Detection of contact damage in ceramics by an ultrasonic method

1998 ◽  
Vol 13 (7) ◽  
pp. 1899-1904 ◽  
Author(s):  
Hyo Sok Ahn ◽  
Said Jahanmir ◽  
John A. Slotwinski ◽  
Gerald V. Blessing
Keyword(s):  
Silicon Nitride ◽  
Glass Ceramic ◽  
Ultrasonic Method ◽  
Circular Ring ◽  
Ultrasonic Technique ◽  
Surface Cracks ◽  
Compressional Waves ◽  
Different Depths ◽  
Pulse Echo ◽  
Hertzian Cone

A pulse-echo ultrasonic technique consisting of focused normal-incident compressional waves was used for the detection and evaluation of surface and subsurface damage in micaceous glass-ceramic and silicon nitride samples. The damage was produced by indentation with a tungsten carbide ball. The nature of the damage was found to be material-dependent and was classified into two types: Hertzian cone cracks in the silicon nitride, and distributed subsurface microcracks in the glass-ceramic. While the cone cracks were visible on the surface as circular ring cracks, the distributed subsurface microcracks were not associated with any visible surface cracks. Both the cone cracks and the distributed subsurface microcracks were easily detected by the ultrasonic technique. In addition, the ultrasonic beam was focused to different depths below the surface of the glass-ceramic sample to probe the subsurface region containing the microfracture damage.

Sizing Detection of a Surface-Breaking Crack by Ultrasonic Technique

2011 ◽  
Vol 52-54 ◽  
pp. 865-868 ◽  
Author(s):  
Shiuh Chuan Her ◽  
Sheng Tung Lin
Keyword(s):  
Test Specimen ◽  
Incident Angle ◽  
Ultrasonic Technique ◽  
Non Destructive Evaluation ◽  
Different Depths ◽  
Crack Sizing ◽  
Incident Waves ◽  
Surface Breaking Crack ◽  
Pulse Echo ◽  
Non Destructive

Ultrasonic is one of the most common uses of non-destructive evaluation technique. It could detect flaws inside the structure and on the surface such as voids, holes and cracks. In this investigation, a 304 steel block with a surface-breaking crack was fabricated. A series of test specimen with different depths of surface-breaking crack ranging from 2mm to 9mm was fabricated. The depth of the surface crack was evaluated by the pulse-echo ultrasonic technique. In this work, 2.25MHz, 5MHz and 10MHz of incident waves were employed to detect the depth of the surface-breaking crack. The effect of incident angle on the measuring accuracy was investigated. Experimental results showed that the accuracy of crack sizing detection by ultrasonic technique is not only dependent on the frequency of the incident wave but also dependent on the incident angle.

A Practical Ultrasonic Inspection Method for Detecting and Characterising Defects Found Within Composite Repairs

2018 ◽  
Author(s):  
J Downing ◽  
A Hook
Keyword(s):  
Wall Thickness ◽  
Steel Substrate ◽  
Ultrasonic Method ◽  
Ultrasonic Inspection ◽  
Heat Exposure ◽  
Matrix Cracking ◽  
Ultrasonic Technique ◽  
Inspection Method ◽  
Composite Repairs ◽  
Layered Matrix

Two steel substrate test panels were developed to represent common plate thicknesses found on naval vessels and scanned using the Babcock developed ultrasonic technique. One sample comprised of a series of slotted surface breaking flaws of varying widths and through thicknesses to represent fracturing/cracking. The inspection method detected simulated cracking to a depth of 2mm and 0.5mm in width. The second sample included numerous loss of wall thickness areas of varying diameters and through thicknesses, with the smallest detectable loss of wall thickness being 0.1mm at a 15mm diameter. After proving confidence in detection, there was a need to characterise flaws to provide support and ascertain a repair action. Samples were produced that were subjected to either impact or heat exposure to induce realistic representative damage. The practical ultrasonic method was successfully used to independently characterise between the samples, with induced de-laminations caused by blisters, and multi layered matrix cracking caused by varying levels of projectile impacts, due to their unique morphology.

