Germanium Nanostructures Fabricated by PLD

1998 ◽  
Vol 536 ◽  
Author(s):  
K. M. Hassan ◽  
A. K. Sharma ◽  
J. Narayan ◽  
J. F. Muth ◽  
C. W. Teng

AbstractQuantum confined nanostructures of semiconductors such as Ge and Si are being actively studied due to their interesting optical and electronic transport properties. We fabricated Ge nanostructures buried in the matrix of polycrystalline-AIN grown on Si(111) by pulsed laser deposition at lower substrate temperatures than that used in previous studies. The characterization of these structures was performed using high resolution transmission electron microscopy (HRTEM), photoluminescence and Raman spectroscopy. HRTEM observations show that the Ge islands are single crystal with a pyramidal shape. The average size of Ge islands was determined to be 15 nm, considerably smaller than that produced by other techniques. The Raman spectrum reveals a peak downward shift, upto 295 cm−1, of the Ge-Ge mode caused by quantum confinement in the Ge-dots. Photoluminescence (PL) was observed both with a single layer of Ge nanodots embedded in the AlN matrix and from ten layers of dots interspersed with AIN. The PL of the dots was blue shifted by ˜0.266 eV from the bulk Ge value of 0.73 eV at 77 K, resulting in a distinct peak at ˜1.0 eV. The full width at half maximum (FWHM) of the peak was 13 meV, for the single layer and 8 meV for the ten layered sample, indicating that the Ge nanodots are fairly uniform in size, which was found to be consistent with our HRTEM results. The importance of pulsed laser deposition (PLD) in fabricating novel nanostructures is discussed.

2000 ◽  
Vol 616 ◽  
Author(s):  
J.S. Pelt ◽  
R. Magahñ;a ◽  
M.E. Ramsey ◽  
E. Poindexter ◽  
S. Atwell ◽  
...  

AbstractThere is a great deal of interest in thin film deposition techniques which can achieve good crystal quality at low substrate temperatures. Pulsed laser deposition (PLD), well-known as a reliable technique for fabrication of high critical temperature superconductor thin films, has a number of characteristics which may make it suitable for such applications. In particular, PLD is characterized by a relatively large average species energy, which can be controlled by the laser fluence at the target. This paper describes the growth of silicon on silicon films using PLD over substrate temperatures between 500 and 700 °C, and in-situ characterization using reflection high-energy electron diffraction (RHEED). Transmission electron microscopy confirms the growth of single crystal oriented films, and atomic force microscopy indicates smooth films with an rms surface roughness of less than 2 Å


2011 ◽  
Vol 01 (03) ◽  
pp. 363-367 ◽  
Author(s):  
HONG LIU ◽  
JIANGUO ZHU ◽  
DINGQUAN XIAO

A single-crystalline, crack-free, epitaxial (100)c LaFeO3 films were in situ grown by pulsed laser deposition on (100) SrTiO3 substrates. X-ray diffraction, atomic force microscopy and transmission electron microscopy reveal that the LaFeO3 films have high crystalline quality, a very smooth surface, and an atomically sharp LaFeO3/SrTiO3 interface. The magnetic properties of the LaFeO3 films were obtained by a superconducting quantum interference device magnetometry. The saturated magnetization and coercive field of LaFeO3 films are 14 emu/cm3 and 600 Oe, respectively.


2008 ◽  
Vol 8 (5) ◽  
pp. 2575-2577 ◽  
Author(s):  
Shubra Singh ◽  
M. S. Ramachandra Rao

Undoped ZnO films were deposited using pulsed laser deposition technique on Si and glass substrates in different O2 partial pressures (ranging from 10−5 mbar to 3 mbar) and substrate temperatures. When the substrate temperature is 500 °C and O2 partial pressure (pp) ∼ 3 mbar, randomly oriented ZnO hexagons were observed on glass substrate, whereas, dense ZnO hexagonal rod like structures (diameter ranging from 200–500 nm) were observed on Si substrate. The photoluminescence (PL) characterization of ZnO film grown on Si exhibited an intense defect free narrow excitonic emission in the UV region (Full width half maximum (FWHM) ∼ 11.26 nm) as compared to broad emission (FWHM ∼ 57.06 nm) from that grown on glass. The parent film emission was found to shift from UV to blue region on doping ZnO with Vanadium.


Author(s):  
Ahmed Kamal ◽  
Hassan Abu Bakr ◽  
Ziyang Wang ◽  
H. El Samman ◽  
Paolo Fiorini ◽  
...  

The main objective of this work is to investigate the possibility of preparing bismuth telluride thin films using pulsed laser deposition. The effect of varying the deposition pressure, laser fluence, and the deposition temperature on the surface roughness, film composition, grain microstructure and electrical resistivity is analyzed using, scanning electron microscopy, atomic force microscopy, X-ray fluorescence, transmission electron microscopy, and four point probe measurements. It is demonstrated that relatively smooth films can be deposited at a laser flounce of 0.6 J/cm2 and using argon as a background gas at 10−1 mbar. On the other hand, resistivities as low as 2 mΩ.cm can be obtained by either depositing the film at 200°C, or by post-laser annealing films deposited at room temperature.


