scholarly journals PENGARUH VARIASI CAMPURAN OLI BEKAS DAN BIOSOLAR TERHADAP KARAKTERSITIK UJI PEMBAKARAN DROPLET

2017 ◽  
Vol 2 (2) ◽  
pp. 83-96
Author(s):  
Akhmad Syarief ◽  
Ahmad Ramadan ◽  
Misbachudin Misbachudin
Keyword(s):  
Burning Rate ◽  
Ignition Delay ◽  
Delay Time ◽  
Ignition Delay Time ◽  
Fuel Mixture ◽  
Flash Point ◽  
Test Characteristics ◽  
Used Oil ◽  
Maximum Value ◽  
Mixed Oil

This study aims to determine the effect of mixed used oil and biodiesel mixture on droplet combustion test characteristics. . This research was conducted by dripping the fuel at the tip of the thermocouple to form a droplet with a volume of 0.1 mm, then bringing the heater to the droplet to form a fire. This study aims to determine the influence of mixed oil and biosolar of flash point value, ignition delay time, burning rate and maximum fire height. This research used variation of used oil mixture 10%, 20%, 30%, 40% and 50%. The results show that flash point value increases with increasing percentage of used oil, which is influenced by the viscosity, density, and volatility of each variation of fuel mixture. The value of the ignition delay time increases with increasing percentage of used oil, which is influenced by the viscosity, density and volatility of each variation of fuel mixture. The burning rate value decreases with the increase of the used oil mixture, which is influenced by the viscosity, density, and volatility of each variation of fuel mixture. The maximum value of fire that can be achieved decreases, along with the increase of variation of used oil mixture and is influenced by viscosity, density and volatility value and each variation of fuel mixture.

scholarly journals UJI KARAKTERISTIK PEMBAKARAN HASIL DESTILASI KARET BEKAS-MINYAK DIESEL DENGAN MENGGUNAKAN DROPLET

JTAM ROTARY ◽  
2020 ◽  
Vol 1 (1) ◽  
pp. 1
Author(s):  
Aji Indra Hartono ◽  
Aqli Mursadin
Keyword(s):  
Burning Rate ◽  
Ignition Delay ◽  
Delay Time ◽  
Ignition Delay Time ◽  
Diesel Oil ◽  
Combustion Characteristics ◽  
Flash Point ◽  
Rubber Compound ◽  
Oil Droplet

This study aims to look at the combustion characteristics of destillates of used rubber and diesel oil using droplet, the characteristics observed were flash point, ignition delay time, burning rate, and visualization (hight) of fire. Variation in mix RCO 10%, 20%, 30%, 40%, 50%. The tool used is a tool designed by researchers. The result of the flash point study found that the highest velue was found in the mixture of RCO 10% which was 105,7oC and the lowest value was found in mixture of 50% which was 56,6oC. then the highest value of the ignition delay time is in the mixture of 10% which is 1,64 seconds and the lowest value in the mixture is 30% which is 0,98 seconds, then are result of the highest burning rate are found in the mixture 0f 40% which is 3,83 seconds and lowest value is mixed with 20% which is 3,1 second. Then the highest level of fire in the mixture of 10% is 82,3 mm and the lowest is in the mixture of 50% which is 73,2 mm. Keywords: Rubber Compound Oil, Droplet, Flash Point, Ignition Delay Time, Burning Rate

Numerical Study on the Effect of Real Syngas Compositions on Ignition Delay Times and Laminar Flame Speeds at Gas Turbine Conditions

2013 ◽  
Author(s):  
Olivier Mathieu ◽  
Eric L. Petersen ◽  
Alexander Heufer ◽  
Nicola Donohoe ◽  
Wayne Metcalfe ◽  
...  
Keyword(s):  
Ignition Delay ◽  
Delay Time ◽  
Gas Turbines ◽  
Ignition Delay Time ◽  
Laminar Flame ◽  
Numerical Study ◽  
Fuel Mixture ◽  
Flame Speed ◽  
Operating Conditions ◽  
Combustion Properties

Depending on the feedstock and the production method, the composition of syngas can include (in addition to H2 and CO) small hydrocarbons, diluents (CO2, water, and N2), and impurities (H2S, NH3, NOx, etc.). Despite this fact, most of the studies on syngas combustion do not include hydrocarbons or impurities and in some cases not even diluents in the fuel mixture composition. Hence, studies with realistic syngas composition are necessary to help designing gas turbines. The aim of this work was to investigate numerically the effect of the variation in the syngas composition on some fundamental combustion properties of premixed systems such as laminar flame speed and ignition delay time at realistic engine operating conditions. Several pressures, temperatures, and equivalence ratios were investigated. To perform this parametric study, a state-of-the-art C0-C5 detailed kinetics mechanism was used. Results of this study showed that the addition of hydrocarbons generally reduces the reactivity of the mixture (longer ignition delay time, slower flame speed) due to chemical kinetic effects. The amplitude of this effect is however dependent on the nature and concentration of the hydrocarbon as well as the initial condition (pressure, temperature, and equivalence ratio).

