RMS response of a one-dimensional half-space to SH

1996 ◽  
Vol 86 (2) ◽  
pp. 363-370 ◽  
Author(s):  
Steven M. Day

Abstract We examine the extent to which the response of a perfectly elastic half-space to an SH-wave incident from below can be characterized when knowledge about the elastic structure is limited to the near surface. Elastic properties are modeled as piecewise continuous functions of the depth coordinate. It is found that the site amplification function can be determined with a frequency resolution that depends inversely on the depth to which the elastic structure is known. Specifically, certain spectral averages of the site amplification function, concentrated over bandwidth Δƒ, depend only on the elastic structure down to a two-way travel-time depth of 1/Δƒ. These spectral averages are entirely independent of the elastic properties at greater depth. Equivalently, when the incident motion has a bandlimited white power spectrum of bandwidth Δƒ, the site amplification of the root mean square (rms) ground motion depends only on the elastic structure down to a two-way travel-time depth of 1/Δƒ. When the bandwidth is sufficiently large, the following corollary applies: the rms surface ground motion equals the rms incident motion multiplied by 2√Ib/I0, where I0 and Ib are shear impedances at the ground surface and basement depth, respectively. This result provides justification for a procedure conventionally used to correct stochastic estimates of earthquake ground motion to account for local site effects. The analysis also clarifies the limitations of that conventional procedure. The results define specific site-response parameters that can be computed from knowledge of shallow structure alone and may thereby contribute to improved understanding of the physical basis for, and limitations of, site classification schemes that are based on average S-wave velocity at shallow depth. While the analytical results are rigorous only for infinite Q, numerical experiments indicate that similar results apply to models with finite, frequency-independent Q. The practical utility of the results is likely to be limited primarily by the degree of lateral heterogeneity present near sites of interest and the degree to which the sites respond nonlinearly to incident ground motion.

2020 ◽  
Vol 110 (6) ◽  
pp. 2862-2881
Author(s):  
Arthur J. Rodgers ◽  
Arben Pitarka ◽  
Ramesh Pankajakshan ◽  
Bjorn Sjögreen ◽  
N. Anders Petersson

ABSTRACT Large earthquake ground-motion simulations in 3D Earth models provide constraints on site-specific shaking intensities but have suffered from limited frequency resolution and ignored site response in soft soils. We report new regional-scale 3D simulations for moment magnitude 7.0 scenario earthquakes on the Hayward Fault, northern California with SW4. Simulations resolved significantly broader band frequencies (0–10 Hz) than previous studies and represent the highest resolution simulations for any such earthquake to date. Seismic waves were excited by a kinematic rupture following Graves and Pitarka (2016) and obeyed wave propagation in a 3D Earth model with topography from the U.S. Geological Survey (USGS) assuming a minimum shear wavespeed, VSmin, of 500  m/s. We corrected motions for linear and nonlinear site response for the shear wavespeed, VS, from the USGS 3D model, using a recently developed ground-motion model (GMM) for Fourier amplitude spectra (Bayless and Abrahamson, 2018, 2019a). At soft soil locations subjected to strong shaking, the site-corrected intensities reflect the competing effects of linear amplification by low VS material, reduction of stiffness during nonlinear deformation, and damping of high frequencies. Sites with near-surface VS of 500  m/s or greater require no linear site correction but can experience amplitude reduction due to nonlinear response. Averaged over all sites, we obtained reasonable agreement with empirical ergodic median GMMs currently used for seismic hazard and design ground motions (epsilon less than 1), with marked improvement at soft sedimentary sites. At specific locations, the simulated shaking intensities show systematic differences from the GMMs that reveal path and site effects not captured in these ergodic models. Results suggest how next generation regional-scale earthquake simulations can provide higher spatial and frequency resolution while including effects of soft soils that are commonly ignored in scenario earthquake ground-motion simulations.


