scholarly journals Portuguese unbound granular materials characterisation using cyclic triaxial tests

2012 ◽  
Vol 165 (2) ◽  
pp. 139-150 ◽  
Author(s):  
Rosa P. Conceição Luzia ◽  
Luís G. de Picado Santos ◽  
José M. Coelho das Neves ◽  
Dinis Correia Gardete
Keyword(s):  
Granular Materials ◽  
Triaxial Tests ◽  
Cyclic Triaxial ◽  
Cyclic Triaxial Tests ◽  
Unbound Granular Materials

Importance of Measuring Local Strains in Cyclic Triaxial Tests on Granular Materials

2009 ◽  
pp. 288-288-15 ◽  
Author(s):  
F Tatsuoka ◽  
S Teachavorasinskun ◽  
J Dong ◽  
Y Kohata ◽  
T Sato
Keyword(s):  
Granular Materials ◽  
Triaxial Tests ◽  
Cyclic Triaxial ◽  
Cyclic Triaxial Tests ◽  
Local Strains

scholarly journals An Evaluation of the Resilient Modulus and Permanent Deformation of Unbound Mixtures of Granular Materials and Rubber Particles from Scrap Tyres to Be Used in Subballast Layers

2016 ◽  
Author(s):  
Carlos Hidalgo Sgnes
Keyword(s):  
Granular Materials ◽  
Resilient Modulus ◽  
Permanent Deformation ◽  
Waste Material ◽  
Triaxial Tests ◽  
Rubber Content ◽  
Cyclic Triaxial ◽  
Cyclic Triaxial Tests ◽  
Vibration Attenuation ◽  
Rubber Particles

Over the last years rubber from scrap tyres has been reused in different civil works such as road embankments and railway platforms due to its resilient properties, low degradation and vibration attenuation. Unfortunately, this issue is still scarce. For instance, in Spain about 175.000 tonnes of scrap tyres were collected in 2014, of which only 0.6% were reused in civil works. Aiming to contribute to the reutilisation of large quantities of this waste material, this paper focuses on the analysis of unbound mixtures of granular materials with different percentages of rubber particles to be used as subballast layers. Mixtures are tested under cyclic triaxial tests so as to obtain their resilient modulus and evaluate their permanent deformations. It is found that as the rubber content increases, the resilient modulus decreases and the permanent deformation increases. Taking into account the usual loads transmitted to the subballast layer, the optimum rubber content that does not compromise the behaviour of the mixture is set in a range between 2.5% and 5% in terms of weight.DOI: http://dx.doi.org/10.4995/CIT2016.2016.4231

Effect of the loading frequency on the sand liquefaction behaviour in cyclic triaxial tests

2021 ◽  
Vol 147 ◽  
pp. 106779
Author(s):  
Zhehao Zhu ◽  
Feng Zhang ◽  
Qingyun Peng ◽  
Jean-Claude Dupla ◽  
Jean Canou ◽  
...  
Keyword(s):  
Triaxial Tests ◽  
Loading Frequency ◽  
Cyclic Triaxial ◽  
Cyclic Triaxial Tests ◽  
Sand Liquefaction

scholarly journals Combined Resonant Column and Cyclic Triaxial Tests for Measuring Undrained Shear Modulus Reduction of Sand With Plastic Fines

2013 ◽  
Vol 36 (4) ◽  
pp. 20120129 ◽  
Author(s):  
Chadi S. El Mohtar ◽  
Vincent P. Drnevich ◽  
Marika Santagata ◽  
Antonio Bobet
Keyword(s):  
Shear Modulus ◽  
Triaxial Tests ◽  
Resonant Column ◽  
Cyclic Triaxial ◽  
Cyclic Triaxial Tests ◽  
Modulus Reduction ◽  
Undrained Shear

scholarly journals Soil liquefaction as an identification test

2019 ◽  
Vol 92 ◽  
pp. 08008
Author(s):  
Bozana Bacic ◽  
Ivo Herle
Keyword(s):  
Pore Water ◽  
Laboratory Testing ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Initial Density ◽  
Soil Liquefaction ◽  
Triaxial Tests ◽  
Cyclic Triaxial ◽  
Cyclic Triaxial Tests ◽  
Identification Test

Time-consuming and complicated investigations of soil liquefaction in cyclic triaxial tests are the most common way of laboratory analysis of this phenomenon. Moreover, the necessary equipment for the performance of cyclic triaxial tests is very expensive. Much simpler method for laboratory testing of the soil liquefaction has been developed at the Institute of Geotechnical Engineering at the TU Dresden. This method takes into account the pore water pressure build-up during cyclic shearing within a short time period. During the test, the soil sample is subjected to horizontal cyclic loading and the generated pore water pressure is measured. In the first series of these experiments, a dependence of the pore water pressure buildup on the initial density of soil could be observed, as expected. When comparing different soils, it is shown that the tendency to liquefaction depends also on the granulometric properties (e.g. grain size distribution) of the soil. The aim of the further development is to establish a simple identification test for laboratory testing of the soil liquefaction.

Sign in / Sign up

Export Citation Format

Share Document