Effect of Borehole Inclination, Annular Clearance, on the Hole Cleaning Efficiency for Water Based Drilling Muds

2010 ◽  
Author(s):  
Mohamed N. Noui-Mehidi ◽  
Mohamed Amanullah
Keyword(s):  
Cleaning Efficiency ◽  
Hole Cleaning ◽  
Water Based ◽  
Drilling Muds ◽  
Annular Clearance

scholarly journals Comparative Analysis of the Effect of Barite and Hematite on the Rheology of Water-Based Drilling Mud

2021 ◽  
Vol 1 (2) ◽  
Author(s):  
Osei H
Keyword(s):  
Rheological Properties ◽  
Drilling Fluid ◽  
Attrition Rate ◽  
Drilling Mud ◽  
Cleaning Efficiency ◽  
Drilling Operation ◽  
Water Based ◽  
Petroleum Resources ◽  
Drilling Muds ◽  
The Impact

High demand for oil and gas has led to exploration of more petroleum resources even at remote areas. The petroleum resources are found in deeper subsurface formations and drilling into such formations requires a well-designed drilling mud with suitable rheological properties in order to avoid or reduce associated drilling problems. This is because rheological properties of drilling muds have considerable effect on the drilling operation and cleaning of the wellbore. Mud engineers therefore use mud additives to influence the properties and functions of the drilling fluid to obtain the desired drilling mud properties especially rheological properties. This study investigated and compared the impact of barite and hematite as weighting agents for water-based drilling muds and their influence on the rheology. Water-based muds of different concentrations of weighting agents (5%, 10%, 15% and 20% of the total weight of the drilling mud) were prepared and their rheological properties determined at an ambient temperature of 24ᵒC to check their impact on drilling operation. The results found hematite to produce higher mud density, plastic viscosity, gel strength and yield point when compared to barite at the same weighting concentrations. The higher performance of the hematite-based muds might be attributed to it having higher specific gravity, better particle distribution and lower particle attrition rate and more importantly being free from contaminants. The water-based muds with hematite will therefore be more promising drilling muds with higher drilling and hole cleaning efficiency than those having barite.

Improving Hole Cleaning Efficiency using Nanosilica in Water-Based Drilling Mud

2018 ◽  
Author(s):  
Afeez O. Gbadamosi ◽  
Radzuan Junin ◽  
Jeffrey O. Oseh ◽  
Augustine Agi ◽  
Nurudeen Yekeen ◽  
...  
Keyword(s):  
Drilling Mud ◽  
Cleaning Efficiency ◽  
Hole Cleaning ◽  
Water Based

Hole-Cleaning Fibers Improve Cuttings-Carrying Capacity

2021 ◽  
Vol 73 (05) ◽  
pp. 63-64
Author(s):  
Chris Carpenter
Keyword(s):  
Flow Regime ◽  
Carrying Capacity ◽  
Rheological Model ◽  
Drilling Fluid ◽  
Test Method ◽  
Abu Dhabi ◽  
Rheological Parameters ◽  
Cleaning Efficiency ◽  
Hole Cleaning ◽  
Drilling Operations

This article, written by JPT Technology Editor Chris Carpenter, contains highlights of paper SPE 203147, “Investigating Hole-Cleaning Fibers’ Mechanism To Improve Cutting Carrying Capacity and Comparing Their Effectiveness With Common Polymeric Pills,” by Mohammad Saeed Karimi Rad, Mojtaba Kalhor Mohammadi, SPE, and Kourosh Tahmasbi Nowtarki, International Drilling Fluids, prepared for the 2020 Abu Dhabi International Petroleum Exhibition and Conference, Abu Dhabi, held virtually 9–12 November. The paper has not been peer reviewed. Hole cleaning in deviated wells is more challenging than in vertical wells because of the boycott effect or the eccentricity of the drillpipe. Poor hole cleaning can result in problems such as borehole packoff or excessive equivalent circulating density. The complete paper investigates a specialized fibrous material (Fiber 1) for hole-cleaning characteristics. The primary goal is to identify significant mechanisms of hole-cleaning fibers and their merits compared with polymeric high-viscosity pills. Hole-Cleaning Indices Based on a review of the literature, most effective parameters regarding hole cleaning in different well types were investigated. These parameters can be classified into the following five categories: - Well design (e.g., hole angle, drillpipe eccentricity, well trajectory) - Drilling-fluid properties (e.g., gel strength, mud weight) - Formation properties (e.g., lithology, cutting specific gravity, cuttings size and shape) - Hydraulic optimizations (e.g., flow regime, nozzle size, number of nozzles) - Drilling practices (e.g., drillpipe rotation speed, wellbore tortuosity, bit type, rate of penetration, pump rate) In this research, rheological parameters and parameters of the Herschel-Bulkley rheological model are considered to be optimization inputs to increase hole-cleaning efficiency of commonly used pills in drilling operations. The complete paper offers a detailed discussion of both the importance of flow regime and the role of the Herschel-Bulkley rheological model in reaching a better prognosis of drilling-fluid behavior at low shear rates. The properties of the fibrous hole-cleaning agent used in the complete paper are provided in Table 1. Test Method Two series of tests were performed. The medium of the first series is drilling water, with the goal of evaluating the efficiency of Fiber 1 in fresh pills. The second series of tests was per-formed with a simple polymeric mud as a medium common in drilling operations. Formulations and rheological properties of both test series are provided in Tables 4 and 5 of the complete paper, respectively.

