Nanoporous zero-valent iron

2005 ◽  
Vol 20 (12) ◽  
pp. 3238-3243 ◽  
Author(s):  
Jiasheng Cao ◽  
Patrick Clasen ◽  
Wei-xian Zhang
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Performance Enhancement ◽  
Zero Valent Iron ◽  
Iron Particles ◽  
Surface Areas ◽  
Batch Tests ◽  
Resin Beads ◽  
Solid Iron

Hollow and nanoporous particles of zero-valent iron (ZVI) were prepared with template-directed synthesis. Polymer resin beads (0.4 mm diameter) were coated with nanoscale iron particles by reductive precipitation of ferrous iron [Fe(II)] with sodium borohydride. The resin was calcinated at 400 °C to produce hollow and nanoporous iron spheres. The nanoporous iron oxides were then reduced to metallic iron by hydrogen at 500 °C. Scanning electron microscope images of the reduced iron spheres showed that the particles were hollow. The shell thickness was approximately 5 μm and highly porous. Brunauer–Emmett–Teller specific surface area was 2100 m2/kg. In comparison, the theoretical specific surface area of solid iron particles of the same size is just 1.9 m2/kg. Batch tests showed that the surface area normalized reactivity of the porous particles were 14–31% higher than microscale iron particles with similar surface areas for the transformation of hexavalent chromium [Cr(VI)], azo dye Orange II {4-[(2-hydroxyl-1-naphthalenyl)azo]-benzenesulfonic acid monosodium}, and trichloroethene. The combined performance enhancement (larger surface area and higher surface activity) is significant (>1200 times).

Effect of ZnO Particle Size on the Curing of Carboxylated NBR and Carboxylated SBR

2004 ◽  
Vol 77 (2) ◽  
pp. 214-226 ◽  
Author(s):  
G. R. Hamed ◽  
K.-C. Hua
Keyword(s):  
Zinc Oxide ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Cure Rate ◽  
Surface Areas ◽  
Diffusion Limited ◽  
Rate Of Dissolution ◽  
Oxide Particles ◽  
And Diffusion

Abstract A carboxylated nitrile rubber (XNBR) and a carboxylated SBR (XSBR) were mixed with zinc oxide particles of different specific surface areas (“S”, 35 m2/g; “M”, 3.5m2/g; “L”, 0.5 m2/g) and cure behavior at 165 ºC studied using oscillating disc rheometry. Without added zinc oxide, both raw rubbers slowly stiffen over many hours of heating. This is probably due to condensation of carboxyl groups to form anhydride crosslinks. XNBR compositions containing the finely divided “S” crosslink much more rapidly. Full cure is reached after about 10 minutes of heating. Cure rate decreases markedly as the specific surface area of the ZnO decreases. A composition containing “M” at twice stoichiometry requires about an hour to cure well, while with “L”, about 10 hours are required. In contrast, curing of the XSBR depends little on the specific surface area of the ZnO, either with “S” or “L”, curing is essentially complete after 30 minutes. After simply mixing ZnO into either rubber, it remains as a dispersed particulate. With XNBR, curing appears to be controlled by the rate of dissolution and diffusion of ZnO, while, with XSBR, reaction is not diffusion limited and may be confined to regions near particle surfaces.

A Comparison of Methods for Determining Surface Areas of Carbon Black

1973 ◽  
Vol 46 (1) ◽  
pp. 192-203 ◽  
Author(s):  
R. A. Klyne ◽  
B. D. Simpson ◽  
M. L. Studebaker
Keyword(s):  
Carbon Black ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Surface Areas ◽  
Furnace Black ◽  
Area Increase ◽  
Experimental Errors ◽  
Specific Surface Areas ◽  
Surface Area Increase