scholarly journals Ignition and combustion of high-energy materials containing aluminum, boron and aluminum diboride

2018 ◽  
Vol 194 ◽  
pp. 01055
Author(s):  
Alexander Korotkikh ◽  
Ivan Sorokin ◽  
Ekaterina Selikhova
Keyword(s):  
Burning Rate ◽  
Ignition Delay ◽  
Delay Time ◽  
Solid Propellant ◽  
Ignition Delay Time ◽  
High Energy ◽  
Solid Propellants ◽  
Amorphous Boron ◽  
Aluminum Diboride ◽  
Ignition And Combustion

Boron and its compounds are among the most promising metal fuel components to be used in solid propellants for solid fuel rocket engine and ramjet engine. Papers studying boron oxidation mostly focus on two areas: oxidation of single particles and powders of boron, as well as boron-containing composite solid propellants. This paper presents the results of an experimental study of the ignition and combustion of the high-energy material samples based on ammonium perchlorate, ammonium nitrate, and an energetic combustible binder. Powders of aluminum, amorphous boron and aluminum diboride, obtained by the SHS method, were used as the metallic fuels. It was found that the use of aluminum diboride in the solid propellant composition makes it possible to reduce the ignition delay time by 1.7–2.2 times and significantly increase the burning rate of the sample (by 4.8 times) as compared to the solid propellant containing aluminum powder. The use of amorphous boron in the solid propellant composition leads to a decrease in the ignition delay time of the sample by a factor of 2.2–2.8 due to high chemical activity and a difference in the oxidation mechanism of boron particles. The burning rate of this sample does not increase significantly.

scholarly journals Influence of high ethane content on natural gas ignition

2019 ◽  
Vol 16 (1) ◽  
pp. 36-42
Author(s):  
Hernando Alexander Yepes-Tumay ◽  
Arley Cardona-Vargas
Keyword(s):  
Natural Gas ◽  
Ignition Delay ◽  
Delay Time ◽  
Ignition Delay Time ◽  
Fuel Mixture ◽  
Ignition Limit ◽  
Mode Analysis ◽  
Gas Combustion ◽  
Gas Ignition ◽  
Natural Gas Combustion

The effect of ethane on combustion and natural gas autoignition was studied in the present paper. Two fuel mixture of natural gas with high ethane content were considered, 75% CH4 – 25% C2H6 (mixture 1), and 50% CH4 – 50% C2H6 (mixture 2). Natural gas combustion incidence was analyzed through the calculation of energy properties and the ignition delay time numerical calculations along with an ignition mode analysis. Specifically, the strong ignition limit was calculated to determine the effect of ethane on natural gas autoignition. According to the results, ignition delay time decreases for both mixtures in comparison with pure methane. The strong ignition limit shifts to lower temperatures when ethane is present in natural gas chemical composition.  

scholarly journals Single Droplet Combustion Characteristics of Petroleum Diesel- Philippine Tung Biodiesel Blends

2021 ◽  
Vol 18 (24) ◽  
pp. 1409
Author(s):  
Nurkholis Hamidi ◽  
Joko Nugroho
Keyword(s):  
Burning Rate ◽  
Ignition Delay ◽  
Delay Time ◽  
Ignition Delay Time ◽  
Ambient Pressure ◽  
Flame Temperature ◽  
Combustion Characteristics ◽  
Chamber Pressure ◽  
Droplet Combustion ◽  
Fuel Blends

The purpose of the present study is to investigate the effects of fuel blending of petroleum diesel and biodiesel made from Philippine Tung on the combustion characteristics of fuel droplets. In this study, petroleum diesel was mixed with biodiesel at volume percentages of 0 to 100 % to produce 5 fuel blends. The ratios of fuel blends (petroleum volume/biodiesel volume) were 100:0 (P100), 75:25 (BP25), 50:50 (BP50), 25:75 (BP75) and 0:100 (B100). Single droplet combustion experiments were prepared to understand the combustion characteristics at 3 levels of ambient pressure (100, 200 and 300 kPa). Observations were carried out on the ignition delay time, the burning rate constant, droplet temperature, and the flame visualization. The results showed some effects of the adding of biodiesel in petroleum diesel and the chamber pressure on droplet combustion characteristics.  The adding of biodiesel into petroleum diesel resulted in a shorter ignition delay time and higher burning rate constants. But, the lower heating value of biodiesel caused the lower flame temperature. The possibility of micro-explosion also increased due to the mixing of fuel. On the other hand, increasing the chamber pressure also resulted in shorter ignition delay, higher burning rate, and higher combustion temperature. The higher ambient pressure also compressed the flame dimension and enhanced the onset of micro-explosion. HIGHLIGHTS The adding of biodiesel into petroleum diesel with different physical and chemical properties impacts the droplet combustion behavior, especially on the characteristics of burning rate, ignition delay time, flame temperature, and micro explosion The high content of unsaturated fatty acids and oxygen in Philippine Tung biodiesel improves the ignition delay time and burning rate constants of the blended fuel, but, the lower heating value causes the lower flame temperature The multi-components of fatty acids with different boiling points in Philippine Tung oil promote the micro-explosion in the combustion of the mixtures of biodiesel and petroleum diesel fuel GRAPHICAL ABSTRACT

