Sulfate Formation During Corrosion of Copper Alloy Objects

1992 ◽  
Vol 267 ◽  
Author(s):  
Michael B. McNeil ◽  
D. W. Mohr

ABSTRACTThe copper sulfate minerals chalcanthite (CuSO4.5H20), antlerite (Cu3SO4(OH)4), and brochantite (Cu4SO4(OH)6) are observed as corrosion products on copper alloy objects such as statues which are exposed to weathering. The usual product in aqueous corrosion is brochantite, though posnjakite (Cu4SO4(OH)6H20) is also known. No copper sulfate mineral is commonly found in artifacts recovered from near-surface burial. These observations can be explained in terms of stability diagrams and microbiological activity.

2021 ◽  
pp. 1-30
Author(s):  
Oleg I. Siidra ◽  
Artem S. Borisov ◽  
Dmitri O. Charkin ◽  
Wulf Depmeier ◽  
Natalia V. Platonova

2014 ◽  
Vol 2 (2) ◽  
Author(s):  
Olta Çakaj ◽  
Edlira Duka ◽  
Zamir Tafilica ◽  
Frederik Stamati ◽  
Nikolla Civici ◽  
...  

This study was performed to determine the chemical elements used to produce ancient metallic alloys and to understand the manufacture technique of three archaeological founds. It also presents an evaluation method of the objects’ authenticity based on the observation of the corrosion products. This article also includes three ornamental accessories ca. VII-IV century BC found in the vicinity of Shkodra (Albania). A necklace, a belt application and a button are examined using X ray fluorescence (XRF) to determine the chemical composition and optical microscopy (OM) with reflected and polarised light in order to study the microstructure and the corrosion products. From the XRF results all the objects are bronze, copper-tin and copper-tin-lead alloys. After the OM analysis they are authentic objects (not fake replicas) and might have been produced after a casting process in moulds.


2018 ◽  
Vol 143 ◽  
pp. 400-409 ◽  
Author(s):  
A. Inberg ◽  
D. Ashkenazi ◽  
M. Cohen ◽  
N. Iddan ◽  
D. Cvikel

2010 ◽  
Vol 20 (2) ◽  
pp. 82-89
Author(s):  
Sang-Beoum Kim ◽  
Hyun-Cheol Kim ◽  
Hyung-Ho Park

Minerals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 228
Author(s):  
Jan Parafiniuk ◽  
Rafał Siuda

The subject of this work is the assemblage of anhydrous sulfate minerals formed on burning coal-heaps. Three burning heaps located in the Upper Silesian coal basin in Czerwionka-Leszczyny, Radlin and Rydułtowy near Rybnik were selected for the research. The occurrence of godovikovite, millosevichite, steklite and an unnamed MgSO4, sometimes accompanied by subordinate admixtures of mikasaite, sabieite, efremovite, langbeinite and aphthitalite has been recorded from these locations. Occasionally they form monomineral aggregates, but usually occur as mixtures practically impossible to separate. The minerals form microcrystalline masses with a characteristic vesicular structure resembling a solidified foam or pumice. The sulfates crystallize from hot fire gases, similar to high temperature volcanic exhalations. The gases transport volatile components from the center of the fire but their chemical compositions are not yet known. Their cooling in the near-surface part of the heap results in condensation from the vapors as viscous liquid mass, from which the investigated minerals then crystallize. Their crystallization temperatures can be estimated from direct measurements of the temperatures of sulfate accumulation in the burning dumps and studies of their thermal decomposition. Millosevichite and steklite crystallize in the temperature range of 510–650 °C, MgSO4 forms at 510–600 °C and godovikovite in the slightly lower range of 280–450 (546) °C. These values are higher than those previously reported.


