Effect of ZnO Particle Size on the Curing of Carboxylated NBR and Carboxylated SBR

2004 ◽  
Vol 77 (2) ◽  
pp. 214-226 ◽  
Author(s):  
G. R. Hamed ◽  
K.-C. Hua
Keyword(s):  
Zinc Oxide ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Cure Rate ◽  
Surface Areas ◽  
Diffusion Limited ◽  
Rate Of Dissolution ◽  
Oxide Particles ◽  
And Diffusion

Abstract A carboxylated nitrile rubber (XNBR) and a carboxylated SBR (XSBR) were mixed with zinc oxide particles of different specific surface areas (“S”, 35 m2/g; “M”, 3.5m2/g; “L”, 0.5 m2/g) and cure behavior at 165 ºC studied using oscillating disc rheometry. Without added zinc oxide, both raw rubbers slowly stiffen over many hours of heating. This is probably due to condensation of carboxyl groups to form anhydride crosslinks. XNBR compositions containing the finely divided “S” crosslink much more rapidly. Full cure is reached after about 10 minutes of heating. Cure rate decreases markedly as the specific surface area of the ZnO decreases. A composition containing “M” at twice stoichiometry requires about an hour to cure well, while with “L”, about 10 hours are required. In contrast, curing of the XSBR depends little on the specific surface area of the ZnO, either with “S” or “L”, curing is essentially complete after 30 minutes. After simply mixing ZnO into either rubber, it remains as a dispersed particulate. With XNBR, curing appears to be controlled by the rate of dissolution and diffusion of ZnO, while, with XSBR, reaction is not diffusion limited and may be confined to regions near particle surfaces.

scholarly journals Experimental and Simulation Studies on Adsorption and Diffusion Characteristics of Coalbed Methane

Energies ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3445 ◽  
Author(s):  
Donghyeon Kim ◽  
Youngjin Seo ◽  
Juhyun Kim ◽  
Jeongmin Han ◽  
Youngsoo Lee
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Coalbed Methane ◽  
Equilibrium Time ◽  
Diffusion Characteristics ◽  
Adsorbed Methane ◽  
Cbm Production ◽  
Lump Coal ◽  
And Diffusion

Coalbed methane (CBM) content is generally estimated using the isotherm theory between pressure and adsorbed amounts of methane. It usually determines the maximum content of adsorbed methane or storage capacity. However, CBM content obtained via laboratory experiment is not consistent with that in the in-situ state because samples are usually ground, which changes the specific surface area. In this study, the effect of the specific surface area relative to CBM content was investigated, and diffusion coefficients were estimated using equilibrium time analysis. The differences in adsorbed content with sample particle size allowed the determination of a specific surface area where gases can adsorb. Also, there was an equilibrium time difference between fine and lump coal, because more time is needed for the gas to diffuse through the coal matrix and adsorb onto the surface in lump coal. Based on this, we constructed a laboratory-scale simulation model, which matched with experimental results. Consequently, the diffusion coefficient, which is usually calculated through canister testing, can be easily obtained. These results stress that lump coal experiments and associated simulations are necessary for more reliable CBM production analysis.

Nanoporous zero-valent iron

2005 ◽  
Vol 20 (12) ◽  
pp. 3238-3243 ◽  
Author(s):  
Jiasheng Cao ◽  
Patrick Clasen ◽  
Wei-xian Zhang
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Performance Enhancement ◽  
Zero Valent Iron ◽  
Iron Particles ◽  
Surface Areas ◽  
Batch Tests ◽  
Resin Beads ◽  
Solid Iron