3D simulation study on the influence of lubricant oil droplets on pre-ignition in turbocharged DISI engines

2017 ◽  
Vol 232 (12) ◽  
pp. 1677-1693 ◽  
Author(s):  
Yongcheng Huang ◽  
Yaoting Li ◽  
Wenjia Zhang ◽  
Fansheng Meng ◽  
Zhechen Guo
Keyword(s):  
Simulation Study ◽  
Ignition Delay ◽  
Delay Time ◽  
Ignition Delay Time ◽  
Fuel Mixture ◽  
Oil Droplets ◽  
Oil Droplet ◽  
Lubricant Oil ◽  
Auto Ignition ◽  
Reactive Radicals

A skeletal chemical kinetic model for the simulation of auto-ignition and flame propagation characteristics of primary reference fuel (PRF) was developed. Coupled with this model, 3D simulations were applied to investigate the influence of lubricant oil droplets on pre-ignition in a turbocharged direct-injection spark-ignition (DISI) engine at low-speed high-load operating conditions. First, a simulation study on the influence of a lubricant oil droplet on auto-ignition of gasoline substitute and air mixture was performed in a constant-volume chamber. The results revealed that with an increase of the lubricant oil droplet diameter, the ignition delay time for the air/fuel mixture initially decreased and then increased. The ignition delay time was further shortened with the increase of the temperature of the lubricant oil droplet and the temperature and pressure of the mixture. Moreover, it was found that when n-heptane (n-C7H16) was used as a substitute for the direct evaporation product of the lubricant oil droplet, the shortening of the ignition delay time for the air/fuel mixture caused by lubricant oil evaporation was not enough to initiate pre-ignition. When octyl hydrogen peroxide ketone (C8KET) was chosen as a representative of the accumulated stable reactive radicals, the ignition delay time was significantly shortened and was short enough to trigger pre-ignition. Therefore, pre-ignition may not be induced by the direct evaporation product of an lubricant oil droplet but by the accumulated stable reactive radicals. A simulation study on auto-ignition and flame propagation of the air/fuel mixture with the presence of a lubricant oil droplet was then conducted in a turbocharged DISI engine. The results successfully predicted the auto-ignition of the air/fuel mixture near the lubricant oil droplet before the spark ignition timing. Finally, a more convincing mechanism for pre-ignition induced by lubricant oil droplets is proposed to provide some clues for further investigation.

THERMAL BEHAVIOR AND IGNITION OF HIGH-ENERGY MATERIALS CONTAINING B, ALB2, AND TIB2

2020 ◽  
Author(s):  
A. G. Korotkikh ◽  
◽  
V. A. Arkhipov ◽  
I. V. Sorokin ◽  
E. A. Selikhova ◽  
...  
Keyword(s):  
Heat Flux ◽  
Thermal Behavior ◽  
Flux Density ◽  
Ignition Delay ◽  
Delay Time ◽  
Heat Flux Density ◽  
Ignition Delay Time ◽  
High Energy ◽  
Energy Materials ◽  
High Energy Materials

The paper presents the results of ignition and thermal behavior for samples of high-energy materials (HEM) based on ammonium perchlorate (AP) and ammonium nitrate (AN), active binder and powders of Al, B, AlB2, and TiB2. A CO2 laser with a heat flux density range of 90-200 W/cm2 was used for studies of ignition. The activation energy and characteristics of ignition for the HEM samples were determined. Also, the ignition delay time and the surface temperature of the reaction layer during the heating and ignition for the HEM samples were determined. It was found that the complete replacement of micron-sized aluminum powder by amorphous boron in a HEM sample leads to a considerable decrease in the ignition delay time by a factor of 2.2-2.8 at the same heat flux density due to high chemical activity and the difference in the oxidation mechanisms of boron particles. The use of aluminum diboride in a HEM sample allows one to reduce the ignition delay time of a HEM sample by a factor of 1.7-2.2. The quasi-stationary ignition temperature is the same for the AlB2-based and AlB12-based HEM samples.

Sign in / Sign up

Export Citation Format

Share Document