1988 ◽  
Vol 62 (01) ◽  
pp. 1-8 ◽  
Author(s):  
Ronald E. Martin

The utility of benthic foraminifera in bathymetric interpretation of clastic depositional environments is well established. In contrast, bathymetric distribution of benthic foraminifera in deep-water carbonate environments has been largely neglected. Approximately 260 species and morphotypes of benthic foraminifera were identified from 12 piston core tops and grab samples collected along two traverses 25 km apart across the northern windward margin of Little Bahama Bank at depths of 275-1,135 m. Certain species and operational taxonomic groups of benthic foraminifera correspond to major near-surface sedimentary facies of the windward margin of Little Bahama Bank and serve as reliable depth indicators. Globocassidulina subglobosa, Cibicides rugosus, and Cibicides wuellerstorfi are all reliable depth indicators, being most abundant at depths >1,000 m, and are found in lower slope periplatform aprons, which are primarily comprised of sediment gravity flows. Reef-dwelling peneroplids and soritids (suborder Miliolina) and rotaliines (suborder Rotaliina) are most abundant at depths <300 m, reflecting downslope bottom transport in proximity to bank-margin reefs. Small miliolines, rosalinids, and discorbids are abundant in periplatform ooze at depths <300 m and are winnowed from the carbonate platform. Increased variation in assemblage diversity below 900 m reflects mixing of shallow- and deep-water species by sediment gravity flows.


Author(s):  
P.M. Rice ◽  
MJ. Kim ◽  
R.W. Carpenter

Extrinsic gettering of Cu on near-surface dislocations in Si has been the topic of recent investigation. It was shown that the Cu precipitated hetergeneously on dislocations as Cu silicide along with voids, and also with a secondary planar precipitate of unknown composition. Here we report the results of investigations of the sense of the strain fields about the large (~100 nm) silicide precipitates, and further analysis of the small (~10-20 nm) planar precipitates.Numerous dark field images were analyzed in accordance with Ashby and Brown's criteria for determining the sense of the strain fields about precipitates. While the situation is complicated by the presence of dislocations and secondary precipitates, micrographs like those shown in Fig. 1(a) and 1(b) tend to show anomalously wide strain fields with the dark side on the side of negative g, indicating the strain fields about the silicide precipitates are vacancy in nature. This is in conflict with information reported on the η'' phase (the Cu silicide phase presumed to precipitate within the bulk) whose interstitial strain field is considered responsible for the interstitial Si atoms which cause the bounding dislocation to expand during star colony growth.


Author(s):  
Naresh N. Thadhani ◽  
Thad Vreeland ◽  
Thomas J. Ahrens

A spherically-shaped, microcrystalline Ni-Ti alloy powder having fairly nonhomogeneous particle size distribution and chemical composition was consolidated with shock input energy of 316 kJ/kg. In the process of consolidation, shock energy is preferentially input at particle surfaces, resulting in melting of near-surface material and interparticle welding. The Ni-Ti powder particles were 2-60 μm in diameter (Fig. 1). About 30-40% of the powder particles were Ni-65wt% and balance were Ni-45wt%Ti (estimated by EMPA).Upon shock compaction, the two phase Ni-Ti powder particles were bonded together by the interparticle melt which rapidly solidified, usually to amorphous material. Fig. 2 is an optical micrograph (in plane of shock) of the consolidated Ni-Ti alloy powder, showing the particles with different etching contrast.


Author(s):  
R.C. Dickenson ◽  
K.R. Lawless

In thermal oxidation studies, the structure of the oxide-metal interface and the near-surface region is of great importance. A technique has been developed for constructing cross-sectional samples of oxidized aluminum alloys, which reveal these regions. The specimen preparation procedure is as follows: An ultra-sonic drill is used to cut a 3mm diameter disc from a 1.0mm thick sheet of the material. The disc is mounted on a brass block with low-melting wax, and a 1.0mm hole is drilled in the disc using a #60 drill bit. The drill is positioned so that the edge of the hole is tangent to the center of the disc (Fig. 1) . The disc is removed from the mount and cleaned with acetone to remove any traces of wax. To remove the cold-worked layer from the surface of the hole, the disc is placed in a standard sample holder for a Tenupol electropolisher so that the hole is in the center of the area to be polished.


Sign in / Sign up

Export Citation Format

Share Document