Hollow and nanoporous particles of zero-valent iron (ZVI) were prepared with template-directed synthesis. Polymer resin beads (0.4 mm diameter) were coated with nanoscale iron particles by reductive precipitation of ferrous iron [Fe(II)] with sodium borohydride. The resin was calcinated at 400 °C to produce hollow and nanoporous iron spheres. The nanoporous iron oxides were then reduced to metallic iron by hydrogen at 500 °C. Scanning electron microscope images of the reduced iron spheres showed that the particles were hollow. The shell thickness was approximately 5 μm and highly porous. Brunauer–Emmett–Teller specific surface area was 2100 m2/kg. In comparison, the theoretical specific surface area of solid iron particles of the same size is just 1.9 m2/kg. Batch tests showed that the surface area normalized reactivity of the porous particles were 14–31% higher than microscale iron particles with similar surface areas for the transformation of hexavalent chromium [Cr(VI)], azo dye Orange II {4-[(2-hydroxyl-1-naphthalenyl)azo]-benzenesulfonic acid monosodium}, and trichloroethene. The combined performance enhancement (larger surface area and higher surface activity) is significant (>1200 times).

Influence of Zinc Oxide Nanograins on Properties of Epoxidized Natural Rubber Vulcanizates

2017 ◽  
Vol 748 ◽  
pp. 79-83 ◽  
Author(s):  
Rudeerat Suntako
Keyword(s):  
Mechanical Properties ◽  
Zinc Oxide ◽  
Natural Rubber ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Epoxidized Natural Rubber ◽  
Precipitation Method ◽  
Cure Characteristics ◽  
Permanent Set

Zinc oxide (ZnO) nanograins are synthesized by precipitation method filled epoxidized natural rubber compared to conventional ZnO. The synthesized ZnO nanograins are characterized by X-ray diffraction and transmission electron microscopy and found that average primary size of ZnO synthesized around 40 nm and the specific surface area of 28.72 m2 g-1. Furthermore, the cure characteristics, rubber mechanical properties and permanent set were investigated. The obtained results are found that the ZnO nanograins significantly affected to cure characteristics, rubber mechanical properties and permanent set. This is due to small grain size and large specific surface area.

A Comparison of Methods for Determining Surface Areas of Carbon Black

1973 ◽  
Vol 46 (1) ◽  
pp. 192-203 ◽  
Author(s):  
R. A. Klyne ◽  
B. D. Simpson ◽  
M. L. Studebaker
Keyword(s):  
Carbon Black ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Surface Areas ◽  
Furnace Black ◽  
Area Increase ◽  
Experimental Errors ◽  
Specific Surface Areas ◽  
Surface Area Increase

Abstract 1. The various tint tests correlate with each other—it does not make much difference which of the three procedures is used. The discrimination between similar blacks is comparable. Specific surface areas obtained by the three methods are comparable and differences appear to be due to experimental errors. (Compare Figures 5–7). 2. Surface areas larger than some 90 to 100 m2/g cannot be reliably determined from tint strength measurements alone. 3. Structure exerts a pronounced effect on tint strength of furnace blacks, especially above 90 to 100 m2/g. Porosity and/or composition are apparently also variables which affect tinting strength. 4. Densichron reflectance on the dry carbon black can be used to estimate specific surface areas up to about 140 m2/g; but, since theabsoluteerrorincreases as the specific surface area increases, this method loses some of its reliability at values above about 110 m2/g. The relative error in reflectance determinations does not vary greatly over the furnace-black range. Densichron reflectance is influenced by composition, evidently due to composition-related differences in optical properties of the carbons. 5. In CTAB adsorption measurements, titration errors and handling errors tend to be rather constant for blacks of different surface area. Hence, CTAB permits better discrimination among blacks of small particle size. 6. The errors in Densichron reflectance surface area increase with specific surface area. Hence, the deviations between CTAB and reflectance surface area which are due to experimental error increase with the surface area of the sample.