Full Scale Flow Loop Experiments of Hole Cleaning Performances of Drilling Fluids

2015 ◽  
Author(s):  
Jan David Ytrehus ◽  
Ali Taghipour ◽  
Sneha Sayindla ◽  
Bjørnar Lund ◽  
Benjamin Werner ◽  
...  
Keyword(s):  
Test Section ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Flow Loop ◽  
Base Oil ◽  
Hole Cleaning ◽  
Cleaning Performance ◽  
Water Based ◽  
Fluid Properties ◽  
Drilling Cost

One important requirement for a drilling fluid is the ability to transport the cuttings out of the borehole. Improved hole cleaning is a key to solve several challenges in the drilling industry and will allow both longer wells and improved quality of well construction. It has been observed, however, that drilling fluids with similar properties according to the API standard can have significantly different behavior with respect to hole cleaning performance. The reasons for this are not fully understood. This paper presents results from flow loop laboratory tests without and with injected cuttings size particles using a base oil and a commercial oil based drilling fluid. The results demonstrate the importance of the rheological properties of the fluids for the hole cleaning performance. A thorough investigation of the viscoelastic properties of the fluids was performed with a Fann viscometer and a Paar-Physica rheometer, and was used to interpret the results from the flow loop experiments. Improved understanding of the fluid properties relevant to hole cleaning performance will help develop better models of wellbore hydraulics used in planning of well operations. Eventually this may lead to higher ROP with water based drilling fluids as obtained with oil based drilling fluids. This may ease cuttings handling in many operations and thereby significantly reduce the drilling cost using (normally) more environmentally friendly fluids. The experiments have been conducted as part of an industry-sponsored research project where understanding the hole cleaning performance of various oil and water based drilling fluids is the aim. The experiments have been performed under realistic conditions. The flow loop includes a 10 meter long test section with 2″ OD freely rotating drillstring inside a 4″ ID wellbore made of concrete. Sand particles were injected while circulating the drilling fluid through the test section in horizontal position.

Stabilization of Drilling Fluid Waste with Fly Ash

1986 ◽  
Vol 86 ◽  
Author(s):  
George M. Deeley ◽  
Larry W. Canter ◽  
Joakim G. Laguros
Keyword(s):  
Fly Ash ◽  
Caustic Soda ◽  
Drilling Fluid ◽  
Drilling Mud ◽  
Fly Ashes ◽  
High Calcium ◽  
High Calcium Fly Ash ◽  
Water Based ◽  
Land Disposal ◽  
Drilling Muds

Water based drilling muds typically contain clays, barite, lime, caustic soda and other chemicals, such as polymers. Land disposal of these wastes raises the possibility of groundwater pollution which can be abated if the waste is stabilized either by chemical reaction or by solidification through some form of cementation. Many ASTM high-calcium (Class C) fly ashes are cementitious and thus may be useful in stabilization of drilling mud. The basic idea is to stabilize the clay-containing muds using the model of soil and roadbed stabilization with high-calcium fly ash [1]. Fly ash that is not utilized is considered to be a solid waste, so this application would would actually constitute codisposal of two wastes.

New Drilling Muds for Drilling in Clay Rocks

2017 ◽  
Author(s):  
Sławomir Wysocki ◽  
Rafał Wiśniowski ◽  
Magdalena Gaczoł
Keyword(s):  
Side Chains ◽  
Atomic Mass Unit ◽  
Cationic Polymers ◽  
Technological Parameters ◽  
Mass Unit ◽  
Water Based ◽  
Amine Groups ◽  
Clay Rocks ◽  
Drilling Muds ◽  
Selection Of

The paper describes studies on the development of the new formulas of water-based drilling mud for drilling in clays and shales. The research were undertaken as a part of the OPTIDRILTEC project. First stage of the project included studies related to selection of ionic inhibitors of hydration. The tests of inorganic agents with various concentrations influence on technological parameters of the developed drilling muds was undertaken. The disintegration and linear swelling tests under influence of developed muds with different ionic inhibitors were conducted on the rock samples. Miocene shale was used as the model rocks. Within a framework of the project, it was conducted selection of the polymeric inhibitors of hydration. Subsequently, different polymers were tested for the influence on technological parameters of drilling muds as well as on disintegration and linear swelling of model rocks. Studies also consists of synthesis of short-chained cationic polymers (with primary amine groups in the side chains) and cationic-anionic polymers (with, apart amine groups, sulfonic amine groups). Synthesized polymers are characterized by low molecular masses (about 10.000 – 20.000 atomic mass unit) and small steric hindrance of side chains. The studies allowed development of new water-based mud formulas for drilling in clay rocks. Developed drilling muds are characterized by good technological parameters, resistance to temperature and to salts along with effective preservation against disintegration and swelling of clay rocks. Moreover, based on the research results it can be observed that synthesized cationic polymers are efficient inhibitors of clay rocks hydration. Newly developed drilling muds could be successfully applied in the oil and gas industry causing improved drilling conditions and decreased drilling costs.

Sign in / Sign up

Export Citation Format

Share Document