New methods of electricity generation using steam from waste heat boilers fired by waste gases from high-temperature plants in ferrous metallurgy

2021 ◽  
pp. 68-73
Author(s):  
V. S. Dubinin ◽  
T. A. Stepanova ◽  
S. O. Shkarupa ◽  
V. P. Krupskiy
Keyword(s):  
High Temperature ◽  
Ferrous Metallurgy ◽  
Electricity Generation ◽  
Waste Heat ◽  
New Methods

scholarly journals System Design of Electricity Generation Using Waste Heat from LNG Automobile

2020 ◽  
Vol 145 ◽  
pp. 02062
Author(s):  
Canzong Zhou ◽  
Shuyi Chen ◽  
Wei Cui ◽  
Zhengmao Yao
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Electricity Generation ◽  
Waste Heat ◽  
Cooling System ◽  
Combustion Engine ◽  
Lead Telluride ◽  
Maximum Output ◽  
Thermoelectric Conversion ◽  
Temperature Environment

According to the research, thermoelectricity generation can recycle the heat contained in the cooling system of internal combustion engine. This paper is about taking advantage of the feature in the huge temperature difference at about 560 °C which is formed between high-temperature engine and LNG (Liquefied Natural Gas) in low temperature and the ability that LNG provides semiconductor with thermoelectric conversion material so as to produce the maximum output voltage in low temperature. We take advantage of lead telluride materials that adapt to the high temperature environment and bismuth telluride materials that adapt to the low temperature environment, both of which forms a circuit and are designed as a thermoelectric power generation device. Also, we confirm the possibility of applying the device to cars.

scholarly journals Thermodynamic modelling and efficiency analysis of a class of real indirectly fired gas turbine cycles

2009 ◽  
Vol 13 (4) ◽  
pp. 41-48
Author(s):  
Zheshu Ma ◽  
Zhenhuan Zhu
Keyword(s):  
High Temperature ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Waste Heat ◽  
Operational Parameters ◽  
Forecast Performance ◽  
Micro Gas Turbine ◽  
Temperature Heat

Indirectly or externally-fired gas-turbines (IFGT or EFGT) are novel technology under development for small and medium scale combined power and heat supplies in combination with micro gas turbine technologies mainly for the utilization of the waste heat from the turbine in a recuperative process and the possibility of burning biomass or 'dirty' fuel by employing a high temperature heat exchanger to avoid the combustion gases passing through the turbine. In this paper, by assuming that all fluid friction losses in the compressor and turbine are quantified by a corresponding isentropic efficiency and all global irreversibilities in the high temperature heat exchanger are taken into account by an effective efficiency, a one dimensional model including power output and cycle efficiency formulation is derived for a class of real IFGT cycles. To illustrate and analyze the effect of operational parameters on IFGT efficiency, detailed numerical analysis and figures are produced. The results summarized by figures show that IFGT cycles are most efficient under low compression ratio ranges (3.0-6.0) and fit for low power output circumstances integrating with micro gas turbine technology. The model derived can be used to analyze and forecast performance of real IFGT configurations.

scholarly journals The Role of the Recuperator in High Performance Gas Turbine Applications

1978 ◽  
Author(s):  
C. F. McDonald
Keyword(s):  
High Temperature ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Waste Heat ◽  
Closed Cycle ◽  
Exhaust Waste Heat ◽  
Prime Movers

With soaring fuel costs and diminishing clean fuel availability, the efficiency of the industrial gas turbine must be improved by utilizing the exhaust waste heat by either incorporating a recuperator or by co-generation, or both. In the future, gas turbines for power generation should be capable of operation on fuels hitherto not exploited in this prime-mover, i.e., coal and nuclear fuel. The recuperative gas turbine can be used for open-cycle, indirect cycle, and closed-cycle applications, the latter now receiving renewed attention because of its adaptability to both fossil (coal) and nuclear (high temperature gas-cooled reactor) heat sources. All of these prime-movers require a viable high temperature heat exchanger for high plant efficiency. In this paper, emphasis is placed on the increasingly important role of the recuperator and the complete spectrum of recuperative gas turbine applications is surveyed, from lightweight propulsion engines, through vehicular and industrial prime-movers, to the large utility size nuclear closed-cycle gas turbine. For each application, the appropriate design criteria, types of recuperator construction (plate-fin or tubular etc.), and heat exchanger material (metal or ceramic) are briefly discussed.