Laser-Generated Ultrasonic Technique for Inspecting Delamination in CFRP

2006 ◽  
Vol 321-323 ◽  
pp. 968-971
Author(s):  
Won Su Park ◽  
Sang Woo Choi ◽  
Joon Hyun Lee ◽  
Kyeong Cheol Seo ◽  
Joon Hyung Byun
Keyword(s):  
High Frequency ◽  
Ultrasonic Method ◽  
Piezoelectric Sensor ◽  
Frequency Component ◽  
Guided Wave ◽  
Center Frequency ◽  
High Frequency Component ◽  
Ultrasonic Technique ◽  
Non Destructive Evaluation ◽  
Non Destructive

For improving quality of a carbon fiber reinforced composite material (CFRP) by preventing defects such as delamination and void, it should be inspected in fabrication process. Novel non-contacting evaluation technique is required because the transducer should be contacted on the CFRP in conventional ultrasonic technique during the non-destructive evaluation and these conventional contact techniques can not be applied in a novel fiber placement system. For the non-destructive evaluation of delamination in CFRP, various methods for the generation and reception of laser-generated ultrasound are applied using piezoelectric transducer, air-coupled transducer, wavelet transform technique etc. The high frequency component of laser-generated guided wave received with piezoelectric sensor disappeared after propagating through delamination region. Air-coupled transducer was tried to be adopted in reception of laser-generated guided wave generated by using linear slit array in order to generate high frequency guided wave with a frequency of 1.1 MHz. Nevertheless, it was failed to receive high frequency guided wave in using air-coupled transducer and linear slit array. Transmitted laser-generated ultrasonic wave was received on back-wall and its frequency was analyzed to establish inspecting technique to detect delamination by non-contact ultrasonic method. In a frequency spectrum analysis, intensity ratio of low frequency and center frequency was approvable parameter to detect delamination.

Measuring the Frequency-Dependent Attenuation Coefficients of Solids Using a Pulse-Echo Ultrasonic Method

2021 ◽  
Author(s):  
Guangdong Zhang ◽  
Xiongbing Li ◽  
Shuzeng Zhang ◽  
Tribikram Kundu
Keyword(s):  
Ultrasonic Method ◽  
Attenuation Coefficients ◽  
Frequency Dependent ◽  
Pulse Echo

Long Wavelength Measurements of Surface Cracks in Silicon Nitride

1982 ◽  
pp. 569-571 ◽  
Author(s):  
J. J. Tien ◽  
B. T. Khuri-Yakub ◽  
G. S. Kino ◽  
A. G. Evans ◽  
D. Marshall
Keyword(s):  
Silicon Nitride ◽  
Surface Cracks ◽  
Long Wavelength

scholarly journals Air-Coupled and Resonant Pulse-Echo Ultrasonic Technique

Sensors ◽  
2019 ◽  
Vol 19 (10) ◽  
pp. 2221 ◽  
Author(s):  
Tomás Gómez Álvarez-Arenas ◽  
Jorge Camacho
Keyword(s):  
Resonant Frequency ◽  
Decay Time ◽  
Dead Zone ◽  
Steel Plates ◽  
Angle Of Incidence ◽  
Ultrasonic Technique ◽  
First Wall ◽  
Resonant Modes ◽  
Quality Factor Q ◽  
Pulse Echo

An ultrasonic, resonant, pulse-echo, and air-coupled nondestructive testing (NDT) technique is presented. It is intended for components, with regular geometries where it is possible to excite resonant modes, made of materials that have a high acoustic impedance (Z) and low attenuation coefficient (α). Under these conditions, these resonances will present a very large quality factor (Q) and decay time (τ). This feature is used to avoid the dead zone, produced by the echo coming from the first wall, by receiving the resonant echo from the whole specimen over a longer period of time. This echo is analyzed in the frequency domain to determine specimen resonant frequency, which can be further used to determine either velocity or thickness. Using wideband air-coupled transducers, we tested the technique on plates (steel, aluminum, and silicone rubber) by exciting the mode of the first thickness. As expected, the higher the Z and the lower the α, the better the technique performed. Sensitivity to deviations of the angle of incidence away from normal (±2°) and the possibility to generate shear waves were also studied. Then, it was tested on steel cylindrical pipes that had different wall thicknesses and diameters. Finally, the use of this technique to generate C-Scan images of steel plates with different thicknesses was demonstrated.

Sign in / Sign up

Export Citation Format

Share Document