Annealing of mesoporous silica loaded with silver nanoparticles within its pores from isothermal sorption

1998 ◽  
Vol 13 (10) ◽  
pp. 2888-2895 ◽  
Author(s):  
Weiping Cai ◽  
Lide Zhang ◽  
Huicai Zhong ◽  
Guoliang He
Keyword(s):  
Mesoporous Silica ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Ag Nanoparticles ◽  
Porous Silica ◽  
Pore Wall ◽  
Ag Particles ◽  
Real Value ◽  
And Diffusion

Influences of annealing on the structure of mesoporous silica loaded with silver (Ag) nanoparticles, and on the coarsening of Ag particles within pores of the host were investigated from isothermal sorption. Doping a small amount of Ag nanoparticles into pores of silica and subsequent annealing decreases the measured values of specific surface area and pore volume of porous silica significantly. This is attributed to the presence and coarsening of Ag particles within pores or channels between pores, which result in more and more isolated and unmeasured free spaces. The measured value of a specific surface area for the doped samples cannot represent the real value, which is, in fact, unable to be measured directly. During additional annealing, Ag particles within silica coarsen mainly according to the mechanism of formation of Ag adatoms on pore wall and diffusion of the adatoms along with pore walls. Only the larger particles located in the larger pores can continuously grow. The smaller particles and those located in the channels or pores with smaller dimension will disappear. The activation energy of the ripening process was estimated to be about 0.60 eV, and the migration barrier of Ag adatom on the pore wall of silica is about 0.10 eV.

scholarly journals A Case Study of Waste Scrap Tyre-Derived Carbon Black Tested for Nitrogen, Carbon Dioxide, and Cyclohexane Adsorption

Molecules ◽  
2020 ◽  
Vol 25 (19) ◽  
pp. 4445 ◽  
Author(s):  
Zuzana Jankovská ◽  
Marek Večeř ◽  
Ivan Koutník ◽  
Lenka Matějová
Keyword(s):  
Activated Carbon ◽  
Carbon Black ◽  
Specific Surface ◽  
Surface Area ◽  
Sorption Capacity ◽  
Specific Surface Area ◽  
Textural Properties ◽  
Pyrolytic Carbon ◽  
Surface Areas ◽  
Wide Range

Waste scrap tyres were thermally decomposed at the temperature of 600 °C and heating rate of 10 °C·min−1. Decomposition was followed by the TG analysis. The resulting pyrolytic carbon black was chemically activated by a KOH solution at 800 °C. Activated and non-activated carbon black were investigated using high pressure thermogravimetry, where adsorption isotherms of N2, CO2, and cyclohexane were determined. Isotherms were determined over a wide range of pressure, 0.03–4.5 MPa for N2 and 0.03–2 MPa for CO2. In non-activated carbon black, for the same pressure and temperature, a five times greater gas uptake of CO2 than N2 was determined. Contrary to non-activated carbon black, activated carbon black showed improved textural properties with a well-developed irregular mesoporous-macroporous structure with a significant amount of micropores. The sorption capacity of pyrolytic carbon black was also increased by activation. The uptake of CO2 was three times and for cyclohexane ten times higher in activated carbon black than in the non-activated one. Specific surface areas evaluated from linearized forms of Langmuir isotherm and the BET isotherm revealed that for both methods, the values are comparable for non-activated carbon black measured by CO2 and for activated carbon black measured by cyclohexane. It was found out that the N2 sorption capacity of carbon black depends only on its specific surface area size, contrary to CO2 sorption capacity, which is affected by both the size of specific surface area and the nature of carbon black.

scholarly journals W-Sn Mixed Oxides and ZnO to Detect NOx and Ozone in Atmosphere

Proceedings ◽  
2018 ◽  
Vol 2 (13) ◽  
pp. 836
Author(s):  
Ambra Fioravanti ◽  
Sara Morandi ◽  
Alessia Amodio ◽  
Mauro Mazzocchi ◽  
Michele Sacerdoti ◽  
...  
Keyword(s):  
Zinc Oxide ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Mixed Oxides ◽  
Gas Sensing ◽  
Molar Fraction ◽  
Functional Materials ◽  
X Ray Diffraction ◽  
X Ray

Thick films of zinc oxide (ZnO) in form of nanospheres or hexagonal prisms and of tungsten-tin (W-Sn) mixed oxides at nominal Sn molar fraction (0.1, 0.3 and 0.5) were prepared. The functional materials were synthesized and characterized by SEM and TEM, X-ray diffraction, specific surface area measurements, UV-Vis-NIR and IR spectroscopies. The gas sensing measurements highlighted that ZnO is more performant in form of nanoprisms, while W-Sn sensors offer a better response towards NOx and ozone with respect to pure WO3.