Abstract 1. The various tint tests correlate with each other—it does not make much difference which of the three procedures is used. The discrimination between similar blacks is comparable. Specific surface areas obtained by the three methods are comparable and differences appear to be due to experimental errors. (Compare Figures 5–7). 2. Surface areas larger than some 90 to 100 m2/g cannot be reliably determined from tint strength measurements alone. 3. Structure exerts a pronounced effect on tint strength of furnace blacks, especially above 90 to 100 m2/g. Porosity and/or composition are apparently also variables which affect tinting strength. 4. Densichron reflectance on the dry carbon black can be used to estimate specific surface areas up to about 140 m2/g; but, since theabsoluteerrorincreases as the specific surface area increases, this method loses some of its reliability at values above about 110 m2/g. The relative error in reflectance determinations does not vary greatly over the furnace-black range. Densichron reflectance is influenced by composition, evidently due to composition-related differences in optical properties of the carbons. 5. In CTAB adsorption measurements, titration errors and handling errors tend to be rather constant for blacks of different surface area. Hence, CTAB permits better discrimination among blacks of small particle size. 6. The errors in Densichron reflectance surface area increase with specific surface area. Hence, the deviations between CTAB and reflectance surface area which are due to experimental error increase with the surface area of the sample.

scholarly journals A Case Study of Waste Scrap Tyre-Derived Carbon Black Tested for Nitrogen, Carbon Dioxide, and Cyclohexane Adsorption

Molecules ◽  
2020 ◽  
Vol 25 (19) ◽  
pp. 4445 ◽  
Author(s):  
Zuzana Jankovská ◽  
Marek Večeř ◽  
Ivan Koutník ◽  
Lenka Matějová
Keyword(s):  
Activated Carbon ◽  
Carbon Black ◽  
Specific Surface ◽  
Surface Area ◽  
Sorption Capacity ◽  
Specific Surface Area ◽  
Textural Properties ◽  
Pyrolytic Carbon ◽  
Surface Areas ◽  
Wide Range

Waste scrap tyres were thermally decomposed at the temperature of 600 °C and heating rate of 10 °C·min−1. Decomposition was followed by the TG analysis. The resulting pyrolytic carbon black was chemically activated by a KOH solution at 800 °C. Activated and non-activated carbon black were investigated using high pressure thermogravimetry, where adsorption isotherms of N2, CO2, and cyclohexane were determined. Isotherms were determined over a wide range of pressure, 0.03–4.5 MPa for N2 and 0.03–2 MPa for CO2. In non-activated carbon black, for the same pressure and temperature, a five times greater gas uptake of CO2 than N2 was determined. Contrary to non-activated carbon black, activated carbon black showed improved textural properties with a well-developed irregular mesoporous-macroporous structure with a significant amount of micropores. The sorption capacity of pyrolytic carbon black was also increased by activation. The uptake of CO2 was three times and for cyclohexane ten times higher in activated carbon black than in the non-activated one. Specific surface areas evaluated from linearized forms of Langmuir isotherm and the BET isotherm revealed that for both methods, the values are comparable for non-activated carbon black measured by CO2 and for activated carbon black measured by cyclohexane. It was found out that the N2 sorption capacity of carbon black depends only on its specific surface area size, contrary to CO2 sorption capacity, which is affected by both the size of specific surface area and the nature of carbon black.

Experimental Studies of Carbon Electrodes With Various Surface Area for Li–O2 Batteries

2019 ◽  
Vol 16 (4) ◽  
Author(s):  
Fangzhou Wang ◽  
P. K. Kahol ◽  
Ram Gupta ◽  
Xianglin Li
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Discharge Capacity ◽  
Carbon Materials ◽  
High Specific Surface Area ◽  
Acetylene Black ◽  
Carbon Electrodes ◽  
Tea Leaves ◽  
Surface Areas

Li−O2 batteries with carbon electrodes made from three commercial carbons and carbon made from waste tea leaves are investigated in this study. The waste tea leaves are recycled from household tea leaves and activated using KOH. The carbon materials have various specific surface areas, and porous structures are characterized by the N2 adsorption/desorption. Vulcan XC 72 carbon shows a higher specific surface area (264.1 m2/g) than the acetylene black (76.5 m2/g) and Super P (60.9 m2/g). The activated tea leaves have an extremely high specific surface area of 2868.4 m2/g. First, we find that the commercial carbons achieve similar discharge capacities of ∼2.50 Ah/g at 0.5 mA/cm2. The micropores in carbon materials result in a high specific surface area but cannot help to achieve higher discharge capacity because it cannot accommodate the solid discharge product (Li2O2). Mixing the acetylene black and the Vulcan XC 72 improves the discharge capacity due to the optimized porous structure. The discharge capacity increases by 42% (from 2.73 ± 0.46 to 3.88 ± 0.22 Ah/g) at 0.5 mA/cm2 when the mass fraction of Vulcan XC 72 changes from 0 to 0.3. Second, the electrode made from activated tea leaves is demonstrated for the first time in Li−O2 batteries. Mixtures of activated tea leaves and acetylene black confirm that mixtures of carbon material with different specific surface areas can increase the discharge capacity. Moreover, carbon made from recycled tea leaves can reduce the cost of the electrode, making electrodes more economically achievable. This study practically enhances the discharge capacity of Li−O2 batteries using mixed carbons and provides a method for fabricating carbon electrodes with lower cost and better environmental friendliness.