Author(s):  
Athanasius Cipta ◽  
Phil Cummins ◽  
Masyhur Irsyam ◽  
Sri Hidayati

We use earthquake ground motion modelling via Ground Motion Prediction Equations (GMPEs) and numerical simulation of seismic waves to consider the effects of site amplification and basin resonance in Jakarta, the capital city of Indonesia. While spectral accelerations at short periods are sensitive to near-surface conditions (i.e., Vs30), our results suggest that, for basins as deep as Jakarta’s, available GMPEs cannot be relied upon to accurately estimate the effect of basin depth on ground motions at long periods (>1 s). Amplitudes at such long periods are influenced by entrapment of seismic waves in the basin, resulting in longer duration of strong ground motion, and interference between incoming and reflected waves as well as focusing at basin edges may amplify seismic waves. In order to simulate such phenomena in detail, a basin model derived from a previous study is used as a computational domain for deterministic earthquake scenario modeling in a 2-dimensional cross-section. A Mw 9.0 megathrust, a Mw 6.5 crustal thrust and a Mw 7.0 instraslab earthquake are chosen as scenario events that pose credible threats to Jakarta, and the interactions with the basin of seismic waves generated by these events were simulated. The highest PGV amplifications are recorded at sites near the middle of the basin and near its southern edge, with maximum amplifications of PGV in the horizontal component of 200% for the crustal, 600% for the megathrust and 335% for the deep intraslab earthquake scenario, respectively. We find that the levels of ground motion response spectral acceleration fall below those of the 2012 Indonesian building Codes's design response spectrum for short periods (< 1 s), but closely approach or may even exceed these levels for longer periods.


2011 ◽  
Vol 42 (1) ◽  
pp. 69-79 ◽  
Author(s):  
Hiroaki Yamanaka ◽  
Kaoru Ohtawara ◽  
Rhommel Grutas ◽  
Robert B. Tiglao ◽  
Melchor Lasala ◽  
...  

2018 ◽  
Vol 55 (7) ◽  
pp. 928-940
Author(s):  
Jeremy M. Gosselin ◽  
John F. Cassidy ◽  
Stan E. Dosso ◽  
Camille Brillon

This paper applies rigorous quantitative inversion methods to estimate seismic-hazard site classification and amplification factors in Kitimat, British Columbia, due to near-surface geophysical conditions. Frequency-wavenumber seismic-array processing is applied to passive data collected at three sites in Kitimat to estimate surface-wave dispersion. The dispersion data are inverted using a fully nonlinear Bayesian (probabilistic) inference methodology to estimate shear-wave velocity (VS) profiles and uncertainties. The VS results are used to calculate the travel-time average of VS to 30 m depth (VS30) as a representation of the average sediment conditions, and to determine seismic-hazard site classification with respect to the National Building Code of Canada. In addition, VS30-dependent site amplification factors are computed to estimate site amplification at the three Kitimat sites. Lastly, the VS profiles are used to compute amplification and resonance spectra for horizontally polarized shear waves. Quantitative uncertainties are estimated for all seismic-hazard estimates from the probabilistic VS structure. The Kitimat region is the site for several proposed large-scale industrial development projects. One of the sites considered in this study is co-located with a recently deployed soil seismographic monitoring station that is currently recording ground motions as part of a 5 year campaign. The findings from this work will be useful for mitigating seismic amplification and resonance hazards on critical infrastructure, as well as for future seismological research, in this environmentally and economically significant region of Canada.


2015 ◽  
Author(s):  
Hiroaki Yamanaka ◽  
Kosuke Chimoto ◽  
Seiji Tsuno ◽  
Koichiro Saguchi ◽  
Hitoshi Morikawa ◽  
...  

2021 ◽  
Vol 11 (5) ◽  
pp. 7658-7664
Author(s):  
T. Nagao

The considered parameters in seismic design vary, with the Earthquake Ground Motion (EGM) having the largest variation. Since source characteristic, path characteristic, and Site Amplification Factor (SAF) influence the EGM, it is crucial to appropriately consider their variations. Source characteristic variations are mainly considered in a seismic hazard analysis, which is commonly used to evaluate variations in EGM. However, it is also important to evaluate variations in path characteristic and SAF with only a few studies having individually and quantitatively examined the variations of these two characteristics. In this study, based on strong-motion observation records obtained from four sites in central Japan, the three characteristics were extracted from seismograms using the concept of spectral inversion. After removing the source characteristic, the path characteristic and SAF were separated, and the variations in these two characteristics were quantified. To separate and obtain each characteristic from the observed record, one constraint condition must be imposed, whereas the variations in the constraint condition must be ignored. In that case, the variations in the constraint condition are included in the variations of the separated characteristics. In this study, this problem was solved by evaluating the variation in the constraint condition, which is the SAF at a hard rock site, by the use of the vertical array observation record at the site.


Sign in / Sign up

Export Citation Format

Share Document