scholarly journals Effect of the Abrasive Grain Distribution on Ground Surface Roughness

2022 ◽  
Vol 16 (1) ◽  
pp. 38-42
Author(s):  
Nobuhito Yoshihara ◽  
◽  
Haruki Takahashi ◽  
Masahiro Mizuno
Keyword(s):  
Surface Roughness ◽  
Theoretical Analysis ◽  
Grain Shape ◽  
Ground Surface ◽  
Clear Understanding ◽  
Abrasive Grain ◽  
Grinding Conditions ◽  
Grain Distribution ◽  
Ground Surface Roughness ◽  
The Relationship

In order to reduce the grinding surface roughness, it is necessary to optimize the grinding conditions; this requires clear understanding of the relationship between the grinding conditions and ground surface roughness. Therefore, various studies have been carried out over the decades on the ground surface roughness and have proposed statistical grinding theory to define the relationship between the grinding conditions and ground surface roughness. However, the statistical grinding theory does not consider a few grinding conditions such as abrasive grain shape and distribution of abrasive grain, which affect the ground surface roughness. In this study, we construct a statistical grinding theory that considers the effect of abrasive grain distribution and improves the accuracy of the theoretical analysis of the ground surface roughness.

Effect of the Grain Depth of Cut on Cross Sectional Profile - Theoretical Analysis of Ground Surface Roughness

2012 ◽  
Vol 565 ◽  
pp. 28-33
Author(s):  
Nobuhito Yoshihara ◽  
Hiroaki Murakami ◽  
Naohiro Nishikawa ◽  
Masahiro Mizuno ◽  
Toshirou Iyama
Keyword(s):  
Surface Roughness ◽  
Ground Surface ◽  
Depth Of Cut ◽  
Cross Sectional ◽  
Grinding Conditions ◽  
Cross Sectional Profile ◽  
Fundamental Research ◽  
Sectional Profile ◽  
Ground Surface Roughness ◽  
The Relationship

Roughness is important criterion of ground surface. When the surface roughness is demanded to be smooth, it is required to make the grinding conditions optimum. To optimize the grinding conditions, relationship between grinding conditions and ground surface roughness must be known. Therefore, it has been attempted to reveal the effect of grinding conditions on the roughness of ground surface over the years. From previous researches, it becomes possible to estimate the ground surface roughness with statistical grinding theory. However, there are some parameters, such as wheel depth of cut and distribution of abrasive grain, are not factored in the theory. In this paper, fundamental research on cross sectional profile is carried out to consider the relationship between the wheel depth of cut and ground surface roughness.

scholarly journals Evaluation of the Relationship Among Dressing Conditions Using Prismatic Dresser, Dressing Resistance, and Grinding Characteristics

2022 ◽  
Vol 16 (1) ◽  
pp. 12-20
Author(s):  
Gen Uchida ◽  
Takazo Yamada ◽  
Kouichi Ichihara ◽  
Makoto Harada ◽  
Tatsuya Kohara ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Condition ◽  
Ground Surface ◽  
Grinding Wheel ◽  
Grinding Process ◽  
Practical Application ◽  
Wheel Surface ◽  
The Difference ◽  
Ground Surface Roughness ◽  
The Relationship

In the grinding process, the grinding wheel surface condition changes depending on the dressing conditions, which affects the ground surface roughness and grinding resistance. Several studies have been reported on the practical application of dressing using prismatic dressers in recent years. However, only a few studies that quantitatively evaluate the effects of differences in dressing conditions using prismatic dresser on the ground surface roughness and grinding resistance have been reported. Thus, this study aims to evaluate quantitatively the effect of the difference in dressing conditions using the prismatic dresser on the ground surface roughness and grinding resistance by focusing on the dressing resistance. In the experiment, dressing is performed by changing the dressing lead and the depth of dressing cut with a prismatic dresser, and the ground surface roughness and grinding resistance are measured. Consequently, by increasing the dressing lead and the depth of dressing cut, the ground surface roughness increased, and the grinding resistance decreased. This phenomenon was caused by the increase in dressing resistance when the dressing lead and the depth of dressing cut were increased, which caused a change in the grinding wheel surface condition. Furthermore, the influence of the difference in dressing conditions using the prismatic dresser on the ground surface roughness and grinding resistance can be quantitatively evaluated by using the dressing resistance.

Study on Lubricating and Cooling Effects of Several Cooling Systems Used in Face Grinding

2005 ◽  
Vol 291-292 ◽  
pp. 221-226
Author(s):  
Takeshi Tanaka ◽  
T. Kobayashi
Keyword(s):  
Surface Roughness ◽  
Removal Rate ◽  
Ground Surface ◽  
Cooling Effect ◽  
Wet Grinding ◽  
Grinding Conditions ◽  
Cooling Effects ◽  
Stock Removal ◽  
Ground Surface Roughness ◽  
Face Grinding

We observed that the lubrication effect is greater than the cooling effect for decreasing the friction heat in face grinding. It was clarified that cool-air grinding is difficult to apply to face grinding under the present grinding conditions. We could obtain the minimum ground surface roughness (hereafter noted as surface roughness) at a mist suppｌy volume of 15 to 30ml/h in mist grinding. The largest stock removal rate (hereafter noted as grinding efficiency) is obtained in mist grinding. However, grinding efficient was small in cool-air mist grinding, by which a large cooling effect of cool air was expected. Though mist and cool-air mist grinding perform similar to wet grinding in few grinding passes, wet grinding is properly applied by large chip removal action in many grinding passes.

