiency of the S-HME and the Mallinckrodt Tracheolife II tracheostomy HME (M-HME) when dry (time zero) and wet (after 24 hr) and (b) determine if in-line application of the S-HME with a tracheostomy speaking valve significantly increases R airflow over a tracheostomy speaking valve alone (whether SSV or Passy Muir Valve [PMV]). Method A prospective observational ex vivo study was conducted using a pneumotachometer lung simulation unit to measure airflow ( Q ) amplitude and R airflow , as indicated by a pressure drop ( P Drop ) across the device (S-HME, M-HME, SSV + S-HME, and PMV). Additionally, P Drop was studied for the S-HME and M-HME when dry at time zero (T 0 ) and after 24 hr of moisture testing (T 24 ) at Q of 0.5, 1, and 1.5 L/s. Results R airflow was significantly less for the S-HME than M-HME (T 0 and T 24 ). R airflow of the SSV + S-HME in series did not significant increase R airflow over the SSV or PMV alone. Moisture loss efficiency trended toward greater efficiency for the S-HME; however, the difference was not statistically significant. Conclusions The turbulent flow S-HME provides heat and moisture exchange with similar or greater efficacy than the widely used laminar airflow M-HME, but with significantly lower resistance. The S-HME also allows the innovative advantage of in-line use with the SSV, hence allowing concurrent humidification and phonation during application, without having to manipulate either device.


Author(s):  
S. P. Bersenev ◽  
E. M. Slobtsova

Achievements in the area of automated ultrasonic control of quality of rails, solid-rolled wheels and tyres, wheels magnetic powder crack detection, carried out at JSC EVRAZ NTMK. The 100% nondestructive control is accomplished by automated control in series at two ultrasonic facilities RWI-01 and four facilities УМКК-1 of magnetic powder control, installed into the exit control line in the wheel-tyre shop. Diagram of location, converters displacement and control operations in the process of control at the facility RWI-01 presented, as well as the structural diagram of the facility УМКК-1. The automated ultrasonic control of rough tyres is made in the tyres control line of the wheel-tyre shop at the facility УКБ-1Д. The facility enables to control internal defects of tyres in radial, axis and circular directions of radiation. Possibilities of the facility УКБ-1Д software were shown. Nondestructive control of railway rails is made at two facilities, comprising the automated control line of the rail and structural shop. The УКР-64Э facility of automated ultrasonic rails control is intended to reveal defects in the area of head, web and middle part of rail foot by pulse echo-method with a immersion acoustic contact. The diagram of rail P65 at the facility УКР-64Э control presented. To reveal defects of the macrostructure in the area of rail head and web by mirror-shadow method, an ultrasonic noncontact electromagnetic-acoustic facility is used. It was noted, that implementation of the 100% nondestructive control into the technology of rolled stuff production enabled to increase the quality of products supplied to customers and to increase their competiveness.


2017 ◽  
Vol 8 (4) ◽  
pp. 1-19
Author(s):  
Oliveira Helio Marques de ◽  
◽  
Giacaglia Giorgio Eugenio Oscare ◽  

Sign in / Sign up

Export Citation Format

Share Document