Experimental Studies of Carbon Electrodes With Various Surface Area for Li–O2 Batteries

2019 ◽  
Vol 16 (4) ◽  
Author(s):  
Fangzhou Wang ◽  
P. K. Kahol ◽  
Ram Gupta ◽  
Xianglin Li
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Discharge Capacity ◽  
Carbon Materials ◽  
High Specific Surface Area ◽  
Acetylene Black ◽  
Carbon Electrodes ◽  
Tea Leaves ◽  
Surface Areas

Li−O2 batteries with carbon electrodes made from three commercial carbons and carbon made from waste tea leaves are investigated in this study. The waste tea leaves are recycled from household tea leaves and activated using KOH. The carbon materials have various specific surface areas, and porous structures are characterized by the N2 adsorption/desorption. Vulcan XC 72 carbon shows a higher specific surface area (264.1 m2/g) than the acetylene black (76.5 m2/g) and Super P (60.9 m2/g). The activated tea leaves have an extremely high specific surface area of 2868.4 m2/g. First, we find that the commercial carbons achieve similar discharge capacities of ∼2.50 Ah/g at 0.5 mA/cm2. The micropores in carbon materials result in a high specific surface area but cannot help to achieve higher discharge capacity because it cannot accommodate the solid discharge product (Li2O2). Mixing the acetylene black and the Vulcan XC 72 improves the discharge capacity due to the optimized porous structure. The discharge capacity increases by 42% (from 2.73 ± 0.46 to 3.88 ± 0.22 Ah/g) at 0.5 mA/cm2 when the mass fraction of Vulcan XC 72 changes from 0 to 0.3. Second, the electrode made from activated tea leaves is demonstrated for the first time in Li−O2 batteries. Mixtures of activated tea leaves and acetylene black confirm that mixtures of carbon material with different specific surface areas can increase the discharge capacity. Moreover, carbon made from recycled tea leaves can reduce the cost of the electrode, making electrodes more economically achievable. This study practically enhances the discharge capacity of Li−O2 batteries using mixed carbons and provides a method for fabricating carbon electrodes with lower cost and better environmental friendliness.

Valorization of cellulose-doped lignin: application of cellulose-doped lignin-derived activated carbon in capacitors and investigation of its textural properties and electrochemical performance

2021 ◽  
Author(s):  
Liangcai Wang ◽  
Xin Feng ◽  
Huanhuan Ma ◽  
Jielong Wu ◽  
Yu Chen ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Specific Capacitance ◽  
Surface Area ◽  
Specific Surface Area ◽  
Wall Thickness ◽  
Textural Properties ◽  
Pore Wall ◽  
Surface Areas ◽  
Pore Wall Thickness

Abstract This work provides an idea for efficient and harmless utilization of lignin and further evaluated the textural properties of lignin-derived activated carbon/specific capacitance relationship. The yield of cellulose-doped apricot shell lignin (ASLC) was 30.42%. H3PO4/KOH was used to assist the preparation of ASLC-derived activated carbon (AAC) for capacitors. The specific surface areas of the as-obtained AAC-P-3 and AAC-K-2 were 1475.16 m2/g and 2136.56 m2/g, respectively. The specific capacitances of AAC-P-3 and AAC-K-2 were 169.14 F/g and 236.00 F/g, respectively, upon the current density of 0.50 A/g. In capacitors containing aqueous KOH as the electrolyte, the AR2 (0.983) between specific surface area and specific capacitance was highest, followed by the AR2 (0.978) between Vmicro/Vmeso and specific capacitance, the AR2 (0.975) between pore-wall thickness and specific capacitance. Consequently, the specific capacitances of the AACs depend not only the specific surface area, but also on the Vmicro/Vmeso, pore-wall thickness, and Vmicro.

Sign in / Sign up

Export Citation Format

Share Document