Development of Electroplated CBN Wheel with Cemented Carbide Base for Precision Grinding of Compressor Cylinder Vane Slot

2007 ◽  
Vol 329 ◽  
pp. 495-500
Author(s):  
Hang Gao ◽  
W.G. Liu ◽  
Y.G. Zheng
Keyword(s):  
Surface Roughness ◽  
Ground Surface ◽  
Cemented Carbide ◽  
Grinding Wheel ◽  
Precision Grinding ◽  
Base Surface ◽  
Compressor Cylinder ◽  
Cbn Wheel ◽  
Micro Holes ◽  
Ground Surface Roughness

It is experimentally found that existing micro-holes or micro-concaves on the cemented carbide base surface of electroplated CBN wheel is one of important reasons to worsen the combining intensity of the electroplated abrasives layer with the grinding wheel base. It is well solved by sealing the holes or concaves with steam sealing method. Further more the electroplated CBN wheel with cemented carbide base for precision grinding of compressor cylinder vane slot is developed by optimizing the electroplating prescription and process. Productive grinding results show that the ground surface roughness, size precision and the wheel life have reached the advanced index of the same type of wheel imported.

An Experimental Investigation of Optimal Grinding Condition for Aspheric Surface Lens Using Full Factorial Design

2007 ◽  
Vol 329 ◽  
pp. 27-32 ◽  
Author(s):  
Seung Yub Baek ◽  
Jung Hyung Lee ◽  
Eun Sang Lee ◽  
H.D. Lee
Keyword(s):  
Surface Roughness ◽  
Ground Surface ◽  
Diamond Wheel ◽  
Aspheric Surface ◽  
Precision Grinding ◽  
Spherical Lens ◽  
Ultra Precision ◽  
Ground Surface Roughness ◽  
Grinding System ◽  
Micro Lens

To enhance the precision and productivity of ultra precision aspheric surface micro lens, the development of ultra-precision grinding system and process for the aspheric surface micro lens are described. In this paper, an ultra-precision grinding system for manufacturing the aspheric surface micro lens was developed by considering the factors affecting the grinding surface roughness and profile accuracy. This paper deals with the mirror grinding of an aspheric surface micro lens by resin bonded diamond wheel and with the spherical lens of BK7. The optimization of grinding conditions with respect to ground surface roughness and profiles accuracy is investigated by design of experiments.

Analysis of Effective Cutting-Edge Distribution of Grinding Wheel Based on Topography of Working and Ground Surfaces

2011 ◽  
Vol 325 ◽  
pp. 60-65
Author(s):  
Haruhisa Sakamoto ◽  
Kyoko Nakamura ◽  
Yoshinori Sasaki ◽  
Shinji Shimizu
Keyword(s):  
Surface Topography ◽  
Grain Shape ◽  
Pure Copper ◽  
Surface Profile ◽  
Ground Surface ◽  
Cutting Edge ◽  
Grinding Wheel ◽  
Noise Component ◽  
Working Surface ◽  
Ground Surface Roughness

In this study, the determination method of the number of the effective cutting-edges had been proposed based on the measurements of working surface topography and the grinding force. Furthermore, its validity is made clear based on the topographical analysis of the ground surface roughness of pure copper, which is excellent in transcribing the working surface. From the results, the following are found out: The ground surface topography contains the periodical component, which is originated in the grinding and dressing conditions, on the fractal noise component. The cutting traces by each cutting-edge can be countable from the ground surface profile, and then, the number of the effective cutting-edges is identified at one line within the working surface. On the other hand, the number of the effective cutting-edges also can be identified based on the working surface, but, this method requires the determination of the typical grain shape. From the experiment, it is confirmed that the grain shape should be almost spherical for making the numbers of the effective cutting-edge identified from the working and ground surfaces equal.

Effect of Ground Surface Roughness of Tool on Adhesion Characteristics of PVD Coating

2010 ◽  
Vol 126-128 ◽  
pp. 609-614 ◽  
Author(s):  
Masahiro Furuno ◽  
Koichi Kitajima ◽  
Yousuke Tsukuda ◽  
Takeshi Akamatsu
Keyword(s):  
Surface Roughness ◽  
Smooth Surface ◽  
Ground Surface ◽  
Scratch Testing ◽  
Coating Adhesion ◽  
Pvd Coating ◽  
Ground Surface Roughness

This study investigated adhesion of coatings on a grinding surface. This was carried out using scratch testing as a function of surface roughness. Three types of coatings were explored: TiAlN, CrSiN and TiSiN. With smaller surface roughness, the coating adhesion showed a tendency to become stronger. In particular, in the case of surface roughness under 2 micrometers for a coating, the coating adhesion was good. Specifically, the CrSiN coating yielded a very smooth surface.

Sign in / Sign up

Export Citation Format

Share Document