Effects on CO and CO2 Emissions by Direct Hydrogen Substitution in a Compression Ignition Engine

2021 ◽  
Vol 15 (9) ◽  
pp. 504
Author(s):  
Carlos Pardo García ◽  
Jhon Antuny Pabon ◽  
Marlen Fonseca Vigoya
Keyword(s):  
Co2 Emissions ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Hydrogen Substitution

scholarly journals Effect of compression ignition engine preheating on its performance under cold start conditions

2021 ◽  
Author(s):  
Michał Gęca ◽  
Gojmir Radica
Keyword(s):  
Fuel Consumption ◽  
Co2 Emissions ◽  
Cooling System ◽  
Combustion Engine ◽  
Renewable Energy Sources ◽  
Cold Start ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Electric System ◽  
Driving Conditions

This paper examines the effect of an external preheating system for an internal combustion engine on fuel consumption, CO2 emissions, and cabin temperature of a Euro4 vehicle. A 1 kW electric system powered by 220 V was installed in series in the cooling system of a vehicle with a compression-ignition engine of 2.5 dm3 capacity. The tests were carried out in simulated urban driving conditions (distance of 4.2 km), extra-urban driving conditions (distance of 17 km), and during idling at cold-start temperatures ranging from -10 oC to 2 oC. Preheating the engine under simulated city conditions reduces fuel consumption by 2.64 dm3/100 km and increases the supply air temperature immediately after engine start-up. Due to the preheater being powered from an external power grid, the cost per trip and total CO2 emissions are increased. Assuming renewable energy sources, CO2 emissions would be reduced the most for the stationary tests after engine preheating. In contrast, emissions would be reduced the least for extra-urban driving.

Pollutant emissions investigation in a compression ignition engine during warm-up time

2017 ◽  
Author(s):  
Naiara Lima Costa ◽  
Ramon Eduardo Pereira Silva ◽  
Letícia Schneider Ferrari
Keyword(s):  
Pollutant Emissions ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Warm Up

scholarly journals An Experimental Investigation on the Effect of Ferrous Ferric Oxide Nano-Additive and Chicken Fat Methyl Ester on Performance and Emission Characteristics of Compression Ignition Engine

Symmetry ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 265
Author(s):  
Ameer Suhel ◽  
Norwazan Abdul Rahim ◽  
Mohd Rosdzimin Abdul Rahman ◽  
Khairol Amali Bin Ahmad ◽  
Yew Heng Teoh ◽  
...  
Keyword(s):  
Methyl Ester ◽  
Ferric Oxide ◽  
Fossil Fuels ◽  
Specific Energy Consumption ◽  
Experimental Results ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Chicken Fat

In recent years, industries have been investing to develop a potential alternative fuel to substitute the depleting fossil fuels which emit noxious emissions. Present work investigated the effect of ferrous ferric oxide nano-additive on performance and emission parameters of compression ignition engine fuelled with chicken fat methyl ester blends. The nano-additive was included with various methyl ester blends at different ppm of 50, 100, and 150 through the ultrasonication process. Probe sonicator was utilized for nano-fuel preparation to inhibit the formation of agglomeration of nanoparticles in base fuel. Experimental results revealed that the addition of 100 ppm dosage of ferrous ferric oxide nanoparticles in blends significantly improves the combustion performance and substantially decrease the pernicious emissions of the engine. It is also found from an experimental results analysis that brake thermal efficiency (BTE) improved by 4.84%, a reduction in brake specific fuel consumption (BSFC) by 10.44%, brake specific energy consumption (BSEC) by 9.44%, exhaust gas temperature (EGT) by 19.47%, carbon monoxides (CO) by 53.22%, unburned hydrocarbon (UHC) by 21.73%, nitrogen oxides (NOx) by 15.39%, and smoke by 14.73% for the nano-fuel B20FFO100 blend. By seeing of analysis, it is concluded that the doping of ferrous ferric oxide nano-additive in chicken fat methyl ester blends shows an overall development in engine characteristics.

Analysis of temperature and altitude effects on the Global Energy Balance during WLTC

2021 ◽  
pp. 146808742110342
Author(s):  
Francisco Payri ◽  
Jaime Martín ◽  
Francisco José Arnau ◽  
Sushma Artham
Keyword(s):  
Energy Balance ◽  
Ambient Temperature ◽  
Fuel Consumption ◽  
Experimental Measurements ◽  
Compression Ignition ◽  
Oil Viscosity ◽  
Compression Ignition Engine ◽  
Global Energy ◽  
Global Energy Balance ◽  
L Compression

In this work, the Global Energy Balance (GEB) of a 1.6 L compression ignition engine is analyzed during WLTC using a combination of experimental measurements and simulations, by means of a Virtual Engine. The energy split considers all the relevant energy terms at two starting temperatures (20°C and 7°C) and two altitudes (0 and 1000 m). It is shown that reducing ambient temperature from 20°C to −7°C decreases brake efficiency by 1% and increases fuel consumption by 4%, mainly because of the higher friction due to the higher oil viscosity, while the effect of increasing altitude 1000 m decreases brake efficiency by 0.8% and increases fuel consumption by 2.5% in the WLTC mainly due to the change in pumping. In addition, GEB shows that ambient temperature is affecting exhaust enthalpy by 4.5%, heat rejection to coolant by 2%, and heat accumulated in the block by 2.5%, while altitude does not show any remarkable variations other than pumping and break power.

scholarly journals Effect of Injection Timing and Injection Duration of Manifold Injected Fuels in Reactivity Controlled Compression Ignition Engine Operated with Renewable Fuels

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4621
Author(s):  
P. A. Harari ◽  
N. R. Banapurmath ◽  
V. S. Yaliwal ◽  
T. M. Yunus Khan ◽  
Irfan Anjum Badruddin ◽  
...  
Keyword(s):  
Nitric Oxide ◽  
Injection Timing ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Compression Ignition Engine ◽  
Compressed Natural Gas ◽  
Reactivity Controlled Compression Ignition ◽  
Brake Thermal Efficiency ◽  
Injection Duration ◽  
Fuel Mixtures

In the current work, an effort is made to study the influence of injection timing (IT) and injection duration (ID) of manifold injected fuels (MIF) in the reactivity controlled compression ignition (RCCI) engine. Compressed natural gas (CNG) and compressed biogas (CBG) are used as the MIF along with diesel and blends of Thevetia Peruviana methyl ester (TPME) are used as the direct injected fuels (DIF). The ITs of the MIF that were studied includes 45°ATDC, 50°ATDC, and 55°ATDC. Also, present study includes impact of various IDs of the MIF such as 3, 6, and 9 ms on RCCI mode of combustion. The complete experimental work is conducted at 75% of rated power. The results show that among the different ITs studied, the D+CNG mixture exhibits higher brake thermal efficiency (BTE), about 29.32% is observed at 50° ATDC IT, which is about 1.77, 3.58, 5.56, 7.51, and 8.54% higher than D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. The highest BTE, about 30.25%, is found for the D+CNG fuel combination at 6 ms ID, which is about 1.69, 3.48, 5.32%, 7.24, and 9.16% higher as compared with the D+CBG, B20+CNG, B20+CBG, B100+CNG, and B100+CBG fuel combinations. At all ITs and IDs, higher emissions of nitric oxide (NOx) along with lower emissions of smoke, carbon monoxide (CO), and hydrocarbon (HC) are found for D+CNG mixture as related to other fuel mixtures. At all ITs and IDs, D+CNG gives higher In-cylinder pressure (ICP) and heat release rate (HRR) as compared with other fuel combinations.

Sign in / Sign up

Export Citation Format

Share Document