Thermo-regulating properties of textiles with incorporated microencapsulated Phase Change Materials

MRS Advances ◽  
2020 ◽  
Vol 5 (18-19) ◽  
pp. 1023-1028
Author(s):  
Maria Cristina Larciprete ◽  
Stefano Paoloni ◽  
Gianmario Cesarini ◽  
Concita Sibilia ◽  
Vitalija Rubežienė ◽  
...  
Keyword(s):  
Phase Change ◽  
Phase Change Materials ◽  
Heat Energy ◽  
Infrared Emissivity ◽  
Scanning Calorimetry ◽  
Radiation Emission ◽  
Dynamic Tuning ◽  
Microencapsulated Phase Change Materials ◽  
Cotton Yarns ◽  
Fabric Surface

ABSTRACTPhase change materials (PCMs) are getting increasing interest due to their capacity to absorb, store and release heat energy. Their effectiveness is characterized by quantities of absorbed/released heat energy, expressed as enthalpy. Specifically, the larger is the enthalpy, the more efficient thermoregulation effect is achieved. With this in mind, PCMs can be used in the manufacture of thermally regulated clothing in order to minimize heat strain and simultaneously improve thermal comfort. Moreover, such materials also modify their infrared radiation emission during phase transition, thus they can be envisioned to exploit thermal shielding applications. The aim of the present research was to investigate the infrared emissivity of textiles composed by cotton yarns with dispersed PCMs. The organic microcapsules of phase change materials, having different binding to the fibre mechanisms, were padded onto the fabric surface by pad-dry-cure method. The thermal properties and stabilities were measured using differential scanning calorimetry, while infrared emissivity was characterized using infrared thermographic technique. The obtained experimental results show a dynamic tuning of IR emissivity during heating/cooling process which can be correlated to the type and properties (enthalpy of fusion) of the corresponding PCM.

Microencapsulated Phase Change Materials and its Application in Thermal-Regulated Fibers

2012 ◽  
Vol 519 ◽  
pp. 6-9 ◽  
Author(s):  
Wei Li ◽  
Xing Xiang Zhang ◽  
Xue Chen Wang
Keyword(s):  
Phase Change ◽  
Phase Change Materials ◽  
Formaldehyde Resin ◽  
Dsc Analysis ◽  
Melamine Formaldehyde ◽  
Scanning Calorimetry ◽  
The Core ◽  
Microencapsulated Phase Change Materials ◽  
Spinning Process ◽  
Alginate Fiber

The phase change materials (PCMs) can absorb, store or release large latent heat over a defined temperature range while the materials change phase or state, so they can be potentially used in thermal energy storage. In this paper, a series of microencapsulated phase change materials (MicroPCMs) with n-octadecane and n-dodecanol as core were successfully fabricated respectively, where the styrene-based copolymer, acrylic based copolymer, melamine-formaldehyde resin and polyurea were selected as shell materials. The morphology of these MicroPCMs was observed by scanning electron microscopy (SEM), and the core-shell structure and the shell thickness of microcapsules were also characterized by SEM. In addition, the phase change properties of MicroPCMs were investigated using differential scanning calorimetry (DSC) analysis. Furthermore, thermal-regulated calcium alginate fiber was produced by adding MicroPCMs in wet-spinning process; and the effects of various types of MicroPCMs on fiber was discussed.

scholarly journals Fabrication and characterization of conductive microcapsule containing phase change material

e-Polymers ◽  
2019 ◽  
Vol 19 (1) ◽  
pp. 519-526
Author(s):  
Hao-Ran Yun ◽  
Chun-Lei Li ◽  
Xing-Xiang Zhang
Keyword(s):  
Phase Change ◽  
Phase Change Materials ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
Scanning Calorimetry ◽  
Fourier Transformed Infrared Spectroscopy ◽  
Microencapsulated Phase Change Materials ◽  
Structure Morphology ◽  
Latent Heats