EAF Gas Waste Heat Utilization and Discussion of the Energy Conservation and CO2 Emissions Reduction

2016 ◽  
Vol 35 (2) ◽  
pp. 195-200 ◽  
Author(s):  
Ling-zhi Yang ◽  
Rong Zhu ◽  
Guo-hong Ma
Keyword(s):  
High Temperature ◽  
Energy Saving ◽  
Waste Heat ◽  
Hot Metal ◽  
Coal Gas ◽  
Heat Utilization ◽  
High Temperature Furnace ◽  
Metal Ratio ◽  
Waste Heat Utilization ◽  
Temperature Furnace

AbstractAs a large number of energy was taken away by the high temperature furnace gas during the EAF smelting process, a huge economic and environmental benefits would obtained to recycle and utilize. In this paper, the energy of the EAF was analyzed theoretically with the hot metal ratio of 50%. Combined with the utilization of the gas waste heat during the scrap preheating, electricity generation, production of steam and production of coal gas processes, the effect of the energy saving and emission was calculated with comprehensive utilization of the high temperature furnace gas. An optimal scheme for utilization of the waste heat was proposed based on the calculation. The results show that the best way for energy saving and carbon reduction is the production of coal gas, while the optimal scheme for waste heat utilization is combined the production of coal gas with the scrap preheating, which will save 170 kWh/t of energy and decrease 57.88 kg/t of carbon emission. As hot metal ratio in EAF steelmaking is often more than 50%, which will produce more EAF gas waste heat, optimizing EAF gas waste heat utilization will have more obvious effect on energy saving and emission reduction.

Present Situation and Prospect of EAF Gas Waste Heat Utilization Technology

2018 ◽  
Vol 37 (4) ◽  
pp. 357-363 ◽  
Author(s):  
Ling-zhi Yang ◽  
Tao Jiang ◽  
Guang-hui Li ◽  
Yu-feng Guo ◽  
Feng Chen
Keyword(s):  
High Temperature ◽  
Latent Heat ◽  
Waste Heat ◽  
Gas Production ◽  
Raw Material ◽  
Sensible Heat ◽  
Steelmaking Process ◽  
Coal Gas ◽  
Heat Utilization ◽  
Waste Heat Utilization

AbstractWith the increase of hot metal ratio in electric arc furnace (EAF) steelmaking process, physical sensible heat and chemical latent heat of gas increased significantly. As EAF raw material condition is similar to basic oxygen furnace (BOF), and the condition of BOF gas waste heat utilization technology is mature, waste heat utilization technology in EAF steelmaking will be getting more and more attention. Scrap preheating and steam production as mature technology is the main way of EAF gas waste heat utilization. Power generation converted high temperature steam to electricity will further improve the EAF gas utilization value. The previous ways are to recycle physical sensible heat of EAF gas. To use chemical latent heat of gas, the secondary combustion technology is usually adopted to make CO fully burn into CO2. Coal gas production can fully recycle the chemical latent heat of gas theoretically, which is higher efficiency than other ways. Coal gas production needs a stable steelmaking process to stabilize high temperature gas. And the way need to develop EAF sealing technology, oxygen removal technology and gas purification technology, to make gas content meet the requirements of coal gas production in EAF steelmaking process.

Synthesis and Characterization of Aerogel-derived Cation-substituted Hexaaluminates

1996 ◽  
Vol 457 ◽  
Author(s):  
Lin-chiuan Yan ◽  
Levi T. Thompson
Keyword(s):  
High Temperature ◽  
Low Temperature ◽  
Catalytic Combustion ◽  
High Surface ◽  
High Surface Area ◽  
Synthesis And Characterization ◽  
New Methods ◽  
Surface Areas ◽  
Different Characteristics

ABSTRACTNew methods have been developed for the synthesis of high surface area cation-substituted hexaaluminates. These materials were prepared by calcining high temperature (ethanol extraction) or low temperature (CO2 extraction) aerogels at temperatures up to 1600°C. Cation-substituted hexaaluminates have emerged as promising catalysts for use in high temperature catalytic combustion. In comparing unsubstituted and cation-substituted hexaaluminates, we found that the phase transformations were much cleaner for the cation-substituted materials. BaCO3 and BaAl2O4 were intermediates during transformation of the unsubstituted materials, while the cation-substituted materials transformed directly from an amorphous phase to crystalline hexaaluminate. Moreover, the presence of substitution cations caused the transformation to occur at lower temperatures. Mn seems to be a better substitution cation than Co since the Mn-substituted materials exhibited higher surface areas and better heat resistances than the Co-substituted materials. The low temperature aerogel-derived materials possessed quite different characteristics from the high temperature aerogel-derived materials. For example, phase transformation pathways were different.

Sign in / Sign up

Export Citation Format

Share Document