2005 ◽  
Vol 900 ◽  
Author(s):  
Md. Mosharraf Hossain Bhuiyan ◽  
Tsuyoshi Ueda ◽  
Hiroshi Shinguu ◽  
Tomoaki Ikegami ◽  
Kenji Ebihara

ABSTRACTGas sensors based on WO3 thin films doped with platinum (Pt) or palladium (Pd) were prepared by KrF excimer pulsed laser deposition method combined with dc sputtering. The films were deposited on silicon, quartz and Al2O3 sensor substrate with Pt interdigital electrodes at various substrate temperatures from 300°C to 500 °C, and oxygen pressures from 100 mTorr to 300 m Torr, respectively during the deposition. The morphology and structure of the films were examined by AFM and XRD. The sensor property of the WO3−x thin films was measured by the two terminal resistance method at operating temperatures of 25 °C to 400 °C. The sensitivity of the WO3 thin film gas sensors with doping (platinum or palladium) was found to be higher than that of undoped WO3 thin films gas sensors. The sensitivity of the pt doped WO3 films to different concentration of NO gas was examined and the sensitivity was found to be increased with increasing NO gas concentration.


2000 ◽  
Vol 15 (7) ◽  
pp. 1524-1527 ◽  
Author(s):  
Y. H. Li ◽  
L. Salamanca-Riba ◽  
Y. Zhao ◽  
S. B. Ogale ◽  
R. Ramesh ◽  
...  

La0.67Sr0.33MnO3 thin films were grown on LaAlO3 substrate in vacuum using pulsed laser deposition to investigate the effect of changing oxygen content. Transmission electron microscopy studies showed that the epitaxial (La0.67Sr0.33)2MnO4 phase with K2NiF4 structure formed unexpectedly as a matrix with a square-shaped nanometer-sized MnO phase distributed in a regular pattern throughout the whole film like self-assembled quantum dots. The MnO phase grew epitaxially from the LaAlO3 substrate to the top of the film with no outgrowth. High-resolution image simulation indicated that Sr ions take up only positions in every other La layer in the (La0.67Sr0.33)2MnO4 structure. Basing our theory on the composition and structure of the matrix phase, we propose that it is possibly electron-doped with a mixed valence of Mn2+/Mn3+ instead of the Mn3+/Mn4+ as in the hole-doped case.


1995 ◽  
Vol 385 ◽  
Author(s):  
M. Grant Norton ◽  
Wenbiao Jiang ◽  
J. Thomas Dickinson

ABSTRACTThin films of polytetrafluoroethylene have been formed by the pulsed-laser deposition technique. The structure of the films was found to be dependent upon the substrate temperature during deposition. At substrate temperatures from room temperature to 200°C the films were determined, by transmission electron microscopy and X-ray diffraction techniques, to be amorphous. Films formed at higher substrate temperatures were found to contain both amorphous and crystalline components. The data for the crystalline component is consistent with it being highly ordered with the long helical molecular chains aligned parallel to the film-substrate interface plane. The maximum amount of crystalline material occurred when the substrate temperature was close to the melting temperature of the polymer.


2021 ◽  
Vol 127 ◽  
pp. 105716
Author(s):  
Tianzhen Guo ◽  
Dan Wang ◽  
Yajun Yang ◽  
Xiaoyong Xiong ◽  
Kelin Li ◽  
...  

2010 ◽  
Vol 75 ◽  
pp. 202-207
Author(s):  
Victor Ríos ◽  
Elvia Díaz-Valdés ◽  
Jorge Ricardo Aguilar ◽  
T.G. Kryshtab ◽  
Ciro Falcony

Bi-Pb-Sr-Ca-Cu-O (BPSCCO) and Bi-Pb-Sb-Sr-Ca-Cu-O (BPSSCCO) thin films were grown on MgO single crystal substrates by pulsed laser deposition. The deposition was carried out at room temperature during 90 minutes. A Nd:YAG excimer laser ( = 355 nm) with a 2 J/pulse energy density operated at 30 Hz was used. The distance between the target and substrate was kept constant at 4,5 cm. Nominal composition of the targets was Bi1,6Pb0,4Sr2Ca2Cu3O and Bi1,6Pb0,4Sb0,1Sr2Ca2Cu3OSuperconducting targets were prepared following a state solid reaction. As-grown films were annealed at different conditions. As-grown and annealed films were characterized by XRD, FTIR, and SEM. The films were prepared applying an experimental design. The relationship among deposition parameters and their effect on the formation of superconducting Bi-system crystalline phases was studied.


Sign in / Sign up

Export Citation Format

Share Document