Properties of drying shrinkage cracking of concrete containing fly ash as partial replacement of fine aggregate

2010 ◽  
Vol 62 (6) ◽  
pp. 427-433 ◽  
Author(s):  
T. Seo ◽  
M. Lee ◽  
C. Choi ◽  
Y. Ohno
Keyword(s):  
Fly Ash ◽  
Drying Shrinkage ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Shrinkage Cracking

scholarly journals Long-Term Physical and Mechanical Properties and Microstructures of Fly-Ash-Based Geopolymer Composite Incorporating Carbide Slag

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6692
Author(s):  
Xianhui Zhao ◽  
Haoyu Wang ◽  
Linlin Jiang ◽  
Lingchao Meng ◽  
Boyu Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fly Ash ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Drying Shrinkage ◽  
Fine Aggregate ◽  
Property Development ◽  
Industrial Solid Waste ◽  
Carbide Slag

The long-term property development of fly ash (FA)-based geopolymer (FA−GEO) incorporating industrial solid waste carbide slag (CS) for up to 360 d is still unclear. The objective of this study was to investigate the fresh, physical, and mechanical properties and microstructures of FA−GEO composites with CS and to evaluate the effects of CS when the composites were cured for 360 d. FA−GEO composites with CS were manufactured using FA (as an aluminosilicate precursor), CS (as a calcium additive), NaOH solution (as an alkali activator), and standard sand (as a fine aggregate). The fresh property and long-term physical properties were measured, including fluidity, bulk density, porosity, and drying shrinkage. The flexural and compressive strengths at 60 d and 360 d were tested. Furthermore, the microstructures and gel products were characterized by scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS). The results show that the additional 20.0% CS reduces the fluidity and increases the conductivity of FA−GEO composites. Bulk densities were decreased, porosities were increased, and drying shrinkages were decreased as the CS content was increased from 0.0% to 20.0% at 360 d. Room temperature is a better curing condition to obtain a higher long-term mechanical strength. The addition of 20.0% CS is more beneficial to the improvement of long-term flexural strength and toughness at room temperature. The gel products in CS−FA−GEO with 20.0% CS are mainly determined as the mixtures of sodium aluminosilicate (N−A−S−H) gel and calcium silicate hydration (C−S−H) gel, besides the surficial pan-alkali. The research results provide an experimental basis for the reuse of CS in various scenarios.

scholarly journals STUDY ON DRYING SHRINKAGE CRACKING PROPERTIES OF FLY ASH MORTAR UNDER DIFFERENT DRYING CONDITIONS

2017 ◽  
Vol 71 (1) ◽  
pp. 386-393
Author(s):  
Satoshi YOSHIKAWA ◽  
Yoshiaki SATO ◽  
Toshihiro OTANI ◽  
Kenji UEDA
Keyword(s):  
Fly Ash ◽  
Drying Shrinkage ◽  
Shrinkage Cracking ◽  
Drying Conditions

scholarly journals Strength Determination of High Strength Concrete Blended with Copper Slag and Fly Ash

2021 ◽  
Vol 9 (VII) ◽  
pp. 1198-1203
Author(s):  
Jamshed Alam
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Free Water ◽  
High Strength ◽  
Copper Slag ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Strength Concrete ◽  
Free Water Content

An experimental analysis was conducted to study the effects of using copper slag as a fine aggregate (FA) and the effect of fly ash as partial replacement of cement on the properties high strength concrete. In this analysis total ten concrete mixtures were prepared, out of which five mixes containing different proportions of copper slag ranging from 0% (for the control mix) to 75% were prepared and remaining five mixes containing fly ash as partial replacement of cement ranging from 6% to 30% (all mixes contains 50% copper slag as sand replacements). Concrete matrix were tested for compressive strength, tensile strength and flexural strength tests. Addition of copper slag as sand replacement up to 50% yielded comparable strength with that of the control matrix. However, further additions of copper slag, caused reduction in strength due to an increment of the free water content in the mix. Concrete mix with 75% copper slag replacement gave the lowest compressive strength value of approximately 80 MPa at 28 days curing period, which is almost 4% more than the strength of the control mix. For this concrete containing 50% copper slag, fly ash is introduced in the concrete to achieve the better compressive, split and flexural strengths. It was also observed that, introduction of the fly ash gave better results than concrete containing 50% copper slag. When concrete prepared with 18 % of fly ash, the strength has increased approximately 4%, and strength decreased with further replacements of the cement with fly ash. Hence, it is suggested that 50% of copper slag can be used as replacement of sand and 18% fly ash can be used as replacement of cement in order to obtain high strength concrete.

scholarly journals Study of Light Weight Fibre Reinforced Concrete by Partial Replacement of Coarse Aggregate with Pumice Stone

2021 ◽  
Vol 9 (9) ◽  
pp. 933-940
Author(s):  
Mohammed Sohel Ahmed
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Light Weight ◽  
Structural Members ◽  
Conventional Concrete ◽  
Shrinkage Cracking ◽  
Pumice Stone ◽  
Average Compressive Strength

Abstract: As the demand for the structural members application in the concrete industry is continuously increasing simultaneously many a times it is required to lower the density of concrete enabling light weight which helps in easy handling of the concrete and its members. In this research an experimental endeavour has been made to equate conventional concrete with light weight by partially substituting the coarse aggregate with the pumice stone aggregate in M30 grade mix design. Simultaneously small fibres of Recron3's Polypropylene have been applied to the concrete as a reinforcing medium to minimize shrinkage cracking and improve tensile properties. The coarse aggregate was substituted by the pumice aggregate in 10, 20, 30, 40, and 50 percent and fibres respectively in 0.5, 1, 1.5, 2 and 2.5 percent. The experiment is focused on strength parameters to determine the most favourable optimum percent with respect to conventional concrete. Keywords: OPC (Ordinary Portland Cement)1, FA (Fine Aggregate)2, CA (Coarse Aggregate) 3, fck (Characteristic Compressive Strength at 28days)4, Sp. Gr (Specific Gravity)5, WC (Water Content)6, W/C (Water Cement Ratio)7, S (Standard Deviation)8, Fck (Target Average Compressive Strength at 28days)9.

Sign in / Sign up

Export Citation Format

Share Document