Determination of the Relationship between the Factor of Grain Size Factor and the Corrosion Rate of Structural Steel

2020 ◽  
Vol 22 (3) ◽  
pp. 106-125
Author(s):  
Roman Sokolov ◽  
◽  
Vitaly Novikov ◽  
Kamil Muratov ◽  
Anatolii Venediktov ◽  
...  
Author(s):  
V.F. Novikov ◽  
R.A. Sokolov ◽  
K.R. Muratov ◽  
A.N. Venediktov

2015 ◽  
Vol 16 (1) ◽  
Author(s):  
Frank Feyerabend ◽  
Martin Johannisson ◽  
Zhidan Liu ◽  
Regine Willumeit-Römer

AbstractSterilization is a necessary step for all implant materials. Different methods can influence the materials properties. Especially important for magnesium as degradable materials is the determination of the corrosion properties. In this study the influence of 70% ethanol, glutaraldehyde, autoclaving, dry heat, UV-, gamma- and electron beam-irradiation on mechanical and corrosion parameters were analyzed. As mechanical parameters hardness and grain size were determined. The corrosion rate under physiological conditions, weight of the corrosion layer and corrosion morphology was determined. It could be demonstrated that irradiation treatments and 70% ethanol are suitable methods, as they decrease the corrosion rate. Heat-introducing methods (autoclaving and dry heat) acted as incomplete ageing treatments on this alloy and therefore increased the corrosion rate. Furthermore, osmolality showed a better correlation to the actual corrosion rate than the pH. Therefore an optimum ratio between alloying system, implant and sterilization method has to be established, depending on the intended application.


2015 ◽  
Vol 8 (1) ◽  
pp. 70-77 ◽  
Author(s):  
Zs. H. Horváth ◽  
A. Véha

Abstract Nowadays, wheat has spread all over the world due to its extensive usability. The colour of wheat grits is very important for the milling and baking industry because it determines the colour of the products made from it. The instrumental colour measuring is used, first of all, for durum wheat. We investigated the relationship between colour characteristics and grain size in the case of different hard aestivum wheats. We determined the colour using the CIE (Commission Internationale de l’Eclairage) 1976 L*, a*, b* colour system measured by MINOLTA CR-300 tristimulus colorimeter. After screening the colour of the wheat fractions of different grain size, grits was measured wet and dry. We determined the L*, a*, b* colour co-ordinates and the whiteness index, too. To evaluate the values we had obtained, we used analysis of variance and regression analysis. We pointed out that the colour of wheat grits of different grain size is dependent on the hardness index of wheat. The lightness co-ordinate (L*) of grits of the harder wheat is smaller, while a* and b* co-ordinates are higher. We also found that while grain size rises, the L* co-ordinate decreases and a*, b* values increase in the case of every type of wheat. The colour of grits is determined by the colour of fractions of 250-400 μm in size, independently from the average grain size. The whiteness index and the L* colour co-ordinate have a linear relation (R2 = 0.9151); so, the determination of whiteness index is not necessary. The L* value right characterizes the whiteness of grits.


2010 ◽  
Vol 63 (12) ◽  
pp. 1201-1204 ◽  
Author(s):  
K.D. Ralston ◽  
N. Birbilis ◽  
C.H.J. Davies

1994 ◽  
Vol 72 (03) ◽  
pp. 426-429 ◽  
Author(s):  
S Kitchen ◽  
I D Walker ◽  
T A L Woods ◽  
F E Preston

SummaryWhen the International Normalised Ratio (INR) is used for control of oral anticoagulant therapy the same result should be obtained irrespective of the laboratory reagent used. However, in the UK National External Quality Assessment Scheme (NEQAS) for Blood Coagulation INRs determined using different reagents have been significantly different.For 18 NEQAS samples Manchester Reagent (MR) was associated with significantly lower INRs than those obtained using Diagen Activated (DA, p = 0.0004) or Instrumentation Laboratory PT-Fib HS (IL, p = 0.0001). Mean INRs for this group were 3.15, 3.61, and 3.65 for MR, DA, and IL respectively. For 61 fresh samples from warfarin-ised patients with INRs of greater than 3.0 the relationship between thromboplastins in respect of INR was similar to that observed for NEQAS data. Thus INRs obtained with MR were significantly lower than with DA or IL (p <0.0001). Mean INRs for this group were 4.01, 4.40, and 4.59 for MR, DA, and IL respectively.We conclude that the differences between INRs measured with the thromboplastins studied here are sufficiently great to influence patient management through warfarin dosage schedules, particularly in the upper therapeutic range of INR. There is clearly a need to address the issues responsible for the observed discrepancies.


