Deposition of Gan Films Using Seeded Supersonic Jets

1995 ◽  
Vol 388 ◽  
Author(s):  
H. Henry Lamb ◽  
Ken K. Lai ◽  
Victor Torres ◽  
Robert F. Davis
Keyword(s):  
High Energy ◽  
Flow Ratio ◽  
X Ray Diffraction ◽  
Dissociative Chemisorption ◽  
Free Jets ◽  
X Ray ◽  
Nozzle Temperature ◽  
Incident Kinetic Energy ◽  
Rate Limiting ◽  
Substrate Temperatures

AbstractGaN films were deposited on sapphire (0001) from triethylgallium (TEG) and NH3 seeded in separate He free jets. as the dissociative chemisorption of NH3 is expected to be rate-limiting in GaN growth, the NH3/He nozzle temperature was varied to control the incident kinetic energy of the NH3 molecules. Using an NH3/TEG flow ratio of 205 and an NH3/He nozzle temperature of 400°C, stoichiometric films were deposited at substrate temperatures ≥530°C. Scanning electron microscopy revealed that films deposited at 580°C are polycrystalline α-GaN with randomly oriented 0.5-μm grains. Films with a closely similar morphology are deposited by using an NH3/He nozzle temperature of 90°C. IN contrast, films deposited at 580°C using an NH3/He nozzle temperature of 510°C consist of whiskers (aspect ratio = c A. 4) which exhibit a-GaN (0001)/sapphire (0001) heteroepitaxy, as evidenced by X-ray diffraction and reflection high-energy electron diffraction.

Epitaxial growth of Cr [001] on LiF [001]

1989 ◽  
Vol 160 ◽  
Author(s):  
J. Mattson ◽  
M. B. Brodsky ◽  
J. Ketterson ◽  
H. You
Keyword(s):  
Thin Films ◽  
Electron Diffraction ◽  
Epitaxial Growth ◽  
High Energy ◽  
High Energy Electron ◽  
X Ray Diffraction ◽  
X Ray ◽  
Substrate Temperatures ◽  
Deposition Conditions

AbstractWe report X-ray diffraction and in-situ RHEED( Reflection High Energy Electron Diffraction) measurements on Cr thin films deposited on LiF[001] single crystal substrates for thicknesses up to 300 nm and for substrate temperatures from 30 to 450°C. From these measurements we determine the range of deposition conditions necessary for epitaxial growth and the stress in these films as a function of film thickness.

Characterizations of Synthetic 8mol% YSZ with Comparison to 3mol %YSZ for HT-SOFC

2020 ◽  
Vol 38 (4A) ◽  
pp. 491-500
Author(s):  
Abeer F. Al-Attar ◽  
Saad B. H. Farid ◽  
Fadhil A. Hashim
Keyword(s):  
Ionic Conductivity ◽  
Electrochemical Impedance ◽  
Structural Information ◽  
Impedance Analysis ◽  
High Energy ◽  
Yttria Stabilized Zirconia ◽  
X Ray Diffraction ◽  
Stabilized Zirconia ◽  
Powder Morphology ◽  
X Ray

In this work, Yttria (Y2O3) was successfully doped into tetragonal 3mol% yttria stabilized Zirconia (3YSZ) by high energy-mechanical milling to synthesize 8mol% yttria stabilized Zirconia (8YSZ) used as an electrolyte for high temperature solid oxide fuel cells (HT-SOFC). This work aims to evaluate the densification and ionic conductivity of the sintered electrolytes at 1650°C. The bulk density was measured according to ASTM C373-17. The powder morphology and the microstructure of the sintered electrolytes were analyzed via Field Emission Scanning Electron Microscopy (FESEM). The chemical analysis was obtained with Energy-dispersive X-ray spectroscopy (EDS). Also, X-ray diffraction (XRD) was used to obtain structural information of the starting materials and the sintered electrolytes. The ionic conductivity was obtained through electrochemical impedance spectroscopy (EIS) in the air as a function of temperatures at a frequency range of 100(mHz)-100(kHz). It is found that the 3YSZ has a higher density than the 8YSZ. The impedance analysis showed that the ionic conductivity of the prepared 8YSZ at 800°C is0.906 (S.cm) and it was 0.214(S.cm) of the 3YSZ. Besides, 8YSZ has a lower activation energy 0.774(eV) than that of the 3YSZ 0.901(eV). Thus, the prepared 8YSZ can be nominated as an electrolyte for the HT-SOFC.

scholarly journals In-Situ High-Energy X-ray Diffraction Study of Austenite Decomposition During Rapid Cooling and Isothermal Holding in Two HSLA Steels

