Strain Rate Sensitivity of a Nanocrystalline Cu–Ni–P Alloy

2005 ◽  
Vol 20 (11) ◽  
pp. 2955-2959 ◽  
Author(s):  
J. Chen ◽  
Y.N. Shi ◽  
K. Lu
Keyword(s):  
Grain Size ◽  
Grain Boundary ◽  
Strain Rate ◽  
Grain Boundaries ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Nanoindentation Technique ◽  
Pure Cu

Nanoindentation technique was used to measure the strain rate sensitivity (m) of a nanocrystalline Cu-Ni-P alloy prepared by means of electrodeposition. The m value decreases from 0.034 to 0.018 when the nominal grain size increases from 7 nm to 33 nm. Both m values of the alloy are obviously lower than those of the pure Cu with similar grain size, implying that P segregation at grain boundaries might play a key role in retarding grain boundary activities as compared to pure Cu samples.

Effects of Strain Rate and Grain Size on Behavior of Nano Crystalline Materials

2012 ◽  
Vol 17 ◽  
pp. 35-51 ◽  
Author(s):  
Reza Jafari Nedoushan ◽  
Mahmoud Farzin ◽  
Mohammad Mashayekhi
Keyword(s):  
Grain Size ◽  
Grain Boundary ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Grain Boundary Sliding ◽  
Deformation Mechanisms ◽  
Coarse Grained ◽  
Crystalline Materials ◽  
Nano Crystalline

Recent Experiments on Nano-Crystalline Materials Show an Increase of Strain-Rate Sensitivity in Contrast to the Conventional Coarse-Grained Materials. these Materials Also Show a Different Grain Size Dependency as Compared to Coarse-Grained Materials. to Explain these Issues, a Constitutive Equation Is Proposed which Considers Dominant Deformation Mechanisms Including Grain Interior Plasticity, Grain Boundary Diffusion and Grain Boundary Sliding. the Stresses Obtained from these Constitutive Equations Match Well with the Experimental Data for Nanocrystalline Copper at Different Strains and Strain Rates. the Model Also Well Predicts Variation of Strain Rate Sensitivity Parameter. this Variation Can Be Explained with Regard to the above Mentioned Effective Deformation Mechanisms. Deviation from the Hall-Petch Law and Inverse Hall-Petch Effect Are Also Well Illustrated by the Model.

Temperature Effects in Al 5083 with a Bimodal Grain Size

2013 ◽  
Vol 1513 ◽  
Author(s):  
Andrew C. Magee ◽  
Leila J. Ladani
Keyword(s):  
Grain Size ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Cold Isostatic Pressing ◽  
Milling Process ◽  
Dynamic Strain ◽  
Plastic Properties ◽  
Al 5083 Alloy ◽  
Bimodal Grain Size

ABSTRACTAn Al 5083 alloy with a bimodal grain size has been previously synthesized using a low-temperature milling process and consolidation via cold isostatic pressing (CIP). This material has been shown to exhibit greatly improved strength when compared to conventional aluminum alloys. Additionally, this material has shown sensitivity to test conditions. In this work, we studied the effects of temperature on the strain rate sensitivity of this material by examining its elastic and plastic properties though uniaxial tension tests conducted under a variety of conditions at temperatures up to 473 K. Serrated stress-strain curves were observed, indicating dynamic strain aging. Strain rate sensitivity was found to depend non-monotonically on the test temperature.

scholarly journals Influence of Mo Segregation at Grain Boundaries on the High Temperature Creep Behavior of Ni-Mo Alloys: An Atomistic Study

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 6966
Author(s):  
Qian Li ◽  
Jiayong Zhang ◽  
Huayuan Tang ◽  
Hongwu Zhang ◽  
Hongfei Ye ◽  
...  
Keyword(s):  
Grain Size ◽  
Grain Boundary ◽  
Strain Rate ◽  
Grain Boundaries ◽  
Creep Strain ◽  
High Stress ◽  
External Stress ◽  
Creep Strain Rate ◽  
Creep Process ◽  
Boundary Slip

Based on molecular dynamics simulations, the creep behaviors of nanocrystalline Ni before and after the segregation of Mo atoms at grain boundaries are comparatively investigated with the influences of external stress, grain size, temperature, and the concentration of Mo atoms taken into consideration. The results show that the creep strain rate of nanocrystalline Ni decreases significantly after the segregation of Mo atoms at grain boundaries due to the increase of the activation energy. The creep mechanisms corresponding to low, medium, and high stress states are respectively diffusion, grain boundary slip and dislocation activities based on the analysis of stress exponent and grain size exponent for both pure Ni and segregated Ni-Mo samples. Importantly, the influence of external stress and grain size on the creep strain rate of segregated Ni-Mo samples agrees well with the classical Bird-Dorn-Mukherjee model. The results also show that segregation has little effect on the creep process dominated by lattice diffusion. However, it can effectively reduce the strain rate of the creep deformation dominated by grain boundary behaviors and dislocation activities, where the creep rate decreases when increasing the concentration of Mo atoms at grain boundaries within a certain range.

Slip Induced Strain Rate Sensitivity for Superplastic Material?

2012 ◽  
Vol 735 ◽  
pp. 31-36 ◽  
Author(s):  
Hector Basoalto ◽  
Paul L. Blackwell
Keyword(s):  
Grain Boundary ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Rate Sensitivity ◽  
Grain Boundary Sliding ◽  
Dislocation Slip ◽  
Microstructural Parameters ◽  
Sliding Mechanism ◽  
Physically Based ◽  
Boundary Sliding

The conventional consensus has it that the magnitude of the strain rate sensitivity observed in superplastic materials is linked with grain boundary sliding. The grain boundary sliding mechanism is thought to theoretically produce a strain rate sensitivity exponent of 0.5, which is in good agreement with experimental data. The present paper argues that a rate sensitivity of 0.5 can be generated by dislocation slip under certain temperature and strain rate regimes that overlap with conditions representative of superplasticity. A physically based slip model that links the relevant microstructural parameters to the macroscopic strain rate is proposed.

Strain-Rate Sensitivity Enhanced by Grain-Boundary Sliding in Creep Condition for AZ31 Magnesium Alloy at Room Temperature

2016 ◽  
Vol 838-839 ◽  
pp. 106-109 ◽  
Author(s):  
Tetsuya Matsunaga ◽  
Hidetoshi Somekawa ◽  
Hiromichi Hongo ◽  
Masaaki Tabuchi
Keyword(s):  
Grain Boundary ◽  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
Room Temperature ◽  
High Strain ◽  
Rate Sensitivity ◽  
Grain Boundary Sliding ◽  
Strain Rates ◽  
High Strain Rates ◽  
Boundary Sliding

This study investigated strain-rate sensitivity (SRS) in an as-extruded AZ31 magnesium (Mg) alloy with grain size of about 10 mm. Although the alloy shows negligible SRS at strain rates of >10-5 s-1 at room temperature, the exponent increased by one order from 0.008 to 0.06 with decrease of the strain rate down to 10-8 s-1. The activation volume (V) was evaluated as approximately 100b3 at high strain rates and as about 15b3 at low strain rates (where b is the Burgers vector). In addition, deformation twin was observed only at high strain rates. Because the twin nucleates at the grain boundary, stress concentration is necessary to be accommodated by dislocation absorption into the grain boundary at low strain rates. Extrinsic grain boundary dislocations move and engender grain boundary sliding (GBS) with low thermal assistance. Therefore, GBS enhances and engenders SRS in AZ31 Mg alloy at room temperature.

Sign in / Sign up

Export Citation Format

Share Document