Valorization of cellulose-doped lignin: application of cellulose-doped lignin-derived activated carbon in capacitors and investigation of its textural properties and electrochemical performance

2021 ◽  
Author(s):  
Liangcai Wang ◽  
Xin Feng ◽  
Huanhuan Ma ◽  
Jielong Wu ◽  
Yu Chen ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Specific Capacitance ◽  
Surface Area ◽  
Specific Surface Area ◽  
Wall Thickness ◽  
Textural Properties ◽  
Pore Wall ◽  
Surface Areas ◽  
Pore Wall Thickness

Abstract This work provides an idea for efficient and harmless utilization of lignin and further evaluated the textural properties of lignin-derived activated carbon/specific capacitance relationship. The yield of cellulose-doped apricot shell lignin (ASLC) was 30.42%. H3PO4/KOH was used to assist the preparation of ASLC-derived activated carbon (AAC) for capacitors. The specific surface areas of the as-obtained AAC-P-3 and AAC-K-2 were 1475.16 m2/g and 2136.56 m2/g, respectively. The specific capacitances of AAC-P-3 and AAC-K-2 were 169.14 F/g and 236.00 F/g, respectively, upon the current density of 0.50 A/g. In capacitors containing aqueous KOH as the electrolyte, the AR2 (0.983) between specific surface area and specific capacitance was highest, followed by the AR2 (0.978) between Vmicro/Vmeso and specific capacitance, the AR2 (0.975) between pore-wall thickness and specific capacitance. Consequently, the specific capacitances of the AACs depend not only the specific surface area, but also on the Vmicro/Vmeso, pore-wall thickness, and Vmicro.

scholarly journals Textural and structural modifications of saponite from Cerro del Aguila by acid treatment

Clay Minerals ◽  
2001 ◽  
Vol 36 (4) ◽  
pp. 483-488 ◽  
Author(s):  
M. Suárez Barrios ◽  
C. de Santiago Buey ◽  
E. García Romero ◽  
J. M. Martín Pozas
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Acid Treatment ◽  
Active Sites ◽  
Internal Surface ◽  
Acid Activation ◽  
Acid Attack ◽  
Surface Areas ◽  
Treated Sample

AbstractThe physicochemical properties of clays can be modified by acid treatment with inorganic acids. This treatment is usually referred to as ‘acid activation’, because it increases the specific surface area and the number of active sites of the solids. In the present study, the acid activation of saponite from Cerro del Aguila (Madrid, Spain) with HCl solutions was measured. Illite, quartz and small amounts of feldspar were found as impurities in the raw saponite.Acid treatments were carried out with different concentrations of HCl solutions. The samples obtained were characterized by mineralogical and chemical analyses, XRD, FT-IR spectroscopy, N2 adsorption-desorption isotherms and TEM. The acid attack, under the conditions employed, produced a progressive destruction of the structure of saponite by partial dissolution of the octahedral Mg(II) cations. Amorphous silica coming from the tetrahedral sheet of saponite was generated. The specific surface area of the most intensely treated sample (2.5% for 24 h) was doubled with respect to that of natural saponite. This increase in the surface area is due to the increase in both the external and internal surface areas.

scholarly journals Preparation and characterization of high specific surface area Mn3O4 from electrolytic manganese residue

2010 ◽  
Vol 8 (5) ◽  
pp. 1059-1068 ◽  
Author(s):  
Tiefeng Peng ◽  
Longjun Xu ◽  
Hongchong Chen
Keyword(s):  
Particle Size ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Magnetic Measurements ◽  
High Specific Surface Area ◽  
Surface Areas ◽  
Electrolytic Manganese ◽  
Electrolytic Manganese Residue ◽  
Specific Surface Areas