2021 ◽  
Vol 52 (5) ◽  
pp. 1812-1825
Author(s):  
Sen Lin ◽  
Ulrika Borggren ◽  
Andreas Stark ◽  
Annika Borgenstam ◽  
Wangzhong Mu ◽  
...  
Keyword(s):  
Isothermal Holding ◽  
Weight Percent ◽  
High Energy ◽  
Decomposition Kinetics ◽  
Bainitic Transformation ◽  
Austenite Decomposition ◽  
X Ray Diffraction ◽  
Rapid Cooling ◽  
X Ray

AbstractIn-situ high-energy X-ray diffraction experiments with high temporal resolution during rapid cooling (280 °C s−1) and isothermal heat treatments (at 450 °C, 500 °C, and 550 °C for 30 minutes) were performed to study austenite decomposition in two commercial high-strength low-alloy steels. The rapid phase transformations occurring in these types of steels are investigated for the first time in-situ, aiding a detailed analysis of the austenite decomposition kinetics. For the low hardenability steel with main composition Fe-0.08C-1.7Mn-0.403Si-0.303Cr in weight percent, austenite decomposition to polygonal ferrite and bainite occurs already during the initial cooling. However, for the high hardenability steel with main composition Fe-0.08C-1.79Mn-0.182Si-0.757Cr-0.094Mo in weight percent, the austenite decomposition kinetics is retarded, chiefly by the Mo addition, and therefore mainly bainitic transformation occurs during isothermal holding; the bainitic transformation rate at the isothermal holding is clearly enhanced by lowered temperature from 550 °C to 500 °C and 450 °C. During prolonged isothermal holding, carbide formation leads to decreased austenite carbon content and promotes continued bainitic ferrite formation. Moreover, at prolonged isothermal holding at higher temperatures some degenerate pearlite form.

scholarly journals Spatially Resolved Forming Mechanisms Detection in Single Point Incremental Forming Using Synchrotron Based Texture Analysis

2021 ◽  
Author(s):  
Mateus Dobecki ◽  
Alexander Poeche ◽  
Walter Reimers
Keyword(s):  
Texture Analysis ◽  
Incremental Forming ◽  
Single Point ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Forming Mechanism ◽  
Spatially Resolved ◽  
Step Down ◽  
Stress States

AbstractDespite the ongoing success of understanding the deformation states in sheets manufactured by single-point incremental forming (SPIF), the unawareness of the spatially resolved influence of the forming mechanisms on the residual stress states of incrementally formed sheet metal parts impedes their application-optimized use. In this study, a well-founded experimental proof of the occurring forming mechanisms shear, bending and stretching is presented using spatially resolved, high-energy synchrotron x-ray diffraction-based texture analysis in transmission mode. The measuring method allows even near-surface areas to be examined without any impairment of microstructural influences due to tribological reactions. The depth-resolved texture evolution for different sets of forming parameters offers insights into the forming mechanisms acting in SPIF. Therefore, the forming mechanisms are triggered explicitly by adjusting the vertical step-down increment Δz for groove, plate and truncated cone geometries. The texture analysis reveals that the process parameters and the specimen geometries used lead to characteristic changes in the crystallites’ orientation distribution in the formed parts due to plastic deformation. These forming-induced reorientations of the crystallites could be assigned to the forming mechanisms by means of defined reference states. It was found that for groove, plate and truncated cone geometries, a decreasing magnitude of step-down increments leads to a more pronounced shear deformation, which causes an increasing work hardening especially at the tool contact area of the formed parts. Larger step-down increments, on the other hand, induce a greater bending deformation. The plastic deformation by bending leads to a complex stress field that involves alternating residual tensile stresses on the tool and residual compressive stresses on the tool-averted side incrementally formed sheets. The present study demonstrates the potential of high-energy synchrotron x-ray diffraction for the spatially resolved forming mechanism research in SPIF. Controlling the residual stress states by optimizing the process parameters necessitates knowledge of the fundamental forming mechanism action.

scholarly journals Dislocation densities in a low-carbon steel during martensite transformation determined by in situ high energy X-Ray diffraction

2021 ◽  
Vol 800 ◽  
pp. 140249
Author(s):  
Juan Macchi ◽  
Steve Gaudez ◽  
Guillaume Geandier ◽  
Julien Teixeira ◽  
Sabine Denis ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Martensite Transformation ◽  
Low Carbon Steel ◽  
High Energy ◽  
Low Carbon ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dislocation Densities

scholarly journals Thermal expansion of La-based BMG studied by in situ high-energy X-ray diffraction

2010 ◽  
Vol 504 ◽  
pp. S155-S158 ◽  
Author(s):  
J. Bednarcik ◽  
C. Curfs ◽  
M. Sikorski ◽  
H. Franz ◽  
J.Z. Jiang
Keyword(s):  
Thermal Expansion ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray
Sign in / Sign up

Export Citation Format

Share Document