AbstractMicroencapsulated phase change materials (MicroPCMs) were fabricated using n-octadecane as PCM and melamine-formaldehyde as shell via in situ polymerization. They were coated with polypyrrole (PPy) to fabricate conductive microcapsules. The structure, morphology, thermal properties and the electrical conductivity of the microcapsules were characterized using the scanning electron microscope (SEM), the Fourier transformed infrared spectroscopy (FTIR), the thermo gravimetric analysis (TGA), the differential scanning calorimetry (DSC) and the standard four-probe method. The results show that, n-octadecane is well encapsulated in rough and compact spherical composites. The melting and freezing the composites latent heats are 90.2 and 92.0 J/g, respectively, while the mass percentage of the n-octadecane in the composites is 49.7%. The melting and crystallizing peak temperature of PPy/MicroPCMs is 24.6°C and 17.9°C, respectively. The addition of PPy improves the thermal stability of the composites. The conductivity of the PPy/MicroP-CMs increases from 0.1 S‧cm–1 to 0.33 S‧cm–1 as the PPy concentration increases from 3 to 10 wt%.

scholarly journals pH-controlled synthesis of sustainable lauric acid/SiO2 phase change material for scalable thermal energy storage

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shafiq Ishak ◽  
Soumen Mandal ◽  
Han-Seung Lee ◽  
Jitendra Kumar Singh
Keyword(s):  
Electron Microscopy ◽  
Phase Change ◽  
Lauric Acid ◽  
Photoelectron Spectroscopy ◽  
Phase Change Materials ◽  
Precursor Solution ◽  
Thermal Reliability ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Heating And Cooling

AbstractLauric acid (LA) has been recommended as economic, eco-friendly, and commercially viable materials to be used as phase change materials (PCMs). Nevertheless, there is lack of optimized parameters to produce microencapsulated PCMs with good performance. In this study, different amounts of LA have been chosen as core materials while tetraethyl orthosilicate (TEOS) as the precursor solution to form silicon dioxide (SiO2) shell. The pH of precursor solution was kept at 2.5 for all composition of microencapsulated LA. The synthesized microencapsulated LA/SiO2 has been characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS), Scanning electron microscopy (SEM), and Transmission electron microscopy (TEM). The SEM and TEM confirm the microencapsulation of LA with SiO2. Thermogravimetric analysis (TGA) revealed better thermal stability of microencapsulated LA/SiO2 compared to pure LA. PCM with 50% LA i.e. LAPC-6 exhibited the highest encapsulation efficiency (96.50%) and encapsulation ratio (96.15%) through Differential scanning calorimetry (DSC) as well as good thermal reliability even after 30th cycle of heating and cooling process.

scholarly journals Characterization of Unripe and Mature Avocado Seed Oil in Different Proportions as Phase Change Materials and Simulation of Their Cooling Storage

Molecules ◽  
2020 ◽  
Vol 26 (1) ◽  
pp. 107
Author(s):  
Evelyn Reyes-Cueva ◽  
Juan Francisco Nicolalde ◽  
Javier Martínez-Gómez
Keyword(s):  
Phase Change ◽  
Phase Change Materials ◽  
Seed Oil ◽  
Energy System ◽  
Maturity Stage ◽  
Natural Environments ◽  
Renewable Materials ◽  
Scanning Calorimetry ◽  
Avocado Seed

Environmental problems have been associated with energy consumption and waste management. A solution is the development of renewable materials such as organic phase change materials. Characterization of new materials allows knowing their applications and simulations provide an idea of how they can developed. Consequently, this research is focused on the thermal and chemical characterization of five different avocado seed oils depending on the maturity stage of the seed: 100% unripe, 25% mature-75% unripe, 50% mature-50% unripe, 75% mature-25% unripe, and 100% mature. The characterization was performed by differential scanning calorimetry, Fourier transform infrared spectroscopy, and thermogravimetric analysis. The best oil for natural environments corresponded to 100% matured seed with an enthalpy of fusion of 52.93 J·g−1, and a degradation temperature between 241–545 °C. In addition, the FTIR analysis shows that unripe seed oil seems to contain more lipids than a mature one. Furthermore, a simulation with an isothermal box was conducted with the characterized oil with an initial temperature of −14 °C for the isothermal box, −27 °C for the PCM box, and an ambient temperature of 25 °C. The results show that without the PCM the temperature can reach −8 °C and with it is −12 °C after 7 h, proving its application as a cold thermal energy system.

Sign in / Sign up

Export Citation Format

Share Document