AbstractMn3O4 powders have been produced from Electrolytic Manganese Residue (EMR). After leaching of EMR in sulfuric acid, MnSO4 solution containing various ions was obtained. Purifying the solution obtained and then adding aqueous alkali to the purified MnSO4 solution, Mn(OH)2 was prepared. Two methods were employed to produce Mn3O4. One way was oxidation of Mn(OH)2 in aqueous phase under atmosphere pressure to obtain Mn3O4. The other way was roasting Mn(OH)2 precursors in the range of 500°C to 700°C. The prepared samples were investigated by using several techniques including X-ray powder diffraction (XRD), Fourier Transformation Infra-Red (FTIR) spectra, and Brunauer-Emmett-Teller (BET) specific surface area instrument. Particle distribution and magnetic measurements were carried out on laser particle size analyzer, vibrating sample magnetometer (VSM). Through XRD, FTIR and determination of total Mn content (TMC), the products prepared were confirmed to be a single phase Mn3O4. BET specific surface areas can reach to 32 m2 g−1. The results indicated that products synthesized by aqueous solution oxidation method had higher specific surface areas and smaller particle size than those prepared by means of roasting. However the products prepared using the above two methods showed no obvious differences in magnetic property.

scholarly journals Adsorption of water vapour and the specific surface area of arctic zone soils (Spitsbergen)

2018 ◽  
Vol 32 (1) ◽  
pp. 19-27 ◽  
Author(s):  
Jolanta Cieśla ◽  
Zofia Sokołowska ◽  
Barbara Witkowska-Walczak ◽  
Kamil Skic
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Water Vapour ◽  
Specific Surface Area ◽  
Nitrogen Adsorption ◽  
Total Carbon ◽  
Arctic Zone ◽  
Surface Areas ◽  
Arctic Soils ◽  
Specific Surface Areas

AbstractWater vapour/nitrogen adsorption were investigated and calculated the specific surface areas of arctic-zone soil samples (Turbic Cryosols) originating from different micro-relief forms (mud boils, cell forms and sorted circles) and from different depths. For the characterisation of the isotherms obtained for arctic soils, the Brunauer-Emmet-Teller model was then compared with the two other models (Aranovich-Donohue and Guggenheim-Anderson-de Boer) which were developed from Brunauer-Emmet-Teller. Specific surface area was calculated using the Brunauer-Emmet-Teller model at p p0−1range of 0.05-0.35 for the water vapour desorption and nitrogen adsorption isotherms. The values of total specific surface area were the highest in Cryosols on mud boils, lower on cell forms, and the lowest on sorted circles. Such tendency was observed for the results obtained by both the water vapour and nitrogen adsorption. The differences in the values of specific surface area at two investigated layers were small. High determination coefficients were obtained for relationships between the specific surface areas and contents of clay and silt fraction in Cryosols. No statistically significant correlation between the total carbon amount and the values of specific surface area in Cryosols has been found.

SEM and BET Methods for Investigating the Structure and Morphology of Co - Ce Catalysts for Production of Light Olefins

2008 ◽  
Vol 61 (2) ◽  
pp. 144 ◽  
Author(s):  
Ali A. Mirzaei ◽  
Maryam Galavy ◽  
Vahid Eslamimanesh
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Catalytic Performance ◽  
Light Olefins ◽  
Molar Ratio ◽  
Surface Areas ◽  
Preparation Conditions ◽  
Bet Specific Surface Area ◽  
Before And After

Co–Ce catalysts prepared by the coprecipitation method were tested for production of light olefins. The effect of different preparation conditions including the [Co]/[Ce] molar ratio, aging time, calcination conditions, different supports, and loading of optimum support on the structure and catalytic performance of different catalysts were investigated. It was found that catalyst containing 80% Co/20% Ce/15% SiO2, which was aged for 2 h and calcined at 600°C for 6 h, is the optimum modified catalyst for the conversion of synthesis gas to light olefins. Characterization of both precursors and calcined catalysts (before and after the test) was carried out using scanning electron microscopy (SEM) and Brunauer-Emmett-Teller (BET) specific surface area measurements. The morphology of the catalysts was investigated by SEM and the surface areas of these catalysts were studied by BET. It was shown that all of the different preparation variables influenced the morphology and also the specific surface area of the catalyst precursors and calcined catalysts.

Sign in / Sign up

Export Citation Format

Share Document