2016 ◽  
pp. 137-142
Author(s):  
V.O. Benyuk ◽  
◽  
V.M. Goncharenko ◽  
T.R. Nykoniuk ◽  
◽  
...  

The objective: to еxplore the relationship between the activity of endometrial proliferation and the state of the local immune response in the uterus in the conditions berprestasi process. Patients and methods. Examined 228 women of reproductive and perimenopausal age with endometrial pathology using ultrasound and then performing hysteroresectoscopy. Determination of the concentrations of the cytokines IL-1, IL-2, IL-6 and TNF was performed by solid phase ELISA. Results. Found a trend that confirms the loss of sensitivity to hormones at the stage of malignancy of the endometrium and can be used as diagnostic determinants in determining the nature of intrauterine pathology and criterion of the effectiveness of conservative therapy. Conclusion. Improving etiopatogenetice approach to the therapy of hyperplastic proce.sses of endometrium with determination of receptor phenotype of the endometrium is a research direction in modern gynecology, which will help to improve the results of treatment and prevention of intrauterine pathology. Key words: endometrial hyperplasia,the receptors for progesterone and estrogen, immunohistochemical method.


2012 ◽  
Vol 34 (3) ◽  
pp. 169-184 ◽  
Author(s):  
Hoang Thi Bich Ngoc

Vertical axis wind turbine technology has been applied last years, very long after horizontal axis wind turbine technology. Aerodynamic problems of vertical axis wind machines are discussible. An important problem is the determination of the incidence law in the interaction between wind and rotor blades. The focus of the work is to establish equations of the incidence depending on the blade azimuth, and to solve them. From these results, aerodynamic torques and power can be calculated. The incidence angle is a parameter of velocity triangle, and both the factors depend not only on the blade azimuth but also on the ratio of rotational speed and horizontal speed. The built computational program allows theoretically selecting the relationship of geometric parameters of wind turbine in accordance with requirements on power, wind speed and installation conditions.


1986 ◽  
Vol 14 (4) ◽  
pp. 201-218 ◽  
Author(s):  
A. G. Veith

Abstract This four-part series of papers addresses the problem of systematic determination of the influence of several tire factors on tire treadwear. Both the main effect of each factor and some of their interactive effects are included. The program was also structured to evaluate the influence of some external-to-tire conditions on the relationship of tire factors to treadwear. Part I describes the experimental design used to evaluate the effects on treadwear of generic tire type, aspect ratio, tread pattern (groove or void level), type of pattern (straight rib or block), and tread compound. Construction procedures and precautions used to obtain a valid and functional test method are included. Two guiding principles to be used in the data analyses of Parts II and III are discussed. These are the fractional groove and void concept, to characterize tread pattern geometry, and a demonstration of the equivalence of wear rate for identical compounds on whole tread or multi-section tread tires.


2017 ◽  
Vol 3 (1) ◽  
pp. 42
Author(s):  
Roshanira Che Mohd Noor ◽  
Nur Atiqah Rochin Demong

Providing a safe and healthy workplace is one of the most effective strategies in for holding down the cost of doing construction business. It was a part of the overall management system to facilitate themanagement of the occupational health and safety risk that are associated with the business of the organization. Factors affected the awareness level inclusive of safety and health conditions, dangerous working area, long wait care and services and lack of emergency communication werethe contributed factors to the awareness level for the operational level. Total of 122 incidents happened at Telekom Malaysia Berhad as compared to year 2015 only 86 cases. Thus, the main objective of this study was to determine the relationship between safety and health factors and the awareness level among operational workers.The determination of this research was to increase the awareness level among the operational level workerswho committing to safety and health environment.


Sign in / Sign up

Export Citation Format

Share Document